DLS CA22 Handleiding

DLS Autoradio/CD speler CA22

Lees hieronder de 📖 handleiding in het Nederlandse voor DLS CA22 (16 pagina's) in de categorie Autoradio/CD speler. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16

How to install and operate the DLS

Performance series CA22, CA23,

CA31, CA41 and CA51 car audio

amplifiers.

Welcome!

This owners manual is written in easy english and

uses a lot of drawings to simply the installation and

use of the above amplifiers.

Your DLS amplifiers must be installed correctly in

order to work well. This manual will show you how

to install the amplifier like a pro. Please read the

entire manual before beginning the installation.

Install the amplifier yourself if you feel confident with

our instructions and if you have the proper tools.

However if you feel unsure, turn over the installa-

tion job to someone better suited to it.

Warranty Service

This amplifier is covered by warranty, depending

on the conditions in the country where it is sold. If

the amplifier is returned for service, please include

the original dated receipt with the product.





Technical Assistance

For technical assistance ask the shop where the

product was sold or the distributor in your very coun-

try.

You can always phone the DLS Helpdesk in Sweden

+ 46 31 84 00 60 or send an e-mail to info@dls.se.

Information can also be found on our WEB-site

www.dls.se

Contents

Features…………………………….. 2

Installation…………………….……. 2

Tools and materials needed………. 3

Amplifier installation kit………….... 3

Routing Wires…………………….... 3

Wiring

Power and Outputs……………..…. 4

Inputs and controls………………... 5

Input level control......................... 6

Grand Bass,Crossovers………….... 6

CA 31, CA 41, CA 51 Crossovers… 7

CA 22 and CA 23 speaker wiring:

Front speakers…...……………….... 8

Subwoofer…………………………... 8

CA 31 speaker wiring:

Front speakers…...……………….... 9

Subwoofer…………………………... 9

CA 41 speaker wiring:

Four speakers…………………….... 10

Two speakers + bridged subwoofer. 10

Two way front system with

active crossovers……………………. 11

CA 51 speaker wiring:

Four speakers…………………….... 12

Subwoofer...................................... 12

Testing……………………………….. 13

Troubleshooting……………………... 13

Professional tips…………………….. 14

Specifications………………………... 15

All models include

RCA inputs

High Level input

Continuos variable low pass and/or high

pass crossover

Bass boost feature (only on CA23 & CA41)

Remote turn on / off

Automatic remote turn on/ off on high level

input without connecting any remote wire

Electronic protection circuitry against

short-circuit, DC offset and thermal overload.

Bridgeable design to direct full power to

one or two subwoofers etc.

Installation

Before you begin installation

Before you begin you need to read the manual, to have

some tools, cables and other material available. There

is one such list of material on the following page.

Amplifier location

Important

Allow air circulation around the amplifier.

Disconnect Battery

Before starting the instal-

lation, always disconnect

the negative terminal of

the battery.

The DLS Performance series of amplifiers have a

compact design that allows great flexibility in

mounting. You can mount it under a seat or in the

trunk.

When you select a location, do remember that the

amplifier generates a lot of heat.

Choose a location where air can circulate freely

around the amplifier. Do not cover the amplifier

with carpets or hide behind trim panels.

Do not mount the amplifier in an inverted or upside

down position.

Check all locations and placements carefully

before making any cuts, drilling any holes or ma-

king any connections.

This is the best way to

mount the amplifier to get

the best cooling.

CA22, 23, 31, 41 & 51

CA22

2 x 60 Watt RMS / 2 x 100 Watt max in 2 ohm

1x 200 Watt RMS bridged

CA23

2 x 135 Watt RMS / 2 x 200 Watt max in 2 ohm

1 x 400 Watt RMS bridged

CA31

2 x 65 Watt RMS / 2 x 90 Watt max in 2 ohm

1 x 170 Watt RMS bridged

1 x 170 W RMS on sub channel

CA41

4 x 70 Watt RMS / 4 x 125 Watt max in 2 ohm

2 x 200 Watt RMS bridged

CA51

4 x 50 Watt RMS / 4 x 80 Watt max in 2 ohm

2 x 150 Watt RMS bridged

1 x 170 Watt RMS on sub channel

All above RMS power ratings with 4 ohm load

at 13,8 Volt DC.

DLS logo on amplifier cooling flange

The DLS logo on top of the amplifier is attached

with two 1 mm hex. screws. The logo can be remo-

ved and twisted 90 or 180 degrees, and then

screwed back in wanted position. The logo can be

mounted in four different ways to match your in-

stallation.

Removal of side flanges

In order to fasten the amplifier to the surface and

connect speaker and power cables, the flanges on

the sides must be removed. This is done by

loosening the hex screws on top of the amplifier.

Use a 3 mm hex key.

Remove these

screws using a 3

mm hex. key for

removal of side

flange. Remount

after fastening the

amplifier and

connection of the

speaker and power

cables.

Tools and material needed

Tools:



Flat and Phillips screwdrivers



Wire cutter



Wire stripper



Electric drill with drills



Crimping tool



Digital multimeter or test lamp



Wire brush, scraper or a piece

of an abrasive sheet to remove

paint for a good ground connection

Grease to protect the ground

connection from oxidation

Material:

Speaker wire: minimum

12 AWG = 4 mm2 for subwoofers

13 – 16 AWG = 1,5-2,5 mm2 for other

speakers

Sheet metal screws for mounting the

amplifier to the amplifier board and the

amplifier board to the car + some extra

for fuse holder, amplifier ground etc.



Electrical insulation tape

½ inch thick plywood or particle board for

the amplifier to be mounted upon.

Amplifier installation kit:

If available,buy an amplifier installation kit. It

contains normally all you need. This is what you

have to buy if you buy the items separately

20- 25 feet = 6- 7.5 meter power cable,

minimum AWG 8 = 10 mm2 or heavier

1 pc of fuseholder to install close to the

car battery + fuse 50 Ampere.

20 feet of AWG 15 = 1,5 mm2 wire for

remote turn on / off cable from radio.

RCA-cable for input from radio.

- 20 feet or 5 meter for trunk installations

-12 feet or 2 – 3 meter for under seat

installations

Two ring crimp terminals –one

for connection to the battery plus and one

for the amplifier ground connection.

Two heavy fork crimp terminals to connect

+ and – to amplifer – but you do only need

them if you use heavy cable or to make the

installation look nicer.

Four to ten fork crimp terminals to

connect the speaker cables – but you do

only need them if you use heavy cables or

want the installation to look nicer.

One fork crimp terminal to connect the

remote wire to the amplifier, but you need it

only to make it look nicer.

Four to eight splicers to connect speaker

cables to high level input cable, if high level

input is used.

Wire ties

Insulating grommet or insulating tube

Routing wires

Stereo

head unit

Professional Tip:

If amplifier installation kits are available with diffe-

rent size of power cable, chose the most heavy

power cable to improve sound quality and to allow

more amplifiers to be installed now or later.

If possible buy AWG 4 = PL 21 mm2 cable for best

performance.

These are the minimum sizes we recommend for

the different models:

CA22 10 mm2 (7AWG)

CA23 16 mm2 (5AWG)

CA31 21 mm2 (4AWG)

CA41 21 mm2 (4AWG)

CA51 21 mm2 (4AWG)

This is for cable lengths up to 5 meters.

The ground cable must have the same size.

CA22, 23, 31, 41 & 51

Product specificaties

Merk:	DLS
Categorie:	Autoradio/CD speler
Model:	CA22

Heb je hulp nodig?

Als je hulp nodig hebt met DLS CA22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autoradio/CD speler DLS

DLS REFERENCE RA20 Handleiding

22 Augustus 2023

DLS RA 10 Handleiding

22 Augustus 2023

DLS CAD 15 Handleiding

22 Augustus 2023

22 Augustus 2023

22 Augustus 2023

22 Augustus 2023

22 Augustus 2023

Handleiding Autoradio/CD speler

Nieuwste handleidingen voor Autoradio/CD speler

Belson BS12100 Handleiding

31 Augustus 2023

Mx Onda MX1500 Handleiding

6 Augustus 2023

Belson BS12150 Handleiding

31 Augustus 2023

Belson BS11900 Handleiding

31 Augustus 2023

Belson BS11520 Handleiding

31 Augustus 2023

Mx Onda HUESCA Handleiding

6 Augustus 2023

Mx Onda BAEZA Handleiding

6 Augustus 2023

Mx Onda T825M Handleiding

6 Augustus 2023

Mx Onda T815M Handleiding

6 Augustus 2023

Mx Onda SALAMANCA Handleiding

6 Augustus 2023