GE Profile PIP70SS Handleiding

GE Ijsmachine Profile PIP70SS

Lees hieronder de 📖 handleiding in het Nederlandse voor GE Profile PIP70SS (2 pagina's) in de categorie Ijsmachine. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca
Installation Stainless Steel
Instructions Door Panel
Installing the Stainless Steel Panel with Handle
The panel will be held on by 6 sheet metal screws and 2
machine screws.
1. Remove the gasket from the inside of the door and retain
for later use.
2. Remove any plastic covering the stainless steel panel.
3. Place the door panel onto the outside of the door and
secure it with 2 machine screws in the left center and right
center of the door.
4. Fasten the panel to the door using the 6 sheet metal
screws. In the hinge opening area opposite the hinge side,
use the outermost screw holes only.
5. Place the covers over the hinge opening areas and secure
each cover to the door using a sheet metal screw and
washer.
6. Insert hole plug over screw installed in step 5.
7. Return the gasket to its original position.
8. Attach the door to the cabinet using the original screws.
17-3590-01 31-49096-1 11-15 GE
Gasket Machine
Screw
Door
Panel
Use UPPER
hole at the top
Hole Plug Cover
Use LOWER
hole at the
bottom
GE
Appliances
Appliance Park
Louisville, KY 40225
GEAppliances.com
NOTE: If the door swing is going to be changed, please complete prior to installing the door panel per the directions in your Owner’s Manual.
¿Preguntas? Llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio Web en: GEAppliances.com
Instrucciones Panel de la Puerta
de Instalación de Acero Inoxidable
Instalación del Panel de Acero Inoxidable con Manija
El panel será sostenido por 6 tornillos para chapa metálica y
2 tornillos para metal.
1. Retire la junta del interior de la puerta o conserve la misma
para uso posterior.
2. Retire cualquier cobertura plástica que esté recubriendo el
panel de acero inoxidable.
3. Coloque el panel de la puerta sobre la parte exterior de la
puerta y asegure el mismo con 2 tornillos para metal en el
centro izquierdo y en el centro derecho de la puerta.
4. Ajuste el panel a la puerta usando 6 tornillos para chapa
metálica.En el área de apertura opuesta al lado donde se
encuentran las bisagras, use los agujeros para tornillos más
alejados únicamente.
5. Coloque las tapas sobre las áreas de apertura de las
bisagras y asegure cada tapa a la puerta usando un tornillo
para chapa metálica y una arandela
6. Inserte el tapón del orificio sobre el tornillo instalado en el
paso 5.
7. Vuelva a colocar la junta en su posición original.
8. Adhiera la puerta al gabinete usando los tornillos originales.
17-3590-01 31-49096-1 11-15 GE
Junta Tornillo para
Metal
Panel de
la Puerta
Use el agujero
SUPERIOR en
la parte más
alta
Tapón del
Orificio
Tapa
Use el
agujero
INFERIOR
en la parte
más baja
GE
Appliances
Appliance Park
Louisville, KY 40225
GEAppliances.com
NOTA: Si se modificará la apertura de la puerta, complete este paso antes de instalar el panel de la puerta. Lea la manual del propietario


Product specificaties

Merk: GE
Categorie: Ijsmachine
Model: Profile PIP70SS

Heb je hulp nodig?

Als je hulp nodig hebt met GE Profile PIP70SS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Ijsmachine GE

Handleiding Ijsmachine

Nieuwste handleidingen voor Ijsmachine