Ozito ACO-PRO Handleiding

Ozito Niet gecategoriseerd ACO-PRO

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito ACO-PRO (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 124 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

WARNING! Do not use accessories which are not specifically designed and

recommended by the tool manufacturer. Just because the accessory can be attached

to your power tool, it does not assure safe operation.

• The rated speed of the accessory must be at least equal to the maximum speed marked

on the power tool. Accessories running faster than their rated speed can break and fly apart.

• Wear personal protective equipment. Depending on application, use face shield, safety

goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and

workshop apron capable of stopping small abrasive or workpiece fragments. The eye

protection must be capable of stopping flying debris generated by various operations . The dust

mask or respirator must be capable of filtrating particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing loss.

• Never place your hand near the rotating accessory. Accessory may kickback over your

hand.

• Do not position your body in the area where power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the wheel’s movement at the point of

snagging.

DESCRIPTION OF SYMBOLS SPARE PARTS

AIR CUT-OFF

TOOL

76.2mm (3”)

INSTRUCTION MANUAL

SPECIFICATIONS

ACO-PRO

Max Air Pressure: 90psi (6Bar)

Av. Air Consumption: 170l/min (6cfm)

No Load Speed: 20,000/min

Wheel Diameter: 76.2mm (3”)

Air Inlet: 1/4“ BSP

Weight: 0.76kg

Guard Lock Nut SPACOPRO-28

3” Cutting Blade SPACOPRO-29

Blade Bolt & Washer SPACOPRO-30A

Spanner SPACOPRO-33

Spare parts can be ordered from the Special Orders Desk at

your local Bunnings Warehouse.

For further information, or any parts not listed here, visit

www.ozito.com.au or contact Ozito Customer Service:

Australia 1800 069 486

New Zealand 0508 069 486

Email: enquiries@ozito.com.au

Warning Read instruction

manual

Wear eye protection

No load speed

Wear ear protection

Revolutions or

reciprocation per minute

/min no

GENERAL AIR TOOL SAFETY WARNINGS

AIR CUT-OFF TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings

refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Cluttered or dark areas invite accidents. Keep work area clean and well lit.

b. Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

or fumes.

c. Distractions can Keep children and bystanders away while operating a power tool.

cause you to lose control.

d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

e. Check the maximum pressure rating of any tools or accessories that you intend using with

the compressor. The output pressure of the air from the compressor must be regulated so

that it never exceeds the rated pressure of the tool or accessory.

f. Always wear safety goggles or glasses when using the air compressor. Never point the

nozzle of an accessory towards any part of your body or towards another person.

g. Drain the moisture from the tank daily. It will help prevent corrosion.

h. Use safety equipment including safety goggles or shield, ear protection, breathing respirator

mask and protective clothing.

i. Air tools should not be used in a potentialy explosive environment.

j. Use safety equipment including safety goggles or shield, ear protection, breathing or

respirator mask and protective clothing.

k. Any use other than those mentioned The tool must be used only for its prescribed purpose.

in this Manual will be considered a case of misuse. The user and not the manufacturer

shall be liable for any damage or injury resulting from such cases of misuse.

WARNING! In the event that an air line is cut or broken, the air supply must be turned off

at the compressor. A broken air line which is not supported is extremely dangerous and

can whip around very quickly, both with the capability of striking people, and blowing foreign

particles into the air.

Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air

supply to the hose, turn off the compressor at the On / Off button, and then remove the hose from

the compressor.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given the supervision or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

• Such blades create Do not attach a saw chain woodcarving blade or toothed saw blade.

frequent kickback and loss of control.

• Use special care when working corners, sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or kickback.

• Wheels must be used only for recommended applications. For example: do not grind

with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them to shatter.

• Always use undamaged wheel flanges that are of correct size and shape for your

selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

• Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to

twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

• Do not restart the cutting operation in the workpiece. Let the wheel reach full speed

and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is

restarted in the workpiece.

KNOW YOUR PRODUCT

1 Cutting Disc

2 Guard

3 Spindle

4 Lock-off Lever

5 On/Off Trigger

6 Air Inlet

TROUBLESHOOTING

MAINTENANCE

If the air cut-oﬀ tool fails to work eﬀecvely, perform the

following checks:

• Check the air inlet is free of any dirt or blockages.

• Ensure the tool is lubricated properly.

• Check that the pressure on the air compressor is within its

||working range. If not, let the compressor rest to

||re-pressurise / refer to the compressor instruction manual.

• Keep the ventilation vents of the cut-off tool clean at all times,

if possible, prevent foreign matter from entering the vents.

• If the enclosure of the tool requires cleaning, do not use

solvents but a moist soft cloth only. Never let any liquid get inside

the tool; never immerse any part of the cut-off tool into a liquid.

• Oil the cut-off tool after each use.

CONNECTING TO COMPRESSOR

OPERATION

ATTACHING TOOLS

3. Screw the male nio ﬁng

clockwise into the air inlet.

4. Pull back the sleeve on hose

ﬁng, insert male end & release

sleeve on hose ﬁng.

1. Remove black plasc cap

from the air inlet.

2. Wrap the threaded male

end with teﬂon tape in a

clockwise direcon.

3. Place washer and blade bolt

onto the spindle.

4. Tighten the blade bolt using the

provided hex key and spanner in

opposite direcons.

1. Undo the spindle using

the provided hex key and

spanner turning in

opposite direcons.

2. Place the cung disc onto

the spindle with the metal

ring facing down.

2. To turn the tool on squeeze the

on/oﬀ trigger.

1. Push and hold the lock-oﬀ lever

forward.

3. To turn oﬀ, release the on/oﬀ

trigger.

Note: Disconnect the tool from the air supply before performing the below operaons.

Note: This tool is rated at 90psi. Ensure your compressor is set no higher than 90psi.

Product specificaties

Merk:	Ozito
Categorie:	Niet gecategoriseerd
Model:	ACO-PRO

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito ACO-PRO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024

Ozito PXNGS-218 Handleiding

8 April 2024

Ozito PXHTBK-2518 Handleiding

8 April 2024

Ozito PSR-5732U Handleiding

16 Maart 2024

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024

Ozito PXWBS-200U Handleiding

16 Maart 2024

Ozito PXDDK-301U Handleiding

16 Maart 2024

Ozito PXCPPS-018U Handleiding

16 Maart 2024

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Ozito PXDDGK-600U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024