Axxess AX-MAZCAM Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Axxess AX-MAZCAM (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
axxessinterfaces.com • metraonline.com axxessinterfaces.com • metraonline.com
Axxess Integrate Axxess Integrate
Installation Instructions for AX-MAZCAM
REV. 1/25/16 REV. 1/25/16
Installation Instructions for AX-MAZCAM
FEATURES
• Retains the factory back-up camera to an aftermarket radio
Allows an aftermarket camera to be added to the factory screen
INTERFACE COMPONENTS
AX-MAZCAM harness
AX-MAZCAM
Mazda Back-Up Camera Retain/Add-On
2007-2015
MAZDA
CX-5 2013-2015
CX-7 2007-2012
CX-9 2007-2015
Mazda6 2011-2015
• Cutting tool • Tape • Crimping tool
• Connectors (example: butt connectors, bell caps, etc.)
APPLICATIONS
TOOLS REQUIRED
K PNOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most cognized and spected re re
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for mo information and take steps re
toward a bet ter tomorrow.
Metra recommends MECP
certified technicians
Connections to be made
The AX-MAZCAM can be connected two different ways
To retain the factory back-up camera to an aftermarket radio:
Connect the wire to chassis ground.Black
Connect the Yellow wire to accessory power.
Connect the male Yellow RCA jack to the rear camera input of the aftermarket radio.
Connect the reverse wire from the aftermarket radio, to the reverse signal in the vehicle.
To allow an aftermarket camera to be added to the OEM screen:
Connect the wire to the ground wire of the aftermarket camera.Black
Connect the Yellow wire to battery wire of the aftermarket camera.
Connect the female Yellow RCA jack to the aftermarket camera.
CAUTION!
Metra recommends disconnecting the negative battery terminal before beginning any instal
-
lation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership
for more information. All accessories, switches, climate controls panels, and especially air bag indicator
lights must be connected before reconnecting the battery or cycling the ignition. Also, do not remove the
factory radio with the key in the on position, or the vehicle running. It would be best to remove the key
from the ignition and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
axxessinterfaces.com • metraonline.com axxessinterfaces.com • metraonline.com
Axxess Integrate Axxess Integrate
REV. 1/25/16 REV. 1/25/16
Instrucciones de instalación para AX-MAZCAM Instrucciones de instalación para AX-MAZCAM
Conexiones que se deben hacer
El AX-MAZCAM puede conectarse de dos maneras distintas
Para retener la cámara de reversa de fábrica para un radio de mercado secundario:
Conecte el cable a la tierra del chasís.negro
Conecte el cable a la alimentación de accesorios.amarillo
Conecte el conector RCA RCA en la entrada de la cámaramacho amarillo
de reversa del radio de mercado secundario.
Conecte el cable de marcha atrás del radio de mercado secundario, a la señal
de marcha atrás en el vehículo.
Para permitir que seada una cámara de mercado secundario
a la pantalla de equipo original:
Conecte el cable al cable de tierra de la mara de mercado secundario.negro
Conecte el cable al cable de la batería de la cámara de mercado secundario.amarillo
Conecte el conector RCA hembra
amarillo
a la cámara de mercado secundario.
CARACTERÍSTICAS
• Retiene lamara de reversa de fábrica para un radio de mercado secundario
• Permite que se añada una cámara de mercado secundario a la pantalla de fábrica
COMPONENTES DE LA INTERFASE
Arnés AX-MAZCAM
AX-MAZCAM
Retener/adir cámara de reversa de Mazda
2007-2015
MAZDA
CX-5 2013-2015
CX-7 2007-2012
CX-9 2007-2015
Mazda6 2011-2015
• Herramienta de corte • Cinta • Ponchadora
• Conectores (ejemplo: conectores de extremo, de campana, etc.)
APLICACIONES
HERRAMIENTAS REQUERIDAS
Metra recomienda técnicos
con certificacn del Programa
de Certificación en Electrónica
Móvil (Mobile Electronics
Certification Program, MECP).
EL CONOCIMIENTO ES PODER
Mejore sus habilidades de instalación y
fabricación inscribiéndose en la escuela de
disposit ivos electrónicos móviles más reconocida
y respetada de nuestra industria. Regístrese en
www.inst allerinst it ute.com o llame al
800-354-6782 para obtener más información y
avance hacia un futuro mejor.
¡PRECAUCIÓN!
Meta recomienda desconectar la terminal negativa de la batería antes de iniciar
cualquier instalación, a menos que el fabricante del vehículo recomiende lo contrario. Verifique con su
concesionario local si existe más información. Todos los accesorios, interruptores, paneles de controles
de clima y especialmente las luces del indicador de las bolsas de aire deben estar conectados antes de
reconectar la batería o ciclar la ignición. Además, no quite el radio de fábrica con la llave en la posición
de encendido ni con el vehículo funcionando. Sería mejor retirar la llave de la ignición y esperar unos
cuantos segundos antes de quitar el radio de fábrica.


Product specificaties

Merk: Axxess
Categorie: Niet gecategoriseerd
Model: AX-MAZCAM

Heb je hulp nodig?

Als je hulp nodig hebt met Axxess AX-MAZCAM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Axxess

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd