Mikrotik wAP LR9 kit Handleiding

Mikrotik Niet gecategoriseerd wAP LR9 kit

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik wAP LR9 kit (11 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 91 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/11

wAP LR9 kit

wAP LR9 kitwAP LR9 kit

wAP LR9 kit

The wAP is a small weatherproof device with an integrated LR9 card for UDP packet forwarding to the chosen server.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole but can also be installed indoors. Please read the mounting instructions carefully before

beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to

people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the European Union radiation exposure limits set forth for an uncontrolled

environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the general public.

Quickstart

Make sure your ISP is allowing hardware change and will issue an automatic IP address.

Open the bottom lid.

Connect an external antenna to the SMA connector.

Connect the device to the power source.

Connect with your device to the MikroTik wireless network

The configuration has to be done through the wireless network using a web browser or mobile app. Alternatively, you can use the WinBox

configuration tool . By default, Ethernet port access is blocked by a firewall.https://mt.lv/winbox

Once connected to the wireless network, open in your web browser to start the configuration. https://192.168.88.1

user name: a and there is no password by default .

dmin

 (or, for some models, check user and wireless passwords on the sticker)

When using a mobile application choose Quick setup and it will guide you through all necessary configurations in six easy steps.

Find your LR Gateway ID on the label within the product and register it in your Network Server.

To make the device connect to the LR Network Server.

Click the "Check for updates" button and update your RouterOS software to the latest version, the device needs to have an active Internet

connection.

After the update set your country, to apply country regulation settings.

Set your WiFi password.

Set the router password.

The following RouterOS "npk" packages are required for the core functionality of the product: lora, system.

Expansion slots and ports

10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for

connecting to other network devices.

External SMA antenna connector already connected to the LR card.

LED indicating a power state of the device.

LED Indicating the activity of Wireless network.

Automotive connector. Pinout: A - reserved for future use (orange), B - reserved for future use (blue), C - ground (black), D – power in (red).

MiniPCIe slot with integrated LR9 card.

Integrated Wireless module operating at 2.4 GHz, 802.11b/g/n protocol.

SIM slot.

Powering

The device accepts power in the following ways:

Ethernet port accepts passive PoE 9-30 V DC .

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 9-30 V DC.

Automotive connector 9-30 V DC.

The power consumption under maximum load can reach 7 W.

Connecting to a PoE Adapter:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.

Connect an Ethernet cable from your local network (LAN) to the PoE adapter.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Mounting

The device can be mounted in several ways: pole, wall, ceiling or it can be placed in specially designed Mikrotik holder which comes with the package. The

package also includes a drill hole template with detailed mounting instructions, to help you with the Ethernet cable installation and attachment to a ceiling

or a wall. Steel bracket to put on the other side of a dropdown ceiling tile and two screws and wall anchors. Zip ties or steel clamps for mounting on the

pole.