Metra 107-UN02 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 107-UN02 (4 pagina's) in de categorie Carkit. Deze handleiding was nuttig voor 6 personen en werd door 3.5 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 12/7/20 INST107-UNO2
I N S TA L L AT I O N I N S T R U C T I O N S
107-UN02
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
Patent Pending
KIT FEATURES
KIT COMPONENTS
• A) Assembly mount • B) Display housing • C) Display trim ring • D) Display brackets • E) Display brackets (5-degree angle)
• F) (4) #8 x 1/2” Phillips screws • G) (4) 4mm Allen head screws
A B C D E
G
Floating Mount Kit Pioneer 6.8-inch
TOOLS REQUIRED
• Phillips screwdriver
• 4mm Allen head screwdriver
TABLE OF CONTENTS
Preface ....................................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
RGB Extension Cable: CD-RGB150E
(not sold by Metra)
F
The 107-UN02 is a universal mount
designed to “float” the Pioneer
6.8-inch screen in front of a vehicle’s
original radio location using a series
of brackets that provide the ability to
easily mount the radio’s chassis into
the radio/pocket location of more than
250 existing Metra Double-DIN kits for
1990 to current vehicle applications.
• Designed specifically for Pioneer
modular 6.8” radios like the
DMH-C2550NEX and DMH-C2500NEX.
• A complete housing encases
the Pioneer 6.8-inch screen
• Patent-pending design
1.800.221.0932
|
MetraOnline.com
2
PREFACE
• The 107-UN02 is designed to work with select newer Metra dash kits (sold separately). When
assembling the dash kit, follow the instructions for an ISO DIN radio provision with pocket.
a) The 107-UN02 will take place of the pocket provided with the dash kit.assembly mount
b) The Pioneer radio chassis will take place of the aftermarket radio.
• The 107-UN02 can be installed in many different configurations to fit many applications,
and can also be customized to take adjustments even further. Careful consideration must
be taken ahead of time before assembling the kit. Items to consider are the angle of the
factory radio and dash, the depth of the radio opening, and items which may be blocked by
the radio display or interfere with it.
• The cable from the radio chassis to the radio display may not be long enough in certain
installations. It is highly recommended to purchase an RGB extension cable from Pioneer,
part number CD-RGB150E.
• As laid out and shown in Kit Components, the will Assembly mount: assembly mount
mount into the lower portion of the dash kit, and the radio chassis will mount above that.
The can be flipped 180-degrees to allow more room above in certain assembly mount
installations where upper sub-dash depth is an issue. There is also play in the mounting legs
to allow depth adjustments into the dash. New holes can also be drilled into the legs to take
this play even further if necessary.
• Display Brackets: Two different brackets are provided to compensate for different dash
angles. If the dash is angled, use the 5-degree brackets. Washers (not provided) can
also be used if more than a 5-degree angle is necessary. The brackets can also be flipped
180-degrees to allow the display screen to sit higher.
• When attaching the Display Housing: display housing display brackets to the , use the
upper mounting holes to place the display screen higher if necessary.
REV. 12/7/2020 INST107-UNO2
3
KIT ASSEMBLY
Note: For steps 2 and 6, reference the
installation manual provided with the radio
for which hardware to use. The display
screen and radio chassis use two different
types of screws.
1. Secure the display brackets to the
assembly mount using (4) Allen head
screws provided. (Figure A)
Note: The brackets have a locking pin on
them which must face outwards.
2. Secure the radio chassis to the Metra
dash kit using (4) screws supplied with
the radio. (Figure B)
3. assembly mount Secure the to the
Metra dash kit using (4) Phillips screws
provided. (Figure C)
4. Route the RGB display cable from the
radio chassis, through the opening in
the .assembly mount
5. Complete all instruction steps provided
with the Metra dash kit.
6. Secure the radio display to the display
housing using (4) screws supplied with
the radio. (Figure D)
7. Clip the onto the display trim ring
assembly. (Figure E)
8. Plug the RGB display cable into the
display, then slide and lock in place the
display housing display brackets to the .
(Figure F)
The locking pins can be pulled Note:
back to release the display housing.
(Figure A) (Figure D)
(Figure B) (Figure E)
(Figure C) (Figure F)
Product specificaties
| Merk: | Metra |
| Categorie: | Carkit |
| Model: | 107-UN02 |
Heb je hulp nodig?
Als je hulp nodig hebt met Metra 107-UN02 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Carkit Metra
3 Juni 2025
3 Juni 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
31 Maart 2025
17 November 2024
17 November 2024
17 November 2024
Handleiding Carkit
- Carkit Pioneer
- Carkit Silvercrest
- Carkit Pyle
- Carkit Konig & Meyer
- Carkit Alpine
- Carkit Renkforce
- Carkit Hamron
- Carkit Sony Ericsson
- Carkit Dymond
- Carkit THB
- Carkit Motorola
- Carkit Einhell
- Carkit Blaupunkt
- Carkit T'nB
- Carkit Perfect Choice
Nieuwste handleidingen voor Carkit
3 Juni 2025
2 Juni 2025
19 Mei 2025
31 Maart 2025
30 November 2024
17 November 2024
15 November 2024
30 Juli 2024
30 Juli 2024
19 Juni 2024