Nemco 57500-6 Handleiding
Nemco
Snijmachine
57500-6
Lees hieronder de 📖 handleiding in het Nederlandse voor Nemco 57500-6 (2 pagina's) in de categorie Snijmachine. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.4 sterren beoordeeld
Pagina 1/2
Easy Chopper 3
Model: 57500-( )
OPERATING AND MAINTENANCE INSTRUCTIONS
Important
1. To get the best operation and life from your Easy Chopper 3, please read and comply with these instructions.
2. Clean machine thoroughly before first use and after each use using cleaning instructions below.
3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.
Safety Instructions
Remember that the blades are VERY SHARP; be careful when handling and operating the equipment to keep hands
away from the cutting edges.
Operation of Easy Chopper 3
1. Always check the equipment before each use to ensure that it is clean & free of debris. Also inspect the blades to ensure
there are no broken, nicked, or dulled blades and if found, replace the blade assembly before using the equipment again.
2. Place the chopper on a firm, clean, and flat work surface.
3. Be sure that the cleaning gasket is in place before using. Also, ensure that the color of the push block matches the colored
indicator on the blade assembly to confirm they are a matching set.
4. Prepare the produce to be cut (Chopped, Sliced, or Wedged).
5. Lift HANDLE and place the produce on the blades with the flat side down.
6. Remove hand/fingers from the cutting area, use free hand to grasp the leg of the frame, and with a strong, quick thrust,
bring the PUSH BLOCK down to force the produce through the BLADES. Lift and repeat.
7. Clean the machine after prep work is completed using cleaning instructions below.
Caution: Do not attempt to chop produce larger than the opening in the BLADE HOLDER (4- -1/4” x 4 1/4”).
Note: Additional blade and PUSH BLOCK sets can be purchased separately. Be sure to always use a PUSH BLOCK and blade set
that are compatible or damage to the equipment will result. To check for compatibility, compare the color of the push block to the
colored indicator on the blade assembly. The color of the cleaning gasket should match the push block and blade assembly as
well.
To Clean
1. Remove the PUSHER assembly off the GUIDE RODS. Using the tabs on the cleaning gasket, pull the cleaning gasket from
the push block to remove debris from the slots.
2. Remove the blade assembly from the locating pins.
3. Thoroughly wash the PUSHER & BLADE assemblies, and cleaning gasket using warm water and a mild detergent.
CAUTION: Do not wipe across the sharp side of the blades, or use abrasive pads on the blades. Wiping across the sharp
side of the blades in any form may cause injury and will dull the blades.
4. To aid cleaning, spray pressurized water across the blade assembly from the dull side to force out debris. Pressurized water
can also be sprayed on the push block to force out remaining debris.
5. Allow all pieces to air dry.
6. Once all pieces are dry, reassemble the components to the Chopper. It is suggested that mineral oil is applied to the guide
rods every time the equipment is cleaned.
Chopping Tips
Cut produce before chopping and place a cut surface against the BLADES. Onions and tomatoes dice best if cut from top to
bottom. They may be cut in half, or if smaller dices are desired, they can be cut several times in this direction.
To Lubricate
When needed, lubricate the GUIDE RODS with Mineral Oil, Food Grade Lubricant, or rub them with Paraffin.
DO NOT LUBRICATE WITH COOKING OIL IT GETS STICKY! –
NEMCO FOOD EQUIPMENT - 301 Meuse Argonne, Hicksville, Oh 43526
Phone: (419) 542- Fax: (419) 542-6690 Toll Free: 800- -6761 7751 – – 782
www.NemcoFoodEquip.com
6- 2015
57500-1
57500-2
57500-3
57500-4
57500-5
57500-6
57500-7
Description
1
55446
55446
55446
55446
55446
55446
55446
HANDLE
2
45652
45652
45652
45652
45652
45652
45652
SCREW, #10-24
3
57403
57403
57403
57403
57403
57403
57403
PUSH BLOCK GUIDE
4
57431
57431
57431
57431
57431
57431
57431
GUIDE ROD
5
56383
56383
56383
56383
56383
56383
56383
LOCATING PIN
6
57432
57432
57432
57432
57432
57432
57432
BUMPER
7
57429
57429
57429
57429
57429
57429
57429
FRAME
8
45457
45457
45457
45457
45457
45457
45457
RUBBER FOOT
9
46091
46091
46091
46091
46091
46091
46091
NYLOCK NUT, 5/16- 18
10
45154
45154
45154
45154
45154
45154
45154
WASHER, 5/16”
11
57424-1
(Red)
57424-2
(Blue)
57424-3
(Green)
57424-4
(Black)
57424-5
(Red)
57424-6
(Blue)
57424-7
(Green)
BLADE ASSEMBLY
12
56381-1
(Red)
56382-2
(Blue)
56381-3
(Green)
56382-4
(Black)
56381-1
(Red)
56382-2
(Blue)
56381-3
(Green)
CLEANING GASKET
13
57417-1
(Red)
57418-2
(Blue)
57417-3
(Green)
57418-4
(Black)
57417-1
(Red)
57418-2
(Blue)
57417-3
(Green)
PUSH BLOCK
14
55435
55435
55435
55435
55435
55435
55435
BUSHING
15
45362-2
45362-2
45362-2
45362-2
45362-2
45362-2
45362-2
THUMB SCREW, ¼- 20
Product specificaties
| Merk: | Nemco |
| Categorie: | Snijmachine |
| Model: | 57500-6 |
Heb je hulp nodig?
Als je hulp nodig hebt met Nemco 57500-6 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Snijmachine Nemco
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
Handleiding Snijmachine
- Snijmachine Saturn
- Snijmachine ECG
- Snijmachine Backyard Pro Butcher Series
- Snijmachine Prince Castle
- Snijmachine Ovela
- Snijmachine Genius
- Snijmachine Graef
- Snijmachine Arendo
- Snijmachine Prowork
- Snijmachine Ices
- Snijmachine Toolland
- Snijmachine Kleva
- Snijmachine Royal Catering
- Snijmachine GARDE
- Snijmachine Tristar
Nieuwste handleidingen voor Snijmachine
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025