DLS RA 10 Handleiding

DLS Autoradio/CD speler RA 10

Lees hieronder de 📖 handleiding in het Nederlandse voor DLS RA 10 (12 pagina's) in de categorie Autoradio/CD speler. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12

How to install and

operate the DLS

Reference series

car audio mono

amplifier RA10.

Welcome!

This owners manual is written in easy english and

uses a lot of drawings to simply the installation and

use of the above amplifiers.

Your DLS amplifiers must be installed correctly in

order to work well. This manual will show you how

to install the amplifier like a pro. Please read the

entire manual before beginning the installation.

Install the amplifier yourself if you feel confident with

our instructions and if you have the proper tools.

However if you feel unsure, turn over the installa-

tion job to someone better suited to it.

Warranty Service

This amplifier is covered by warranty, depending

on the conditions in the country where it is sold. If

the amplifier is returned for service, please include

the original dated receipt with the product.





Technical Assistance

For technical assistance ask the shop where the

product was sold or the distributor in your very coun-

try.

You can always phone the DLS Helpdesk in Sweden

+ 46 31 84 00 60 or send an e-mail to info@dls.se.

Information can also be found on our WEB-site

www.dls.se

Contents

Features…………………………….. 2

Installation…………………….……. 2

Tools and materials needed………. 3

Amplifier installation kit………….... 3

Routing Wires…………………….... 3

Wiring:

Power connection..……………..…. 4

Input and controls………………..... 5

Input wiring..................................... 5

Input level control.......................... 6

Grand Bass..................………….... 6

Phase control................................. 6

Crossovers..................................... 6

RA10 speaker wiring:

One subwoofer…...……………….... 7

Two subwoofers...…………………... 7

Four subwoofers............................... 7

Installation with two subwoofers:

Wiring example.............................. .. 8

Testing……………………………….. 9

Troubleshooting……………………... 9

Professional tips…………………….. 10

Specifications………………………... 11

The amplifier include

RCA inputs

High Level input

Variable low pass crossover

Subsonic filter

Grand bass feature 0 - +18 dB

Phase shift continously variable 0-180 degr.

Remote bass level and phase shift control

Remote turn on / off

Automatic remote turn on/ off on high level

input without connecting any remote wire

Built-in cooling fan

Electronic protection circuitry against

short-circuit, DC offset and thermal overload.

Installation

Before you begin installation

Before you begin you need to read the manual, to have

some tools, cables and other material available. There

is one such list of material on the following page.

Amplifier location

Important

Allow air circulation around the amplifier.

Disconnect Battery

Before starting the instal-

lation, always disconnect

the negative terminal of

the battery.

The DLS Reference series of amplifiers have a

compact design that allows great flexibility in

mounting. You can mount it under a seat or in the

trunk. When you select a location, do remember

that the amplifier generates a lot of heat.

Choose a location where air can circulate freely

around the amplifier. Do not cover the amplifier

with carpets or hide behind trim panels.

Do not mount the amplifier in an inverted or upside

down position. The amplifier has a built-in fan

in the bottom plate. Mount the amplifier on

spacers to allow the air to circulate inside the

amplifier.

Check all locations and placements carefully

before making any cuts, drilling any holes or ma-

king any connections.

This is the best direction to

mount the amplifier in order

to get the best cooling.

RA10

DLS logo on amplifier cooling flange

The DLS logo on top of the amplifier is attached

with two hex. screws. The logo can be removed

and twisted 90 or 180 degrees, and then screwed

back in wanted position. The logo can be mounted

in four different ways to match your installation.

Tools and material needed

Tools:



Flat and Phillips screwdrivers



Wire cutter



Wire stripper



Electric drill with drills



Crimping tool



Digital multimeter or test lamp



Wire brush, scraper or a piece

of an abrasive sheet to remove

paint for a good ground connection

Grease to protect the ground

connection from oxidation

Material:

Speaker wire: minimum

12 AWG = 4 mm2 for subwoofer connection

Sheet metal screws for mounting the

amplifier to the amplifier board and the

amplifier board to the car + some extra

for fuse holder, amplifier ground etc.



Electrical insulation tape

½ inch thick plywood or particle board for

the amplifier to be mounted upon.

Amplifier installation kit:

If available,buy an amplifier installation kit. It

contains normally all you need. This is what you

have to buy if you buy the items separately

20- 25 feet = 6- 7.5 meter power cable,

4 AWG = 21 mm2 or heavier.

1 pc of fuseholder to install close to the

car battery + fuse 100 Ampere (for 4AWG

power cable).

20 feet of 15 AWG = 1,5 mm2 wire for

remote turn on / off cable from radio.

RCA-cable for input from radio.

- 20 feet or 5 meter for trunk installations

-12 feet or 2 – 3 meter for under seat

installations

Two ring crimp terminals –one

for connection to the battery plus and one

for the amplifier ground connection.

Four splicers to connect speaker

cables to high level input cable, if high level

input is used.

Wire ties

Insulating grommet or insulating tube

Stereo

head unit

Routing wires

RA10

Professional Tip:

Gauge (ga) is an American measure for cable size,

also called AWG (American Wire Gauge).

CONVERSION GAUGE - mm2

0 AWG = 50 mm2

1 AWG = 42 mm2 9 AWG = 6,8 mm2

2 AWG = 33 mm210 AWG = 5,3 mm2

3 AWG = 27 mm211 AWG = 4,2 mm2

4 AWG = 21 mm212 AWG = 3 mm2

5 AWG = 16 mm213 AWG = 2,7 mm2

6 AWG = 13 mm214 AWG = 2 mm2

7 AWG = 10 mm215 AWG = 1,65 mm2

8 AWG = 8 mm216 AWG = 1,3 mm2

Professional Tip:

If amplifier installation kits are available with diffe-

rent size of power cable, chose the most heavy

power cable to improve sound quality and to allow

more amplifiers to be installed now or later.

If possible use 4 AWG = 21 mm2 cable for best

performance. This is for cable lengths up to 5 me-

ters. The ground cable must have the same size.

Max fuse values for different cable sizes:

6 mm2 (9 AWG) :25 A 10 mm2 (7AWG) :40 A

16 mm2 (5AWG) :60 A 21 mm2 (4AWG) :100 A

33 mm2 (2AWG) :150 A 42 mm2 (1AWG) :200 A

Product specificaties

Merk:	DLS
Categorie:	Autoradio/CD speler
Model:	RA 10

Heb je hulp nodig?

Als je hulp nodig hebt met DLS RA 10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autoradio/CD speler DLS

DLS REFERENCE RA20 Handleiding

22 Augustus 2023

DLS RA 10 Handleiding

22 Augustus 2023

DLS CAD 15 Handleiding

22 Augustus 2023

22 Augustus 2023

22 Augustus 2023

22 Augustus 2023

22 Augustus 2023

Handleiding Autoradio/CD speler

Nieuwste handleidingen voor Autoradio/CD speler

Belson BS12100 Handleiding

31 Augustus 2023

Mx Onda MX1500 Handleiding

6 Augustus 2023

Belson BS12150 Handleiding

31 Augustus 2023

Belson BS11900 Handleiding

31 Augustus 2023

Belson BS11520 Handleiding

31 Augustus 2023

Mx Onda HUESCA Handleiding

6 Augustus 2023

Mx Onda BAEZA Handleiding

6 Augustus 2023

Mx Onda T825M Handleiding

6 Augustus 2023

Mx Onda T815M Handleiding

6 Augustus 2023

Mx Onda SALAMANCA Handleiding

6 Augustus 2023