Eurolite LVH-6 Handleiding

Eurolite Controller LVH-6

Lees hieronder de 📖 handleiding in het Nederlandse voor Eurolite LVH-6 (4 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
www.eurolite.de
USER MANUAL
BEDIENUNGSANLEITUNG
LVH-6
VIDEO SWITCH
© Copyright
Nachdruck verboten!
Reproduction prohibited!
LVH-6
A UT OM AT I C VI D E O S W I T CH
LVH-6 VIDEO SWITCH
LVH-6
AU T O M AT I C VI D E O S WI T C H
Video signal from equipment [NTSC/PAL]
Videosignal von Videogerät [NTSC/PAL]
12-24 V DC
Slave output to control other units
Slave-Ausgang zur Steuerung anderer Geräte
Alternate video source
Alternative Videoquelle
Acceptor or 75 terminator plugW
Endgerät oder 75 AbschlussW
POWER
LVH-6 VIDEO SWITCH
AUTOMATIC VIDEO SWITCH 2:1
The LVH-6 was designed to switch video signals from two sources to one output. The unit
utilizes a high quality RF relay to automatically switch to an alternate source when the
primary signal is lost. The slave output allows for controlling other units. Power connections
are made using block terminals. The unit responds to NTSC and PAL signals.
SAFETY INSTRUCTIONS
• Before your initial start-up, please make sure that there are no transport damages. Should
there be any, do not take the device into operation and immediately consult your dealer.
• Operate the device only after having familiarized with its functions. Do not permit operation
by persons not qualified for operating the device.
• Protect the device against humidity and heat. Keep away from heaters and other
heating sources!
• We recommend a frequent cleaning of the device. Disconnect from mains first. Use
a soft lint-free and moistened cloth. Never use alcohol or solvents!
• There are no serviceable parts inside the device. Maintenance and service operations are
only to be carried out by authorized dealers.
• Damage, caused by manual modifications on the device are not subject to warranty. If the
device is used for other purposes than originally intended or if it is not correctly connected,
the product may suffer damages and the guarantee becomes void.
• This product is allowed to be operated with 12-24 V DC. This device falls under protection
class 3 and was designed for indoor use only.
OPERATION
Prior to connecting switch off all units and do not turn them on again until you have made all
necessary connections.
1 Connect your signal source via a 75 coaxial cable with BNC plugs to the jack INPUT.This
input is 75 terminated.
2 Connect an alternative signal source via a 75 coaxial cable with BNC plugs to the jack
AUX INPUT.This input is terminated when it is connected to the output and is unterminated
when it is not in use.
3 Connect the unit to which the video signal is to be switched via a 75 coaxial cable with
BNC plugs to the jack OUTPUT. The output is designed to connect to a 75 load.
4 To power the unit 12-24 V DC are required. For this purpose, connect a power source (e.g.
power supply unit, battery) to the terminals DC 12-24. Always observe the correct
polarity.Connect the marked core to the left contact "+".
5 To control another unit with the LVH-6 connect it to the terminal SLAVE.
6 When the LVH-6 detects a video signal the jack INPUT is connected to the jack OUTPUT.
The unit responds to valid NTSC or PAL sync while ignoring 50 Hz and 60 Hz hum related
to induction artifacts. Weak signals as low as 0.5 V can be detected. When a valid signal is
detected, the relay also provides a ground connection to the SLAVE terminal, permitting
the unit to be connected as a video presence detector.
7 In the absence of video input at the jack INPUT or if power to the unit is interrupted, the jack
AUX INPUTis connected to the jack OUTPUT.
TECHNICAL SPECIFICATIONS
Power supply: ..................12-24 V DC, 30 mA
2x video inputs: ................0.5-1 Vpp/75 BNC, ground referenced
1x video output:................BNC, ground referenced
Slave output:....................100 mA, block terminal
Dimensions (LxWxH): ......76 x 41 x 31 mm
Weight: ............................7 g
W
W
W
W
W
W
Please note: Every information is subject to change without prior notice. 20.01.2009 ©

Product specificaties

Merk: Eurolite
Categorie: Controller
Model: LVH-6

Heb je hulp nodig?

Als je hulp nodig hebt met Eurolite LVH-6 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Controller Eurolite

Eurolite

Eurolite LVH-1 Handleiding

18 Juni 2023
Eurolite

Eurolite DMX Operator 192 Handleiding

9 Juni 2023
Eurolite

Eurolite LVH-5 Handleiding

6 Juni 2023
Eurolite

Eurolite LVH-4 Handleiding

3 Juni 2023
Eurolite

Eurolite LVH-3 Handleiding

2 Juni 2023
Eurolite

Eurolite LVH-8 Handleiding

30 Mei 2023
Eurolite

Eurolite VSD-108 Handleiding

29 Mei 2023
Eurolite

Eurolite DMX Scene Setter 24/48 Handleiding

27 Mei 2023
Eurolite

Eurolite AVS-402 Handleiding

21 Mei 2023
Eurolite

Eurolite DPMX-1216 Handleiding

16 Mei 2023

Handleiding Controller

Nieuwste handleidingen voor Controller

HyperX

HyperX ChargePlay Clutch Charging Grips Handleiding

25 April 2024
Victrix

Victrix Pro FS-12 Handleiding

25 April 2024
Circle

Circle with Disney Handleiding

18 April 2024
Genesis

Genesis Mangan 200 Handleiding

16 April 2024
Genesis

Genesis Mangan 300 Handleiding

16 April 2024
Reely

Reely Sky-series-12A Handleiding

16 April 2024
Hori

Hori Tactical Assault Commander Handleiding

16 April 2024
BeamZ

BeamZ WTR10 Handleiding

15 April 2024
Datapath

Datapath VSN1182 Handleiding

8 April 2024
Datapath

Datapath VSN982 Handleiding

8 April 2024