EtherWAN EX71000 Handleiding

Bekijk gratis de handleiding van EtherWAN EX71000 (2 pagina’s), behorend tot de categorie Csavaros gép. Deze gids werd als nuttig beoordeeld door 10 mensen en kreeg gemiddeld 5.0 sterren uit 7 reviews. Heb je een vraag over EtherWAN EX71000 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

W70G-EX710V2Q3 Page 1

Copyright 2022 EtherWAN Systems, Inc. All Rights Reserved 12/06/2022

Installation Guide

EX71000 Series | Hardened Managed Ethernet Switch

Switch

Unpacking

Open the carton and unpack the items. Your package should include:

▪One EX71000 hardened managed switch

▪One console cable

If any items are missing or damaged, notify your EtherWAN representative. If

possible, save the carton and packing material in case you need to ship or store the

switch in the future.

What Else You Need

▪Category 5 or better cable for RJ-45 ports

▪Appropriate fiber cables for fiber ports

▪Appropriate SFP cable for SFP ports

▪Personal computer with a DB-9 straight cable

Select a Location

▪Indoor use only, DIN Rail, wall-mount, rack, or cabinet.

▪Installation altitude should be less than 2000 meters.

▪Identify a power source within 6 feet (1.8 meters).

▪Choose a dry area with ambient temperature between -40 and 75 ºC (-40

and 167ºF). Operational humidity range: 5% to 95%, non-condensation

▪The product is open type. Be sure there is adequate airflow. (in an enclosure

or industrial panel)

▪The Ethernet switch should be mounted in an industrial control panel with

ambient temperature not exceeding 75 degrees C.

Connect to the Data Ports

Depending on the model, your switch can have the following ports:

EX71802-0YB

8-port 10/100BASE-TX + 2-port Gigabit

EX71622-XYB

6-port 10/100BASE-TX + 2-port 100BASE-FX + 2-port Gigabit

EX71620-XYB

6-port 10/100BASE-TX + 2-port 100BASE-FX

EX71440-X0B

4-port 10/100BASE-TX + 4-port 100BASE-FX

Apply Power

The switch has a 12-48VDC terminal block for power input. Only one power input

is required to operate the switch. However, redundant power supply functionality

is supported.

Note: Use qualified power supply, either SELV, Class 2 or double insulated per UL

60950 or UL 61010-1 or UL 61010-2-201 standards.

Device power consumption: 0.72 A

Terminal Block

The terminal block has 8 terminal posts as shown.

Pin

Description

Power 1

+

12-48VDC

−

Power Ground

Power 2

+

12-48VDC

-

Power Ground

Earth Terminal

Relay

Relay Output

Rating

1A @250VAC

Relay Output Alarm

The switch provides relay output contacts for signaling of a user-defined power or

port failure. The relay output can be connected to an alarm signaling device.

Current is 1A at 250VAC.

Power-Up Sequence

When the switch is powered up:

▪All Link/ACT LEDs blink momentarily.

▪The Power 1 LED light goes ON.

▪LEDs for every port connected to a device will flash, as the switch conducts a

brief Power On Self-Test (POST).

LED Indicators

LED

Color

State

Description

Main System

Power 1 /

Power 2

Green

On

Power on

Off

Power Off

Alarm

Red

On

Power failure

Off

No power failure

100/1000Base-TX, 100Base-FX Interface

Link/Act

Green

On

ON = Network connection established.

Flashing = port sending or receiving data.

100

Orange

On

ON = valid port connection at 100 Mbps.

1000Base-SX/LX/BX LEDs

Link/Act

Green

On

ON = Network connection established.

Flashing = port sending or receiving data.

1000

Orange

On

ON = Port connection at 1000 Mbps.

Console Configuration

▪Connect to the switch console by connecting a DB-9 cable to the console

port of the switch and to the serial port of a computer running a terminal

emulation application (such as HyperTerminal or Putty).

▪Configuration settings of the terminal-emulator: Baud rate: 115,200bps,

Data bits: 8, Parity: none, Stop bit: 1, Flow control: none.

▪The default login name is “root,” no password.

Web Configuration

▪Log in to the switch by launching a web browser and entering 192.168.1.10

in the address bar.

▪Enter the default login ID: root (no password) and click “Login.”

Other information

DIN-Rail assembly, startup, and dismantling

Assembly: Place the Switch on the DIN rail from above using the slot. Push the

front of the Switch toward the mounting surface until it audibly snaps into place.

Startup: Connect the supply voltage to start the switch via the terminal block.

Dismantling: Pull out the lower edge and then remove the Switch from the DIN

rail.

Power wiring information:

▪Use cable type - AWG (American Wire Gauge) 18-24 and the corresponding

pin type cable terminals. Tighten terminal screws with a torque value of 1.7

lb-in (0.2Nm) . Do not use excessive force when fixing wiring.

▪Use copper conductors only

▪The rating of the power wire used must be at least 105°C.

Product specificaties