Draper Cineperm Handleiding

Bekijk gratis de handleiding van Draper Cineperm (1 pagina’s), behorend tot de categorie Projectiescherm. Deze gids werd als nuttig beoordeeld door 52 mensen en kreeg gemiddeld 4.3 sterren uit 8 reviews. Heb je een vraag over Draper Cineperm of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Installation Instructions

Cineperm Permanently Tensioned Projection Screen by Draper

Copyright © 2011 Draper Inc. Form Cineperm_Inst11 Printed in U.S.A.

Frame Assembly

Standard Frame—

①Lay out frame pieces on fl oor, by matching up color-coded tape near

corners. Snaps should be facing up.

②Assemble frame (see Fig. 1). If nec es sary gently tap frame ends with a

rubber mallet to make sure castings are fully seated.

Surface Installation

①Carefully remove surface from cardboard tube and unroll onto a clean

cloth or paper.

②Engage snaps in each corner, then secure rest of screen snaps.

③Stretch fabric across frame. Use extreme caution when attaching fabric.

Overstretching or rough handling could cause the viewing surface to tear.

Frame Installation (Standard Frame)

Outside (Face) Mount—

①Drill mounting holes in frame (see Fig. 2).

②Mark wall and drill holes to correspond with those in the frame.

③Enlarge holes in frame side furthest from wall to allow screw heads to pass

through (see Fig. 2). Do not allow screw heads to remain outside the

frame: overtightening could bend frame and affect screen fl atness.

Cineperm

frame

Mounting hardware

by others

Viewing surface snaps to

frame, covering mounting holes

Supporting structure

Drill through frame for

mounting hardware.

Enlarge first hole for screw

head to pass through.

Figure 2

Figure 3

Inside (Jamb) Mount—

①Place frame assembly in opening to check for a snug fi t. If frame is too

large, opening may have to be enlarged. If frame is too small or does not

sit square in the opening, shims and caulking may be required.

②Drill mounting holes in frame, and enlarge the fi rst holes to allow screw

heads to pass through (see Fig. 3). Do not allow screw heads to remain

outside the frame: overtightening could bend frame and affect screen

fl atness.

③Drill holes in jamb.

④Attach frame using appropriate fasteners for mounting surface (provided

by others).

⑤Use caulk to ensure there is no light leakage around edges of frame.

Truss Frame—

①Unfold and lay out pieces on fl oor, by matching up color coded marks.

Lock all hinges (see Fig. 1). Stage Left and Stage Right sections should be

placed with snaps . Top and bottom sections should be placed with up

snaps down.

② To increase frame rigidity, hinges on top and bottom sections have rivnuts

marked with red and green. Insert a Handy Crank through the threadless

rivnut (red) and tighten into the threaded rivnut (green).

③Apply small sections marked “Stiffener Bars” to back of bottom frame

section, using 8 Handy Cranks. These eliminate sag on large suspended

frames. Failure to use all Handy Cranks may result in screen frame

damage. Turn bottom frame section over so snaps face up.

④Repeat step 3 for top frame section.

⑤Join top and bottom sections to Stage Left and Stage Right, using 2

Handy Cranks on each of the 4 corners. Match numbers on white labels.

NOTE: No Handy Crank should protrude outside screen frame.

⑥Attach surface (see “Surface Installation”), and suspend using appropriate

materials (provided by others to meet specifi c installation requirements).

Opening

Wall

Anchor bolt by others.

Clearance hole in outer

wall by others.

Snap-on viewing surface

1" square

alum. tube

Wall

Anchor bolt by others.

Clearance wall in outer

wall by others.

Locate between snaps.1 square

alum. tube

Snap-on viewing surface

Inside (Jamb) Mount

Outside (Face) Mount

④Attach frame to wall using appropriate fasteners for mounting surface

(provided by others).

NOTE: Measure screen frame width at the top, bottom, and center; Make

sure the frame is installed so the center width is same as the width at

the top and bottom.

Figure 1

Standard FrameTruss Style Frame

Caution

①Read instructions through completely before pro ceed ing.

②Follow instructions carefully. Installation con trary to instructions

invalidates warranty.

③Bent or warped frames will affect surface fl atness and image quality.

④Screen should be square, and width should not vary from the center to

the ends of the frame

⑤When lifting assembled screen, do not lift at only one corner; lift at both

corners. Lifting by one corner could result in damage to the screen

frame, especially on large screens.

⑥Screen should be installed level (using a carpenter’s level).

⑦Nothing should be fastened to screen frame or viewing surface.

⑧Be careful not to rip screen material when attaching surface to frame.

⑨The ideal temperature range for assembling this screen to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

NOTE: Screen has been inspected and tested at factory prior to shipment.

Jamb of opening

Viewing Surface snaps to

frame, covering mounting holes

Cineperm

frame

Drill through frame for

mounting hardware. Enlarge

first hole for screw head

to pass through.

Mounting hardware

by others

Color-coded

tape

®

Handy

Cranks

If you encounter any diffi culties installing or servicing your Cineperm, call your

dealer or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.

Always fold viewing surface with snaps face-to-face.

Do not permit screen fabric to contact border material

or snaps when folded. Store in pouch provided.

Product specificaties