Chamberlain 041D8214 Handleiding

Bekijk gratis de handleiding van Chamberlain 041D8214 (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 71 mensen en kreeg gemiddeld 4.4 sterren uit 9 reviews. Heb je een vraag over Chamberlain 041D8214 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

End Panel Replacement

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing

ANY service or maintenance.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing

the battery or working around the battery compartment.

A

B

D

C

E

F

WAR NIN G t

AVERTISSEMENT

WARNING: To av oid SERIOUS

PERSONAL INJURY or DEATH

from electrocution, disconnect

ALL electric a nd ba ttery power

BEFORE performing ANY

maintenance.

AVERTISSEMENT: Pour éviter

des BLESSURES GRAVES ou la

MORT pa r électrocution,

débrancher l’a limenta tion

électrique et de batterie AVANT

TOUTE intervention de

maintenance.

PA

RT

NUMBER:

S ERIAL NUM BER

DATE:

132B2759-5

MAC ADDRESS

IC: 2666A -

FCC ID:

To conne ct to a Wi-Fi Network, visit

wifihelp.cham berlain.c om for more

details . You will nee d your "MyQ Serial

Number " to complete s e tup.

100W Max26W

Max

THE CHAMBERLAIN GROUP INC.

ELMHURST IL, 60126, USA

Ass embled in Mexico

CONTAINS:

FCC ID: COFWMNBM11

IC: 10239A-WMNBM11

Pour vous conne cter à un ré s e au Wi-Fi,

visite z wifihelp.c hambe rlain.com pour

plusde dé tails. Vous aure z be s oin de votre

« Numéro de Série MyQ » pour

complé ter l’installation.

NETWORK SETUP CODE

Red

White

White

Grey

Receiver

Logic

Board

Receiver

Logic

Board

End

Panel

Antenna

wires

End

Panel

Wire

Harnesses

Light Socket Wires

To insert or remove

the wires from the

terminal, push in

the tab with a

screwdriver tip.

Installation

NOTE: The products illustrated in the instructions are for reference. Your

product may look different.

1. Disconnect electrical and battery power (if applicable) to the garage

door opener.

2. Remove the light lens.

• To remove the lens press the release tabs on both sides of lens.

Gently rotate lens back and downward until the lens hinge is in the

fully open position. Lift lens up slightly and remove.

OR

• Press the release tabs on both side of the lens. Squeeze the light

lens clips to remove lens from end panel.

OR

• Remove the light lens by pulling the top sides of the light lens and

rotate the light lens down. Squeeze the light lens clips to remove

lens from end panel.

3. Disconnect the wires (). A

4. Remove the end panel.

• Unplug the wire harnesses from the receiver logic board (). B

• Remove the receiver logic board ().C

• Remove antenna wires from holes in the old end panel ().D

• Unplug the wires for the light socket ().E

5. A blank label has been provided with your replacement end panel.

Copy the MyQ® Serial Number and all other information from the

original end panel label to the new label. This information is needed

when connecting your garage door opener to the Internet. Apply new

label to replacement end panel ().F

6. Discard old end panel.

7. Install the new end panel.

• Connect the wire harnesses to the receiver logic board ().B

• Reinstall the receiver logic board ().C

• Insert the antenna wires through the holes in the end panel ().D

• Connect the wires to the light socket (E ).

• Attach the end panel.

8. Reinsert the wires (). A

Door control wires: • white wire into the white terminal.

• white/red wire into the red terminal.

Safety sensor wires: • white wires into the white terminal.

• white/black wires into the grey terminal.

9. Attach the light lens. Make sure the antenna wires are hanging

straight down.

10. Reconnect power to the garage door opener.

11. Test of the safety reverse system. Refer to the owner’s manual.

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer

or birth defects or other reproductive harm. For more information

go to www.P65Warnings.ca.gov

Product specificaties