Elite Screens CineTension2 TE100HW2 Handleiding

Elite Screens Projectiescherm CineTension2 TE100HW2

Lees hieronder de 📖 handleiding in het Nederlandse voor Elite Screens CineTension2 TE100HW2 (6 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

Rev.062916-DR www.elitescreens.com

Tab-tensioned Electric Motorized Projection Screen

CineTension 2 Series

User’s Guide

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra

Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.

Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this

unit are prohibited and will void your warranty. For more information, please contact our Technical

Support Department at (877) 511-1211 Ext. 604.

 Please retain this user’s guide for future reference.

 To avoid damaging the unit, do not use with any unauthorized accessories not recommended by

the manufacturer.

 Handle the unit carefully during transportation to avoid any damages.

 To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

 The power outlet supplying power to the unit should be close to the unit and easily accessible.

 Do not install the unit on uneven, inclined surfaces;

 Do not install in damp places to avoid an electric shock or short circuit.

 Do not place any heavy objects over the power cord.

 Position the power cord properly to avoid creating a trip obstacle.

 To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the

power cord.

 The internal & external parts of this unit are not end user serviceable. Do not attempt to

disassemble this unit by yourself. No one except authorized technicians can open and make

repairs to this unit.

 Make sure the power source that this unit is connected to has a continuous power flow.

 If there is need to use an extension cord, make sure the cord has an equal rating as the appliance

to avoid over heat.

 Do not handle the power plug when your hands are wet or your feet are in contact with water.

 Properly dispose of this equipment according to the environmental regulations in your area when

product is no longer of service.

Rev.062916-DR www.elitescreens.com

Do not use this unit under the following circumstances.

 Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.

 Avoid direct sun light, rain shower and moisture.

 Keep away from fire sources and high temperature to prevent this device from overheating.

 Cut off the power supply first before transportation or maintenance.

 To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious

damage or if there are any evident broken parts.

Installation Warning

The instructions provided in this user’s guide are for reference only. Please consult a professional

installation company for further installation and safety advice. The installer must insure that

proper mounting hardware is used to provide adequate strength suitable for the installation. Elite

Screens is not liable for any faulty installations. For limit adjustment instructions, please contact

our Technical Support Department at (877) 511-1211 Ext. 604

The Screen’s is already set to its maximum drop distance. There is extra top black Top Black Drop NO

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.

Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures.

 Reorient or relocate the receiving antenna of the device which may be casing the

interference.

 Increase the separation between the screen and the device’s receiver.

 Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure

the fasteners that are used are of adequate strength and suitable for the installation location.

Rev.062916-DR

way Wall

switch

CineTension 2 Series| Controls and Accessories

A. IR Remote

E. IR extended “eye” receiver

F. W

Screen operation

Electric Current:

Depending upon

1. After ensuring the power

outlet &

outlet.

2. Once the screen

has power, you’l

6 ways to control your

CineTension 2

1. (IR remote control

Item A, Fig 1

of sight contact with a beam range of 3

circular window located on the left sid

2. Item E, Fig 2IR “Eye” Receiver (

directly into the screen’s RJ-

45 input to

control option for your IR remote contr

installation.

3. Item BRF Remote Control ( ):

The

direct line of sight with a range of 100

4. 3-Way Wall Switch (

Item C, Fig

mount control box with an up/stop/dow

screen’s RJ-45 input.

CineTension 2 Series| Controls and Accessories

B. RF Remote C. Wall switch control box

Wireless 5

-12v (3.5 mm)

mono

trigger cable

G. AAA batteries

region, your Elite Screen will operate on 100v, 110

& screen are compatible (

voltage), plug

the power c

ll be able to control it using any of the 6 methods des

IR “Eye” Receiver

The Infrared functions by direct

line

30 feet. Aim the IR remote at the

e of the screen

The IR “Eye” Receiver plugs

o present a low pr

ofile line-of-sight

rol even in a

recessed ceiling

radio waves eliminate the need for a

feet.

3): The 3-way wall switch is a wall

wn button and plugs directly into the

ig.

www.elitescreens.com

D. 5

-12 volt trigger cable

H. Bubble leveler

v, or 220v voltage.

cord into the power

scribed below.

STOP

DOWN

Fig.1

IR/RF remote

Fig.2

Product specificaties

Merk:	Elite Screens
Categorie:	Projectiescherm
Model:	CineTension2 TE100HW2
Kleur van het product:	Wit
Gewicht:	- g
Oorspronkelijke beeldverhouding:	16:9
Zichtbare schermhoogte (h):	1245 mm
Zichtbare schermbreedte (b):	2214 mm
Diagonaal:	100 "
Totale grootte van het scherm (hoogte x breedte):	- cm
Schermgain:	1.1