Jung LS 459 D1 S Handleiding
Jung
Niet gecategoriseerd
LS 459 D1 S
Bekijk gratis de handleiding van Jung LS 459 D1 S (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.6 sterren uit 2 reviews. Heb je een vraag over Jung LS 459 D1 S of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
KNX room controller LS TOUCH
16.12.20221 / 60024026401
KNX room controller LS TOUCH
Ref.-no.: L .. 459 D 1S .., .. 459 D 1S ..
L .. Z 459 BF D 1S .., L .. Z .. 459 BF D 1S ..
LC 459 D 1S ..
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, re or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and standards
which apply for SELV circuits.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Fig. 1: Device components
(1) Supporting frame
(2) LS TOUCH with integrated frame (LS 990)
(3) Proximity sensor
Fig. 2: Device components
(4) External sensor connection (optional)
(5) KNX connection
(6) Prog. LED
(7) Prog. button
1
2
3
4 5
6 7
GB
KNX room controller LS TOUCH
16.12.20222 / 60024026401
3 Function
System information
The device can be updated. Firmware can be easily updated.
The device is KNX Data Secure capable. KNX Data Secure oers protection against manipulation in building
automation and can be congured in the ETS project. Detailed specialist knowledge is required. A device certicate,
which is attached to the device, is required for safe commissioning. During mounting, the certicate must be removed
from the device and stored securely.
Planning, installation and commissioning of the device are carried out with the aid of the ETS, version 5.7.4 and
above.
Intended use
- Operating electrical loads (light switching, dimming, controlling blinds/shutters etc.)
- Displaying the status of systems and information (e.g. temperature and brightness)
- Measurement and feedback control of the room temperature
- Installation in ush box with dimensions according to DIN 49073
Product characteristics
- With integrated 1-gang frame of the LS 990 or LS ZERO design range. Not suitable for other design ranges or
multiple combinations.
- High-resolution IPS display
- Capacitive touch screen
- Max. 32 KNX operating functions (switching, dimming, controlling blinds, value transmitter, calling up moods, music
etc.)
- Integrated room temperature sensor
- Room temperature control with setpoint value specication
- Alarm function (optical and optionally acoustic)
- Max. 8 timer functions depending on time, astronomical clock or random
- Integrated proximity and brightness sensor
- Integrated bus coupling unit
- Connection of installation buttons or reed contacts possible
- Commissioning and support of KNX Data Secure with ETS from version 5.7.4
4 Information for electrically skilled persons
Mounting and electrical connection
DANGER
Electrical shock on contact with live parts in the installation environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the power and cover live parts in the area!
Mounting the supporting frame
• Mount the supporting frame (1) on an appliance box.
Note marking “Top”.
Use the box screws included.
Connecting the device
Fig. 3: Connecting the device
• Connect the KNX (5).
• Optionally, connect the external sensor (4).
KNX room controller LS TOUCH
16.12.20223 / 60024026401
Connecting the external sensor
Only one of the following sensors can be connected:
- external temperature sensor (art. no.: FF NTC)
- external switching contacts (e.g. installation buttons or reed contacts)
Observe the technical data:
- cable type (J-Y(St)Y 2×2×0.8)
- permissible cable length max. 25 m)
- number of external switching contacts (max. 20 in parallel or series connection)
Do not connect any external voltage.
Fitting the device
• Attach the device (2) to the supporting frame.
Dismantling the device
Fig. 4: Dismantling the device
The frame of the device is integrated. The device cannot be removed from the frame.
• Carefully detach the entire device from the supporting frame.
For this purpose, use the suction lifter (art. no.: W-HEBER) included with LS ZERO.
5 Commissioning
Switching on
After connecting, the device is switched on automatically.
Demo mode
After switching on, the demo mode is displayed if the device has not yet been programmed. In demo mode,
communication with the KNX system is not possible.
KNX Data Secure
Requirements:
- Safe commissioning activated
- FDSK entered/scanned or device certicate added
iDocument all passwords and store them securely.
LED display
Prog. LED (6) lights up red:
Programming mode is activated.
Programming mode
Program device:
• Press the Prog. button (7).
Alternatively, activate the programming mode in the “Settings” menu:
Main menu → Settings → KNX programming mode
Prog. LED lights up red.
• Load physical address into the device.
Programming mode is terminated.
Prog. LED goes out.
Product specificaties
| Merk: | Jung |
| Categorie: | Niet gecategoriseerd |
| Model: | LS 459 D1 S |
Heb je hulp nodig?
Als je hulp nodig hebt met Jung LS 459 D1 S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Jung
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
23 Mei 2025
15 Mei 2025
15 Mei 2025
15 Mei 2025
15 Mei 2025
Handleiding Niet gecategoriseerd
- Broan
- Valco Baby
- Rega
- ARC
- Ernesto
- Corsair
- Spelsberg
- Axa
- DeWalt
- Titanwolf
- Bogen
- Crystal Video
- PowerWalker
- H-Tronic
- Norton Clipper
Nieuwste handleidingen voor Niet gecategoriseerd
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025