GE ZDIC150WBB Handleiding
GE
Ijsmachine
ZDIC150WBB
Bekijk gratis de handleiding van GE ZDIC150WBB (18 pagina’s), behorend tot de categorie Ijsmachine. Deze gids werd als nuttig beoordeeld door 53 mensen en kreeg gemiddeld 4.5 sterren uit 27 reviews. Heb je een vraag over GE ZDIC150WBB of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/18
Installation
Instructions
Automatic Ice maker
ZDIC150
ZDIS150
Design Guide
With Installation Instructions
monogram.com
Installation Instructions
• BEFORE YOU BEGIN:
Read these instructions completely and carefully.
• IMPORTANT:
Save these instructions for local inspector’s use.
• IMPORTANT:
Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded.
Failure to do so can result in death, fire or electrical
shock. See “Power Supply,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Le non-respect de ces instructions peut causer la
mort, un incendie ou un choc électrique. Consulter «
Alimentation électrique », page 6.
If you received a damaged ice maker, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
• Use this appliance only for its intended purpose.
Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,
electrical connections and grounding must comply
with applicable codes. In the absence of local codes,
the ice maker should be installed in accordance
with National Electrical Code ANSI/NFPA 70-1990 or
latest edition.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
2
CONTENTS
Design Information
Models Available .................................................................... 3
Optional Accessories ........................................................... 3
Tools and Materials Required ........................................ 3
Cutout & Product Dimensions .........................................4
Installation
Advance Planning .................................................................4
Water Supply ........................................................................... 5
Power Supply ........................................................................... 6
Remove Packaging ............................................................... 6
Water Filtration System ................................................. 6, 7
Adjust Height of Ice maker ...............................................7
Connect the Drain ................................................................. 9
Connect Water Supply to Appliance ............................9
Reverse Door Swing ...................................................10, 11
Accessories
ZPK2 Auxiliary Pump Kit ............................................ 12-15
ZIP75BB Kit for 3/4” thick panels ..........................16, 17
Design Information
MODELS AVAILABLE
ZDIC150ZBB, ZDIS150ZSS
Available in black and stainless steel.
The ice maker may be installed below a countertop
or used free-standing.
3
OPTIONAL ACCESSORIES
=,3%%³For the installation of a trimless
3/4” thick custom panel on black models (not for
stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of your choice may be installed onto
the 3/4” panel. See installation instructions
on pages 10 and 11.
ZPK2 Drain Pump Kit - For use when a floor drain is
not available. The drain pump must be installed
inside the unit and can pump discharge water at a
maximum vertical height of 10 feet. 10 feet of tubing
is supplied with the kit.
TOOLS AND MATERIALS REQUIRED FOR BASIC INSTALLATION
• 1/4” socket
• 3/4” adjustable wrench
• Level
• GE SmartConnect™ Refrigerator Tubing Kit or 1/4” O.D.
copper tubing, of sufficient length to reach the installation
• Flat-blade screwdriver
• 7/16” and 1/2” open-end wrenches or 2 adjustable wrenches
• 1/4” nut driver
Product specificaties
| Merk: | GE |
| Categorie: | Ijsmachine |
| Model: | ZDIC150WBB |
Heb je hulp nodig?
Als je hulp nodig hebt met GE ZDIC150WBB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Ijsmachine GE
27 Oktober 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
6 December 2023
13 Juni 2023
11 Mei 2023
4 Mei 2023
30 April 2023
Handleiding Ijsmachine
- Electrolux
- Boretti
- Ambiano
- Termozeta
- Hatsuyuki
- Nemox
- Krups
- Kalorik
- Zoku
- Pifco
- Sunbeam
- Gourmia
- Atosa
- H.Koenig
- Perlick
Nieuwste handleidingen voor Ijsmachine
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025