Ozito OZCCS85WA Handleiding
Ozito
Zaagmachine
OZCCS85WA
Lees hieronder de đ handleiding in het Nederlandse voor Ozito OZCCS85WA (8 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
CHAINSAW
CHAIN
SHARPENER
85W
INSTRUCTION MANUAL
OZCCS85WA
WHATâS IN THE BOX
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: wheel.
WARNING
The following actions will result in the warranty being void.
â˘î If the tool has been operated on a supply voltage other
thanîthatîspeciîˇedîonîtheîtool.
â˘î If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
â˘î Failure to perform maintenance as set out within the
instruction manual.
â˘î If the tool is disassembled or tampered with in any way.
â˘î Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/NewîZealandî(HeadîOfîˇce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
Theîbeneîˇtsîprovidedîunderîthisîwarrantyîareîinîadditionî
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1014
SPECIFICATIONS
Motor: 85W
Input: 230V-240V ~ 50Hz
No load speed: 4,800/min
Table/vice angles: 0 â 35° left & right
Sharpening Wheel: Ă108 x 3.2mm
Bore: Ă23mm
Suits chain pitch: 0.325â and 3/8â
Weight: 2.4kg
Chainsaw Chain Sharpener
Sharpening Wheel
(assembled)
Table & Lock Knob
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Assembling the table
1. Insert the bolt of the table through
the hole in the base.
2. Secure the table in place by îżxing
the locking knob to the bolt (by
screwing the knob clockwise).
Mounting the sharpener
For safe operation of the sharpener, the base of the tool must be îżtted to
a îat, solid, secure surface such as a work bench.
The sharpener base is designed in two halves. The rear half is for îżtting
îat to a stable surface and the front is designed to protrude over the edge
of the mounting surface.
The sharpener base should
be îżtted to the mounting
surface by sliding the
rear half back until the
two âstepsâ on the base
align with the edge of the
mounting surface. Ensure
when mounting, that the
table locking knob is still
easily accessible for when
adjusting the table angles.
Two 6mm mounting holes allow for îżxing
the base to the mounting surface (bolts
not supplied). Ensure the mounting
surface is capable of supporting the
weight of the sharpener and chain to
be sharpened.
1. Lowering hand piece
2. Sharpening wheel cover
3. Direction of rotation indicator
4. Safety guard
5. Sharpening wheel
6. Depth of grind knob
7. Depth of grind locking knob
8. Depth of grind pin
9. Guide clamp lever
10. Chain (tooth) stop
11. Guide
12 Depth stop platform
13. Table locking knob
14 Bench mounting holes
15. Sharpener base
16. Chain stop adjusting
knob lock nut
17. Adjustable table
18. Chain stop adjusting knob
19. Table scale
CHAINSAW CHAIN SHARPENER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
6
2
16
7
4
17
3
18
8
9 10 11
13
12
14 15
19
WARNING!: BEFORE ASSEMBLING, MOUNTING,
SETTING OR MAINTAINING YOUR SHARPENER,
MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL
DISCONNECTED FROM THE POWER SUPPLY TO PREVENT
ACCIDENTAL STARTING.
1
5
4. If you do not know the angle of the chain
set, the table angle to 35°.
Take hold of the hand piece and bring it
down so that the wheel is slowly lowered
into the chain, along the cutting tooth.
Slowly move the table so the cutting face
of the tooth is parallel with the edge of the
wheel. The most common chain angles
are 30 35°. It may be necessary to slide â
the chain slightly to allow the wheel to
enter down the face of the tooth.
5. Once the correct angle as been achieved
tighten the table locking knob to lock the
table in the current position.
After the table is locked in the required
position, take hold of the hand piece and
lower the head assembly until the wheel
is aligned along the tooth of the chain.
Conîżrm the angle then slide the chain so
the face of the tooth is just touching the
face of the wheel.
6. Lock the guide by rotating
the clamping lever as far
as it will go in a clockwise
direction. Ensure the chain
is clamped îżrmly into the
sliding guide. Should the
chain still not be clamped,
pull the clamping lever
outwards (away from the
guide), turn the lever anti-
clockwise 1/4 of a turn.
Push the lever back in towards the guide.
Proceed to rotate the lever fully clockwise.
Check the chain is clamped. Should it
still not be clamped, repeat the process
above.
2. SETTING OF THE SHARPENER
Note. Prior to using the sharpener, several adjustments must be made in
order to sharpen the teeth of the chain effectively.
1. Adjusting the angle of cut.
2. Adjusting the chain (tooth) stop.
3. Adjusting the depth of cut.
Failure to perform these adjustments will result in poor sharpening and
possible damage to the chain being sharpened.
Before making adjustments, always ensure the sharpener has been
disconnected from the power supply.
Adjusting the angle of cut
1. Open the slide guide groove
by rotating the guide clamp
lever anti-clockwise.
2. Fit a chain over the guide groove
ensuring the inner side of the chain
sits inside the guide groove. Ensure
the chain hangs freely over the side
of the mounting surface. The chain
should be îżtted so the teeth face the
right hand side of the sharpener and
the chain can move freely in both
directions.
3. If you know the angle of the chain,
rotate the table to the same angle as
the chain. To rotate the table loosen
the table lock knob and rotate the
table until the scale indicator lines
up with the scale on the base of the
sharpener.
Product specificaties
| Merk: | Ozito |
| Categorie: | Zaagmachine |
| Model: | OZCCS85WA |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito OZCCS85WA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaagmachine Ozito
9 Juli 2023
26 Juni 2023
24 Juni 2023
20 Juni 2023
18 Juni 2023
16 Juni 2023
13 Juni 2023
13 Juni 2023
11 Juni 2023
9 Juni 2023
Handleiding Zaagmachine
- Zaagmachine Bosch
- Zaagmachine AEG
- Zaagmachine DeWalt
- Zaagmachine Ford
- Zaagmachine Al-ko
- Zaagmachine Atika
- Zaagmachine BabyGO
- Zaagmachine Batavia
- Zaagmachine Bavaria
- Zaagmachine Bebe Confort
- Zaagmachine BGU
- Zaagmachine Blucave
- Zaagmachine Bort
- Zaagmachine Brennenstuhl
- Zaagmachine Bruder Mannesmann
- Zaagmachine Budget
- Zaagmachine Defort
- Zaagmachine Dolmar
- Zaagmachine Dremel
- Zaagmachine Duro
- Zaagmachine Echo
- Zaagmachine Einhell
- Zaagmachine Elektra Beckum
- Zaagmachine Elu
- Zaagmachine Ergofix
- Zaagmachine Exakt
- Zaagmachine Fein
- Zaagmachine Felisatti
- Zaagmachine Ferm
- Zaagmachine Ferrex
- Zaagmachine Festool
- Zaagmachine Flex
- Zaagmachine Florabest
- Zaagmachine FOM
- Zaagmachine Fuxtec
- Zaagmachine Gamma
- Zaagmachine Gardena
- Zaagmachine Gardenline
- Zaagmachine Germania
- Zaagmachine Global
- Zaagmachine Greenworks
- Zaagmachine Grizzly
- Zaagmachine Gude
- Zaagmachine Gude Pro
- Zaagmachine Hammer
- Zaagmachine Hikoki
- Zaagmachine Hitachi
- Zaagmachine Holzmann
- Zaagmachine Homelite
- Zaagmachine Husqvarna
- Zaagmachine Huvema
- Zaagmachine Hyundai
- Zaagmachine Ideal
- Zaagmachine Kompernass
- Zaagmachine Kress
- Zaagmachine Lux Tools
- Zaagmachine Luxor
- Zaagmachine Maestro
- Zaagmachine Makita
- Zaagmachine Maktec
- Zaagmachine Matrix
- Zaagmachine Max
- Zaagmachine Maxx
- Zaagmachine McCulloch
- Zaagmachine Metabo
- Zaagmachine Milwaukee
- Zaagmachine Parkside
- Zaagmachine Pattfield
- Zaagmachine Plantiflor
- Zaagmachine Powerfix
- Zaagmachine Powerplus
- Zaagmachine Remington
- Zaagmachine Robust
- Zaagmachine Ryobi
- Zaagmachine Scheppach
- Zaagmachine Shindaiwa
- Zaagmachine Silverline
- Zaagmachine Skil
- Zaagmachine Stanley
- Zaagmachine Sterwins
- Zaagmachine Stiga
- Zaagmachine Stihl
- Zaagmachine Tanaka
- Zaagmachine Texas
- Zaagmachine Toledo
- Zaagmachine Toolcraft
- Zaagmachine Topcraft
- Zaagmachine Trotec
- Zaagmachine Troy-Bilt
- Zaagmachine Varo
- Zaagmachine Vonroc
- Zaagmachine Westfalia
- Zaagmachine Workzone
- Zaagmachine Worx
- Zaagmachine Zipper
- Zaagmachine Black And Decker
- Zaagmachine Cocraft
- Zaagmachine Draper
- Zaagmachine Meec Tools
- Zaagmachine Lionelo
- Zaagmachine Clarke
- Zaagmachine Genesis
- Zaagmachine Hilti
- Zaagmachine Cobra
- Zaagmachine Hobart
- Zaagmachine ACG
- Zaagmachine Cotech
- Zaagmachine Power Craft
- Zaagmachine Tacklife
- Zaagmachine Truper
- Zaagmachine Fieldmann
- Zaagmachine Mafell
- Zaagmachine Proxxon
- Zaagmachine Biltema
- Zaagmachine Porter-Cable
- Zaagmachine Sun Joe
- Zaagmachine Yard Force
- Zaagmachine Challenge
- Zaagmachine EGO
- Zaagmachine Hurricane
- Zaagmachine Sovereign
- Zaagmachine Spear & Jackson
- Zaagmachine Dedra
- Zaagmachine Graphite
- Zaagmachine Narex
- Zaagmachine RIDGID
- Zaagmachine Tryton
- Zaagmachine Herkules
- Zaagmachine Powerworks
- Zaagmachine Sthor
- Zaagmachine Craftsman
- Zaagmachine Rikon
- Zaagmachine Verto
- Zaagmachine Erbauer
- Zaagmachine Snow Joe
- Zaagmachine Chicago Pneumatic
- Zaagmachine Alpha Tools
- Zaagmachine Hazet
- Zaagmachine Yato
- Zaagmachine Jonsered
- Zaagmachine Qualcast
- Zaagmachine Avantco
- Zaagmachine Masport
- Zaagmachine Morrison
- Zaagmachine Baumr-AG
- Zaagmachine Martha Stewart
- Zaagmachine IKRA
- Zaagmachine MTM
- Zaagmachine Meister Craft
- Zaagmachine Ĺucznik
- Zaagmachine King Craft
- Zaagmachine Toolson
- Zaagmachine Wolfcraft
- Zaagmachine Kreg
- Zaagmachine Vulcan
- Zaagmachine Challenge Xtreme
- Zaagmachine Pro-Cut
- Zaagmachine Power Smart
- Zaagmachine Backyard Pro Butcher Series
- Zaagmachine EFA
- Zaagmachine Einhell Bavaria
- Zaagmachine McKenzie
- Zaagmachine Proviel
- Zaagmachine Ultranatura
- Zaagmachine FIXIT
- Zaagmachine Ergotools Pattfield
- Zaagmachine MyTool
- Zaagmachine Bavaria By Einhell
- Zaagmachine Donau Elektronik
- Zaagmachine Rona
Nieuwste handleidingen voor Zaagmachine
26 April 2024
15 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
9 April 2024