Draper 253219 projection screen 253219 Handleiding
Pagina's 2 Engels Projectiescherm
Bekijk de handleiding van Draper 253219 projection screen 253219 gratis online of download de PDF. Deze handleiding is 51 keer bekeken. Vraag over dit model? Stel een vraag
Assembly/Mounting Instructions
Onyx Permanently Tensioned Projection Screen by Draper
Caution
①Read instructions through completely before proceeding.
②Follow instructions carefully. Installation con trary to instructions
invalidates warranty.
③Screen should be accessible for complete removal should fabric
become damaged or should other ser vice be required.
④Screen should be installed level (using a carpenter’s level).
⑤Nothing should be fastened to screen frame or viewing surface.
⑥Make sure you have received all parts (see parts list below and
exploded diagram on page 2).
⑦Tools Required: Medium (#2) Phillips screwdriver (6" or greater shaft
length suggested). Optional tools: Flat blade screwdriver or small
putty knife.
⑧Installer is responsible for providing appropriate hardware for mounting.
⑨When lifting assembled screen, do not lift at only one corner; lift at
both corners. Lifting by one corner could result in damage to the
screen frame, especially on large screens.
⑩ The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Copyright © 2010 Draper Inc. Form Onyx_Inst10 Printed in U.S.A.
®
If you encounter any diffi culties installing or ser vic ing your Onyx screen, call your
dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.
Onyx—Hardware and Parts List
Frame Preparation
①Clean area and place frame assembly pieces face down. Insert plastic
corner pieces into ends of aluminum frame extrusions as indicated in
Figures 1 through 4. Secure each corner to each frame extrusion by
threading one #10-24 fastener through hole in plastic corner and into
rounded slot in aluminum frame extrusion.
Caution: Do not over-tighten fasteners—over-tightening could cause
damage to the frame corners.
Figure 1
②Secure corner pieces to aluminum frame extrusions with four (4) remaining
fasteners. Check to verify that all four (4) plastic corners are secure to
aluminum frame extrusion lengths and all eight (8) fasteners are tight (see
Fig. 5).
Caution: Do not over-tighten fasteners—over-tightening could cause
damage to the frame corners.
Figure 2
Frame Extrusions - 4
Frame Corners - 4
#10-24 fasteners - 8
Z-Brackets - 2
Viewing Surface - 1
Plastic Tubing - 4
Surface Retention
Extrusions- 4
Front
Back
Figure 3
Figure 5
Figure 4
(Continued on Page 2)
Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.
Caution: When lifting assembled screen, do not lift at only one corner; lift
at both corners. Lifting by one corner could result in damage to the screen
frame, especially on large screens.
Product specificaties
| Merk: | Draper |
| Categorie: | Projectiescherm |
| Model: | 253219 projection screen 253219 |
| Kleur van het product: | Black,White |
| Gewicht: | 29480 g |
| Oorspronkelijke beeldverhouding: | 16:9 |
| Zichtbare schermhoogte (h): | 2032 mm |
| Zichtbare schermbreedte (b): | 3556 mm |
| Diagonaal: | 161 " |
| Totale grootte van het scherm (hoogte x breedte): | 2235 x 3759 cm |
| Formaat: | HDTV |
| Grenzen: | 101.6 mm |
Heb je hulp nodig?
Als je hulp nodig hebt met Draper 253219 projection screen 253219 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden