CTA Digital PAD-CGSWAO Handleiding

Bekijk gratis de handleiding van CTA Digital PAD-CGSWAO (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.4 sterren uit 7 reviews. Heb je een vraag over CTA Digital PAD-CGSWAO of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PAD-CGSWAO

INSTRUCTION - MANUAL

Contents :

2. Assembling the base stand3. Locking casters :

1. Assembling the wheels :

INSTRUCTIONS :

4. Setting up Foam Piece on Holder

5. Inserting a Tablet into Holder

A

F

6. Assembling base stand with gooseneck,

holder and battery cradle :

7. Setting up handle :

8. Setting up basket :

A

B

B

M

M

Y-Screw

How to flex and adjust product :

Portrait & landscape

Adjusting Gooseneck

Asjusting height

888-733-4448

for 7-13-Inch Tablets

888-733-4448

Compact Gooseneck Floor

Stand with Accessories (White)

x1

B

B

C

C

x2

x1

V

Allen Key

5x30x80mm

x4

Spring Washer

M8 mm

G

Cap Nuts

M8 mm

x4

F

L

x1x1

Foam

Bundle

Battery

Cradle

A

x1

x4

E

x1

K

Wrench

Tool

H

Nuts

M5 mm

x4

Washer

M6x12x1mm

I

x8

Screw

M5x25mm

J

x4

x1

D

N

x1

P

x1

R

x1

O

x2

Q

x1

S

x2

T

x2

U

x2

G

E

1A. Place spring washer (G) over the screw

bolt on the wheel (E).

1B. Place the screw of the wheel (D) through the metal

base.(C). Place nut cover (F) over the top. Turn in screw nut

(F) to wheel using hand.

1C. Follow up by using provided wrench tool (K) to

securely tighten as seen above.

F

C

E

E

G

3A. Press the wheel lever up or down to place

wheels in locked or unlocked mode depending

if you want to be in a mobile or stationary setup.

Make sure you adjust all (4) wheels at the same

time or it won’t properly be setup.

2A. Place the metal base pieces (C) in a

cross position and align the holes on the

base pole (B). One of the metal pieces

will be slighty higher at the middle, so

that piece will be on top.

V

J

I

I

H

2B. Insert the screw bolt (K) through all of them in

the corresponding order as shown. Using your

hand to initially rotate in the screw while your other

hand is holding the hex nut (I). Afterwards, use the

provided allen key tool to securely tighten. Repeat

for all (4) holes in the same manner.

6A. Take the gooseneck with holder (A), the battery cradle

(M), the base stand (B), and align them all together as shown

in the right. First, hook the battery cradle onto the base stand

metal adapter. Then rotate in the gooseneck component (A)

into the base stand (B) until securely tightened. Turn the Y

screw (see detail diagram to the right) to securely fasten the

gooseneck to the base stand.

4A. Peel off backing on the desired foam piece (L) to be

adhesed onto holder (A). Foam piece is to aid in having your

tablet be securely fitted onto the holder for a sturdy grip. Use

any combination of foam pieces as needed if 1 foam piece

isn’t enough.

5A. Press the release button on the side of the holder (A). While holding the button,

extend the arms so you’re able to insert your device. Press the button again to retract

arms and firmly grip at the corners of your device securely.

**Tablet Not Included. For

Illustration Purposes Only

7A. Find the desired height on

the pole / floorstand (B) where

you wish to attach the handle

(N). Then align the screw and

the U bracket (O,P) with the

opening in the handle (N).

8A. Find the desired height on the pole / floorstand (B) Align

U bracket (R) holes with basket screw holes on either side

of the central pole. Pass screw (U) through washer (T), then

through screw hole, and turn in nut (S) on opposite side.

7B. Rotate in screw clock

wise as shown until

securely tightened.

Identify the center pole height adjustment knob.

Rotate clockwise and counterclockwise to raise

or lower the center pole for preferred height.

Once desired height is set, rotate knob in the

middle opposite side of the handle to tighten

and create a more rigid and secure setup.

Using your hands, simply adjust

for a multitude of angles the

gooseneck until desired orienta-

tion, tilt angle, side angles are all

achieve for the preferred setup.

Using an allen key, tighten the

joint to create a more static

and rigid setup. Loosen to

allow adjustabil-ity as needed.

Rotate the joint behind the tablet

holder in a 360 degree fashion as

shown to either portrait or landscape

orientation as preferred.

**Tablet Not Included. For Illustration

Purposes Only.

M

A

P

N

O

Tightening &

loosening main joint

S

T

U

R

Product specificaties