Ozito PXBPRS-018 Handleiding

Ozito Niet gecategoriseerd PXBPRS-018

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXBPRS-018 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
STANDARD EQUIPMENT
5 6
0
½”
1”
1½”
5m m
10mm
15mm
20m m
25m m
m
5 6
0
½”
1”
1½”
5mm
10mm
15mm
20mm
25mm
m
PXBPRS-018
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 10,000 - 30,000/min
Collet Size: 6.35mm & 8mm
Max. Cutter Size: 28mm
Dust Port Size: Ø35mm
Weight: 2.8kg
ozito.com.au
1022
Brushless Plunge Router
Dust Extraction Port & Parallel
Guide
8mm Collet, Compass Point &
2 x Spanners (22 & 13mm)
PLUNGE
ROUTER
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, VIC 3175, Australia.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
5
0
1”
1½”
5mm
10mm
15mm
20mm
25mm
m
1. Depth Adjustor
2. Depth Scale
3. Battery Seating
4. Speed Control Dial
5. Lock Off Switch
6. On/Off Switch
7. Plunge Handles
8. Plunge Router Base
9. Collet Nut
10. Guide Mount Screw
11. Accessory Mounting Arm
12. Mounting Arm Screw
13. Plunge Lock
14. Dust Extraction port
15. Dust Extractor Screw
16. Plunge Base Lock
17. Baseplate
18. Clear View Window
19. Turrent
20. Spindle Lock
21. Depth Adjustor Lock Button
22. Height Marker
This tool is compatible with all batteries & chargers from the Ozito PXC range.
For optimal performance, we recommend the use of a 3.0Ah battery or
higher to operate this PXC Trim Router.
BRUSHLESS PLUNGE ROUTER
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
Installing A Router Bit
When using the plunge router, only use router bits that:
• are suitable for cutting wood or plastic,
• has a suitable shank diameter for the collet mounted (collet size:
6.35mm & 8mm),
• has a maximum diameter of 28mm,
• are suitable for the router’s speed (n0 = 10,000-30,000/min).
1. Remove the plunge router base from the
router unit.
2. Place the smaller supplied spanner on
the spindle and use the large spanner to
loosen the collet nut.
Note: If a different collet size is required,
remove the collet nut entirely and replace
the collet. Re-attach the collet nut but don’t
tighten it all the way.
3. Fully insert the shaft of the router bit (not
supplied) into the collet.
4. Press and hold down the spindle lock
while tightening the collet nut with your
ngers.
5. Release the spindle lock and then use the
2 spanners to fully tighten the collet nut.
WARNING! THE SPINDLE LOCK IS NOT ALLOWED
TO BE USED FOR TIGHTENING WITH THE SPANNER.
TIGHTEN THE CLAMP NUT USING THE TWO
SPANNERS.
mm 00 in.
10
1/2
20
mm 00 in.
10
1/2
20
mm 00 in.
10
1/2
20
mm 00 in.
a.
b.
3 41
7
2
5
15
16
19
18
20
17
21
22
8
9
13
14
6
1112 10
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING! WEAR GLOVES WHEN HANDLING
ROUTER BITS AS THEY CAN BE SHARP AND/OR
HOT TO THE TOUCH AFTER USE.
WARNING! ONLY USE THE ROUTER UNIT WITH A
COMPATIBLE BASE. USING IT WITHOUT A BASE
OR WITH AN INCOMPATIBLE BASE MAY RESULT IN
SERIOUS INJURY.
2. STRAIGHT CUTS
Attaching The Parallel Guide
The parallel guide helps to maintain
a straight path when chamfering or
lleting edges and cutting slots or
grooves.
1. Loosen the guide mount screw.
2. Slide the parallel guide arm
between the washer and router
base. Push it all the way up until
the straight edge is ush with the
router base.
3. Tighten the guide mount screw to lock the
guide in place.
Adjusting The Parallel Guide
1. Loosen the fence locking wingnut.
2. Place the fence along the side of
the workpiece.
3. Set the cutting distance by
sliding the plunge router to the
desired cutting position.
4. Tighten the fence locking wingnut to set
the distance in place.
0
5 6
0
½”
1”
1½”
5mm
10mm
15mm
20mm
25mm
m
0
½”
1”
5mm
10mm
15mm
20mm
25mm
Attaching The Dust Extraction Adaptor
1. Slide the tabs on the extraction adaptor
ring into the slot on the baseplate.
2. Tighten the dust extractor screw to lock
the adaptor in place.
3. Connect a suitable vacuum or dust
extraction system to the dust extraction
adaptor for use with the router.
Attaching & Removing The Plunge Router Base
1. Loosen the plunge base lock.
2. Slide the router into the
router base.
3. Tighten the plunge base lock.
4. To remove the base, loosen the plunge base lock and pull the base off the
router.
Fitting A Battery
1. Slide the battery into the tool base until it
clicks into place.
2. Hold down the battery release
button and then slide the battery
out.
b.
a.
a.
b.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: PXBPRS-018

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXBPRS-018 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024
Ozito

Ozito PXDDGK-600U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024