Mikrotik NetMetal ac² Handleiding

Mikrotik Niet gecategoriseerd NetMetal ac²

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik NetMetal ac² (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
1.
2.
NetMetal ac²
NetMetal ac²
NetMetal ac²
NetMetal ac²NetMetal ac²
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.
The Installation of the equipment must comply with local and national electrical codes.
This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate
measures.
Exposure to Radio Frequency Radiation:
Exposure to Radio Frequency Radiation:
Exposure to Radio Frequency Radiation:
Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an
uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the
general public.
Quickstart
The configuration is the same as PTP Bridge in AP mode, except that wireless mode is set to ap_bridge for PTMP setups. The router can be accessed
directly using the address. If the device is connected to the network with enabled DHCP server, configured DHCP client on the bridge interface will get the
IP address, that can be used to access the router.
Please follow these quick steps to set up your device:
Open the upper cover (see " ");NetMetal ac²#Removing upper and bottom covers
Connect an external antenna to the SMA connector (see " ");NetMetal ac²#Antenna usage
Open the bottom cover (see " ");NetMetal ac²#Removing upper and bottom covers
Connect your ISP cable to the device, make sure the ISP is allowing hardware change and will issue an automatic IP address;
Connect the device to the power source (see " ");NetMetal ac²#Powering
Open network connections on your PC and search for MikroTik wireless network and connect to it;
The configuration can be done through the wireless network usinga Web browser or configuration tool ;https://mt.lv/winbox
Once connected to the wireless network, open WinBox or Web browser;
The default IP: 192.168.88.1, user name: admin and there is no password (or, for some models, check user and wireless passwords on the
;sticker)
Once logged in, use Check For Update button to update the device to the latest software version, the device must have an active Internet
connection;
Once the device is updated, log in again and choose your country on the left side of the screen in the field "Country", to apply country regulation
settings;
Set antenna gain, depending on the antenna you are using,to ensure that EIRP meets the limit set by the local authorities;
Choose the security type WPA/WPA2 and insert a wireless password;
Set a password for your device,it will be used to login next timeand click Apply Configuration.
Powering
The device accepts power in the following ways:
Ethernet port accepts PoE 802.3af/at 24-57 V DC ;
Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.
Connecting to a PoE Adapter:
Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter;
Connect an Ethernet cable from your local network (LAN) to the PoE adapter;
3.
1.
2.
3.
4.
5.
6.
1.
2.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.
MikroTik mobile app
Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.
Scan QR code and choose your preferred OS.
Install and open application.
By default, the IP address and user name will be already entered.
Click Connect to establish a connection to your device through a wireless network.
Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps.
An advanced menu is available to fully configure all necessary settings.
Removing upper and bottom covers
To remove the upper cover, unscrew two captive screws and slide it off the main body. Do not remove screws completely, when assembling
tightening torque 0.2 Nm.
To remove the bottom cover, release clips for both fasteners and cover will be free to open.
Mounting
The NetMetal ac2 is designed to be used outdoors and mounted on pole or DIN rail.
When mounting, please ensure that cable feed is pointing downwards.
The IP rating scale of this device is IP66. We recommend using Cat6 shielded cables.
Warning! This equipment should be installed and operated with a minimum distance of 20 cm between the device and your body. Operation of this
equipment in the residential environment could cause radio interference.
Mounting and configuration of this device should be done by a qualified person.
The mounting hose clamp is provided with the package.
1.
2.
3.
Guide hose clamp through the opening on the back of the device.
Attach to the pole or mast.
Align and secure by hose clamp screw using PH2 screwdriver.
The device should be always placed by TOP cover facing upwards.
When mounting on DIN rail, please find a special bracket in the package and secure it with four screws to the back of the unit.
With the attached mounting bracket you will be able to slide the device on the DIN rail.

Product specificaties

Merk: Mikrotik
Categorie: Niet gecategoriseerd
Model: NetMetal ac²

Heb je hulp nodig?

Als je hulp nodig hebt met Mikrotik NetMetal ac² stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Mikrotik

Mikrotik

Mikrotik LtAP LR8 LTE6 kit Handleiding

25 April 2024
Mikrotik

Mikrotik Woobm-USB Handleiding

12 Maart 2024
Mikrotik

Mikrotik CME22-2n-BG77 Handleiding

16 November 2023
Mikrotik

Mikrotik hAP ac³ Handleiding

29 Augustus 2023
Mikrotik

Mikrotik L009UiGS-2HaxD-IN Handleiding

29 Augustus 2023
Mikrotik

Mikrotik hAP ax² Handleiding

29 Augustus 2023
Mikrotik

Mikrotik S-3553LC20D Handleiding

29 Augustus 2023
Mikrotik

Mikrotik hAP ax³ Handleiding

29 Augustus 2023
Mikrotik

Mikrotik hAP Handleiding

29 Augustus 2023
Mikrotik

Mikrotik hAP lite Handleiding

29 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024