Jablotron JA-80BT Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Jablotron JA-80BT (2 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Bluetooth adapter JA-80BT 1 / 2 MHY51900
Bluetooth adaptér JA-80BT
Bluetooth adaptér JA-80BT slouží pro bezdrátové propojení systémů řady JA-8x
případně JA-6x a PC s tímto rozhraním. V ústředně se interface připojuje do
konektoru digitální systémové sběrnice pomocí přiloženého kabelu. Na počítači
musí být instalován potřebný hardware a software pro Bluetooth komunikaci.
Postup párování adaptéru
1. Připojte JA-80BT do digitální systémové sběrnice na ústředně. Po připojení se
zařízení cca 15 sekund inicializuje což je signalizováno rychlým blikáním modré
signálky. Po ukončení inicializace signálka zhasne.
2. Na PC pomocí ovládacího programu pro Bluetooth zadejte „Vyhledávat BT
zařízení“. Pro detailnější postup se řiďte pokyny určené pro tento program.*
3. Po nalezení periferie „JA-80BT“ klikněte na „Spárování“ a po výzvě k zadání klíče
(bezpečnostní kód pro spojení) zadejte čtyřmístné číslo uvedené na štítku JA-
80BT (PIN).
4. Po spárování si počítač vytvoří virtuální COM port (např. COM5) pro přístup
programu ComLink
5. Spuštěním programu ComLink začne prohledávat všechny existující porty a pokud
nalezne aktivnĂ­ komunikaÄŤnĂ­ COM od JA-80BT tak se s nĂ­m spojĂ­. SpojenĂ­ je na
JA-80BT signalizováno trvalým svitem modré signálky.
6. Po ukončení programu ComLink nebo po přepnutí do Offline režimu se
komunikace přeruší a modrá signálka zhasne.
*Poznámka: postup párování se může lišit podle použitých ovladačů ve vašem PC.
Technické parametry
Konektor RJ-4
Napájení ze systémové sběrnice
Proudový odběr (klid / max.) 6 mA / 25 mA
Délka propojovacího kabelu k ústředně 1 m
Vestavěný dekodér převod dat JA-8X/6X na Bluetooth
Kompatibilita ComLink verze 60 a vyšší
Jablotron s.r.o. tímto prohlašuje, že teto výrobek JA-80BT je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními NV č. 18/2003Sb a směrnice 1989/336/ES.
Originál prohlášení o shodě je na www.jablotron.cz v sekci poradenství.
Poznámka: Výrobek, ačkoliv neobsahuje žádné škodlivé materiály, nevyhazujte do
odpadků, ale předejte na sběrné místo elektronického odpadu. Podrobnější informace na
www.jablotron.cz sekce PoradenstvĂ­.
Bluetooth adapter JA-80BT 1 / 2 MHY51900
Bluetooth adaptér JA-80BT
Bluetooth adaptér JA-80BT slouží pro bezdrátové propojení systémů řady JA-8x
případně JA-6x a PC s tímto rozhraním. V ústředně se interface připojuje do
konektoru digitální systémové sběrnice pomocí přiloženého kabelu. Na počítači
musí být instalován potřebný hardware a software pro Bluetooth komunikaci.
Postup párování adaptéru
1. Připojte JA-80BT do digitální systémové sběrnice na ústředně. Po připojení se
zařízení cca 15 sekund inicializuje což je signalizováno rychlým blikáním modré
signálky. Po ukončení inicializace signálka zhasne.
2. Na PC pomocí ovládacího programu pro Bluetooth zadejte „Vyhledávat BT
zařízení“. Pro detailnější postup se řiďte pokyny určené pro tento program.*
3. Po nalezení periferie „JA-80BT“ klikněte na „Spárování“ a po výzvě k zadání klíče
(bezpečnostní kód pro spojení) zadejte čtyřmístné číslo uvedené na štítku JA-
80BT (PIN).
4. Po spárování si počítač vytvoří virtuální COM port (např. COM5) pro přístup
programu ComLink
5. Spuštěním programu ComLink začne prohledávat všechny existující porty a pokud
nalezne aktivnĂ­ komunikaÄŤnĂ­ COM od JA-80BT tak se s nĂ­m spojĂ­. SpojenĂ­ je na
JA-80BT signalizováno trvalým svitem modré signálky.
6. Po ukončení programu ComLink nebo po přepnutí do Offline režimu se
komunikace přeruší a modrá signálka zhasne.
*Poznámka: postup párování se může lišit podle použitých ovladačů ve vašem PC.
Technické parametry
Konektor RJ-4
Napájení ze systémové sběrnice
Proudový odběr (klid / max.) 6 mA / 25 mA
Délka propojovacího kabelu k ústředně 1 m
Vestavěný dekodér převod dat JA-8X/6X na Bluetooth
Kompatibilita ComLink verze 60 a vyšší
Jablotron s.r.o. tímto prohlašuje, že teto výrobek JA-80BT je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními NV č. 18/2003Sb a směrnice 1989/336/ES.
Originál prohlášení o shodě je na www.jablotron.cz v sekci poradenství.
Poznámka: Výrobek, ačkoliv neobsahuje žádné škodlivé materiály, nevyhazujte do
odpadků, ale předejte na sběrné místo elektronického odpadu. Podrobnější informace na
www.jablotron.cz sekce PoradenstvĂ­.
Bluetooth adapter JA-80BT 2 / 2 MHY51900
The JA-80BT Bluetooth adapter
The JA-80BT Bluetooth adapter (interface) allows you to establish a wireless
connection between systems of the JA-8x series or the JA-6x series and PCs
equipped with Bluetooth connectivity. You can connect the adapter to the control
panel’s digital bus connector via an RJ cable supplied with the package. The
computer is assumed to have all the hardware/software installed necessary for
Bluetooth communication.
Pairing the adapter
1. Connect the JA-80BT to the control panel’s digital system bus. After being
connected, the device will initialise for about 15 seconds which is indicated by blue
LED flashing. (The LED stops flashing as soon as the initialisation period ends.)
2. Start a search for BT devices using the Bluetooth driver program running on your
PC. To do so, follow the driver’s instructions *.
3. After a “JA-80BT” device has been discovered, click the “Pairing” button. A dialog
box should appear which prompts you to type in a code – a connection security
code. Key-in the four digit PIN number which is printed on the label attached to the
JA-80BT adapter.
4. After the devices have been paired a virtual COM port (e.g. COM5) is created on
the computer. This port is accessible to the ComLink software.
5. On start-up, the ComLink application scans through all existing computer ports. If
an active JA-80BT COM port is found, ComLink starts to communicate via this
port. This communication is indicated on the JA-80BT by a blue LED being
constantly lit.
6. Exiting the ComLink application or switching to Offline mode will end
communication and turn the blue LED off.
*Note: The pairing routine may vary depending on the drivers installed on your PC.
Specifications
Connector RJ-4
Power supply from the digital bus
Consumption (standby / maximum) 6 mA / 25 mA
Control panel connection cable length 1 m
Built-in decoder data conversion of JA-8x/6x to Bluetooth
Compatibility ComLink version 60 and higher
FCC ID VL6JA80BT
Jablotron Ltd. hereby declares that the JA-80E is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s
authority to operate the equipment. The original of the conformity assessment can be found at
www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful materials we suggest you return
the product to the dealer or directly to the producer after use.
Bluetooth adapter JA-80BT 2 / 2 MHY51900
The JA-80BT Bluetooth adapter
The JA-80BT Bluetooth adapter (interface) allows you to establish a wireless
connection between systems of the JA-8x series or the JA-6x series and PCs
equipped with Bluetooth connectivity. You can connect the adapter to the control
panel’s digital bus connector via an RJ cable supplied with the package. The
computer is assumed to have all the hardware/software installed necessary for
Bluetooth communication.
Pairing the adapter
1. Connect the JA-80BT to the control panel’s digital system bus. After being
connected, the device will initialise for about 15 seconds which is indicated by blue
LED flashing. (The LED stops flashing as soon as the initialisation period ends.)
2. Start a search for BT devices using the Bluetooth driver program running on your
PC. To do so, follow the driver’s instructions *.
3. After a “JA-80BT” device has been discovered, click the “Pairing” button. A dialog
box should appear which prompts you to type in a code – a connection security
code. Key-in the four digit PIN number which is printed on the label attached to the
JA-80BT adapter.
4. After the devices have been paired a virtual COM port (e.g. COM5) is created on
the computer. This port is accessible to the ComLink software.
5. On start-up, the ComLink application scans through all existing computer ports. If
an active JA-80BT COM port is found, ComLink starts to communicate via this
port. This communication is indicated on the JA-80BT by a blue LED being
constantly lit.
6. Exiting the ComLink application or switching to Offline mode will end
communication and turn the blue LED off.
*Note: The pairing routine may vary depending on the drivers installed on your PC.
Specifications
Connector RJ-4
Power supply from the digital bus
Consumption (standby / maximum) 6 mA / 25 mA
Control panel connection cable length 1 m
Built-in decoder data conversion of JA-8x/6x to Bluetooth
Compatibility ComLink version 60 and higher
FCC ID VL6JA80BT
Jablotron Ltd. hereby declares that the JA-80E is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s
authority to operate the equipment. The original of the conformity assessment can be found at
www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful materials we suggest you return
the product to the dealer or directly to the producer after use.


Product specificaties

Merk: Jablotron
Categorie: Beveiliging
Model: JA-80BT

Heb je hulp nodig?

Als je hulp nodig hebt met Jablotron JA-80BT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Beveiliging Jablotron

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging