Olight S80 Baton Handleiding

Bekijk gratis de handleiding van Olight S80 Baton (1 pagina’s), behorend tot de categorie Zaklamp. Deze gids werd als nuttig beoordeeld door 38 mensen en kreeg gemiddeld 4.9 sterren uit 6 reviews. Heb je een vraag over Olight S80 Baton of wil je andere gebruikers van dit product iets vragen? Stel een vraag

S80 Baton maintains Olight S series’s simple, reliable and easy of use advantages. A customized 4000mAh

26650 lithium rechargeable battery inside, integrated charge port, output up to 750lumens. It is a preferred

flashlight for household illumination, outdoor and industry field application.

Olight Technology Co., Limited

www.olightworld.com

Tel: +86-755-3351 8606

Fax: +86-755-3380 0207

Email:service@olightworld.com

TM

Operator's Manual

LED Flashlight

S80 BATON

Diffuser

Holster

Customized 26650 Lithium

Rechargeable Battery

Supplied Accessories

Specification

2

4

5

6

3

Key-ring

Operation Instrution

Operator’s Manual ( this manual)

Charger

Warranty

1

9

7

size:147*105

TM

WE MAKE A DIFFERENCE

S80 Baton手电筒保持Olight S 系列简洁，坚固，易用等内置定制4000毫安时 26650可充锂电，并具

有充电接口，手电输出达到750流明。 S80是家用照明，户外及工业领域应用的首选产品。

优异特征, 它

定制 26650 可充锂电池

即时点亮：关机状态下， 按下开关按键并保持1秒或以上， 按下时开，释放时关 。

开、关机： 按下开关按键并在1秒内释放。每次开机，手电输出在前次关机时记忆的亮度级。

改变模式： 开机状态下，按住开关按键并保持，手电输出亮度在"低-中-高"之间循环，释放按键

将选定当前的亮度。

暴闪模式： 快速连按开关按键二次(初始状态为关需按三次)。在暴闪状态下，按下开关，1秒内

释放，输出关闭；如超出1秒，输出记忆的亮度。

锁按键： 开机状态下，按下开关按键并保持，输出经历 “低-中-高”循环三次后自动关闭，

手电进入锁定状态；在锁定状态, 如开关按键被意外按下, 手电不会开机，开关按键

处的灯将点亮1秒。

解 锁： 在锁定状态，需快速连击按键三次解锁并开机。重新装入电池也会自动解锁。

充 电： 连接充电器到电源插板或墙壁插孔, 揭开手电尾端充电接口软塞，将充电器DC插头插

入。充电状态指示灯位于充电器。 指示灯显示状态：

红色 -- 充电进行中； 绿色 -- 充电完成或未连接手电。

充电完成后，将充电器从电源插板或墙壁插孔取下, 请拔出DC插头，并塞紧充电接

口软塞。

警告 充电完成后，请及时断开电源，勿将充电器长时间连接到市电；不充电

时，请勿将手电连接到充电器 。

更换电池： 请使用厂家提供的电池。 先逆时针方向旋开手电尾盖，将电池取出后，将入新电

池；电池正极朝向手电前端装入，然后旋紧尾盖。见以下电池极性标识图：

1 发光二极管

2 透镜

3 不锈钢攻击头

4 开关按键

5 筒身

6 尾盖

7 软塞固定螺钉

/ 钥匙环固定孔

8 充电接口

9 充电接口软塞

特 征

主体材料

攻击头材料

体 积

重 量

颜 色

反光杯

开 关

透 镜

发光二极管

电 池

输出亮度级 / 运行时间

特殊模式

峰值光强

最大射程

抗冲击

防 水

低电压提示 / 低压关机

充电器

充电时间

主动热管理

钥匙环孔

size:147*105

产品部件

随机配件

手电包

滤镜

钥匙圈

用户手册 (本手册)

充电器

保修卡

操作说明

规 格

规 格

6N01-T6 铝材，表面三级硬质阳极氧化

不锈钢

头部直径 39.6毫米 / 筒身直径 32.5毫米 / 总长度 154毫米

277克 （包含电池）

黑色

铝构造，橘皮反射面

侧按键，轻触开关 + 硅胶帽

钢化加硬玻璃，双面镀增透膜，单面防水膜

Cree XM-L

定制4000毫安时 26650可充锂电池

10流明 / 80小时 ; 180流明 / 8小时; 750流明 / 2小时

暴闪，10赫兹

16650 坎德拉

260 米

2米跌落， 6个方向，每个方向2次

IPX8

电压低于3.15±0.05伏时, 开关键键底部指示灯以间隔3秒闪两次的速度闪动,

同时亮度自动至低一级的档, 最低亮度档低于3.15伏 时关断电源供应±0.05

输入电压：交流 100～240伏 50/60赫兹; 输出: 恒流恒压 1安掊 4.2伏

约5小时

采用热敏电阻测试内部温度，当内部温度达到约85度时，在10分钟内，

输出平滑下降到最大亮度的60% 然后稳定在这个亮度

位于尾盖底部软塞固定螺钉

Characteristics

Material

Bezel

Size

Weight

Color

Reflector

Switch

Lens

LED

Battery

Flux / Runtime

Special Mode

Peak beam intensity

Max Beam Distance

Impact Strength

Waterproof

Low Battery Prompt / LVSD

Charger

Charging time

Active thermal management(ATM)

Key-ringHole

6N01-T6 AL, Class-III harden anodization treating

Stainless Steel

Head D39.6mm / Body D32.5mm / TotalLength154mm

277g ( with battery)

Black

Orange peel, aluminum machining

Side button switch

Hardened glass, double sides AR coating, single side anti-water coating

Cree XM-L LED

Customized 4000mAh 26650 lithium rechargeable battery

10 lm / 80h; 180 lm / 8h; 750 lm / 2h

Strobe 10hz, 750lm

16650cd

260meters

2 meters dropping, 6 directions, twice each.

IPX8

Input: 100 to 240 VAC, Output: CC/CV1A， 4.2V

About 5 hours

Locating at fixingscrew of soft-cover in the tail cap

Underoffstatus,pressthebuttonswitch and hold 1 second or above, the light turns on

at moment that the button switch is pressed and turns off when the button switch is

released.

Press then release the button switch within 1 second. Everyrestart, output brightness

keeps same as previous memorized brightness.

While on, pressandholdthebuttonswitch, outputwill change by the order “Low-

Medium-High", releasing the button switch will froze the output at presented

brightness.

Quickly press the button switch twice (ifinitialstatusisoff, triply press)。Understrobe

status, pressingthen releasing the button switch whin 1 second will turn off the output, if

the hold time over 1 second, thelightrestores to memorized brightness

Whileon, hold the button switch until the light becomes off. Usually the output will

experience three loops of“Low-Medium-High”before entering into off; Under lock

status, the hidden lamp under the button switch will turn on 1 second while the button

switch is unexpectedly pressed, but the light will not turn on.

Triply click the button switch within 1 second or reinstall after taking out the battery.

ConnectthechargertoAC power source or wall socket, then discover the soft-cover

and insert DC plug of charger into the charge port. The indication ofthecharger displays

the charge status. See below:

Red -- charging in progress； Green -- completed or not connected 。

When charge completed, please take off the charger from AC power source or wall

socket, and pull out the DC plug , insert the soft-cover into his seat.

Don’t always connect the charge with AC power source after charge

completed, it may cause to fire.Don’t longtimeconnectDCplugtogether

withtheflashlightwhileno charge.

2

4

5

6

3

1

8

9

7

8

Specification

1 LED

2 Lens

3 Stainless Steel Bezel

4 Button Switch

5 Body

6 Tail Cap

7 Fixing Screw of Soft-cover

/ Key-ring Hole

8 Charge Port

9 Soft-cover

Parts of the Flashlight

Momentary On:

Turn ON/OFF:

ChangeMode:

Strobe:

Lock Button Switch:

Unlock:

Charge:

Warning

ReplacingBattery:

Pleaseusingthefactory supplied battery. Firstly, counterclockwise unscrew and take

out the tail cap, then take out the battery and insert the fresh battery, the positive of

battery should towards the head of the flashlight. Refer to below figure

正极

充电输入正

负极( 充电输入负)

Wheninternal MCU detects the inner temperature over 85℃，within next

10 minutes, it will make regular and controls the output smoothly drop

to 60% of maximum brightness, then staying at this brightness level

When battery voltage drops to , the lampunder the button

switch will flash twice per 3 seconds interval, and theoutputwill

automaticallyjump to lower brightness level. If the flashlight is running at

low brightness level, MCU will shut off the power supply.

3.15±0.05V

Positive

Negative( Charge Input-)

ChargeInput+

Product specificaties