Curtis 1627 Handleiding
Curtis
Batterij-oplader
1627
Bekijk gratis de handleiding van Curtis 1627 (5 pagina’s), behorend tot de categorie Batterij-oplader. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.0 sterren uit 2 reviews. Heb je een vraag over Curtis 1627 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/5
Curtis Models 1622, 1626, and 1627
Battery Charger
Manual
53100 Rev A 1/17
Specifications are subject to change without notice.
© 2017 Curtis Instruments, Inc. ® Curtis is a registered trademark of Curtis Instruments, Inc.
© The design and appearance of the products depicted herein are the copyright of Curtis Instruments, Inc.
Read Instructions Carefully!
Curtis Instruments, Inc.
200 Kisco Avenue
Mt. Kisco, NY 10549
www.curtisinstruments.com
iiCurtis Models 1622, 1626, and 1627 Manual
TABLE OF CONTENTS
1.0 Important Safety and Operating Instructions .......................................1
Safe Operating Instructions ...................................................................2
2.0 Understanding the Battery Charger ......................................................3
3.0 Charging Proles ....................................................................................4
4.0 Identifying Charger Serial Number ........................................................5
Table 1 Charger Error & Fault Codes ............................................................ 6
2Curtis Models 1622, 1626, and 1627 Manual
SAFE OPERATING INSTRUCTIONS
• The charger has up to 25 selectable charging proles stored in its internal memory to charge
batteries. These proles are specic to each manufacturer and model of battery. Your equipment
supplier or charger distributor is responsible for ensuring the active charge prole matches the
battery pack charging requirements. Contact them with any questions about which prole to
select for each battery pack.
• The charger may become hot during charging. Use hand protection to safely handle the charger
during charging.
• To maintain safe operations, the unit automatically reduces its output power if the temperature
rises above set thresholds or if the AC input voltage is too low. The charger also reduces output
power if it detects the battery pack is damaged.
• If power is interrupted, and then returns, the charger starts and continues to operate without
hazard to the user, or damage to the batteries.
• Unplug the charger from both AC and DC sources when cleaning, moving or conducting any
maintenance or repair on the charger. No user- serviceable parts are inside. Do not remove the
cover due to the risk of electrical shock.
• Do not expose the charger to oil, dirt, mud or direct heavy water spray when cleaning the vehicle
or machine.
• If the detachable AC input power cord set or DC output cord is damaged, do not use the charger
until they are replaced with cord sets appropriate to your region and application.
• When mated with a sealed AC cord, the charger meets IP66 specications, making it dust-tight
and protected against powerful water jets. If a cord set with an unsealed connector is used, the
plug and connector must be periodically inspected to ensure the contacts are clean and dry.
- If this charger is provided with an AC cord set and the power plug does not match the power
outlet, contact the equipment manufacturer, distributor, or Curtis Instruments for the correct
AC cord set terminating with a 3-prong plug suitable for your region’s grounded power outlet.
- In North America (and other 120V AC regions), the AC cord must be a 3-conductor UL Listed/
CSA approved detachable cord set at least 1.8m in length (≥ 6 feet), minimum 16AWG and
rated SJT; terminated with 250V, 13A or greater connector.
- In Japan, the AC cord must be a 3-conductor PSE approved detachable AC cord set
terminated with 100V, 15A or greater connector.
- In 220-240 VAC regions, the AC cord must be a 3-conductor safety approved cord set, with
1.5mm² conductors(min.), rated appropriately for industrial use. The cord must be terminated
on one end with a grounding
type input plug appropriate
for use in the country of
destination and both plug and
connector should be rated
250V, 10A, or greater.
• Extension cords must be 3-wire
cord no longer than 30m (100’) at
10 AWG or 7.5m (25’) at 16 AWG,
per UL guidelines.
Only use compatible IEC320 C13 cables, as shown above
Product specificaties
| Merk: | Curtis |
| Categorie: | Batterij-oplader |
| Model: | 1627 |
Heb je hulp nodig?
Als je hulp nodig hebt met Curtis 1627 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Batterij-oplader Curtis
18 Juni 2025
17 Juni 2025
Handleiding Batterij-oplader
- Cellular Line
- Kemo
- Black Decker
- Shure
- Conceptronic
- Milwaukee
- Panduit
- EA Elektro Automatik
- ProUser
- Vivanco
- Toshiba
- Xtorm
- Bluetti
- Valcom
- Thomson
Nieuwste handleidingen voor Batterij-oplader
15 Juni 2025
15 Juni 2025
12 Juni 2025
12 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
6 Juni 2025