ZZ-2 ZW-GM Handleiding
ZZ-2
Niet gecategoriseerd
ZW-GM
Bekijk gratis de handleiding van ZZ-2 ZW-GM (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 4 mensen en kreeg gemiddeld 4.7 sterren uit 2.5 reviews. Heb je een vraag over ZZ-2 ZW-GM of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
P
P
P
PPlug
lug
lug
lug lug & Play
& Play
& Play
& Play& Play, BC
, BC
, BC
, BC, BCM-Con
M-Con
M-Con
M-ConM-Control
trol
trol
troltrolled,
led,
led,
led, led, OE L
OE L
OE L
OE LOE Light F
ight F
ight F
ight Fight Flash
lash
lash
lash lash Mo
Mo
Mo
MoModule
dule
dule
duledule
Z-WAGZ unit, the simplest BCM-module fo
pre-programmed with 8 different light patterns, some for halogen systems & s
including -board LED status. on
Operation for all GM vehicles is the same:
1. Install the Z-WAGZ unit to the OE BCM unit. Follow instructions on page 2 for all vehicles.
2. Turn Ignition ON (Ignition must be on for proper operation). Leave vehicle in Park.
3. To activate Z-WAGZ:
o Press and HOLD the lever (5 sec) high beam OR
o Press and HOLD the provided push button (3 sec) OR
o Send a latched 12v (+) signal to the (designed to be extended for OE -fitter switches) blue wire up
Pattern 1 will begin to flash. Once pattern 1 begins, the hazards in the gauge cluster will blink 1 time, indicating Pattern 1
has been selected and the LED on the unit will blink . BLUE See chart for remaining pattern color indication.
4. To switch to Pattern 2: (Pattern 1 must be currently active)
o Engage either turn signal, then press and HOLD the lever once more (5 sec)high beam . OR
o Press & release the provided push button
The hazards will blink twice indicating Pattern 2 has been selected. Repeat this process to switch to the n
5. To deactivate Z-WAGZ:
o Press and HOLD the lever high beam OR
o Press and HOLD the provided push button OR
o Release (+) signal to the (if connected this way) 12v blue wire
NOTES:
• Vehicles equipped with LED lights should use LED patterns. Vehicles equipped with standard bulbs should use bulb patterns.
• Not all lights on the vehicle are necessarily used, some lights are not controllable via BCM CAN data.
• Z-WAGZ will retain the last used pattern, even after being disconnected from the BCM (if ever) .
• When flashing is active: turn signals, headlights & reverse lights will override pattern flashing, until turned off again .
• When on some patterns, in some vehicles, the reverse camera image may show up/flash on the OE screen (if equipped). This
is a factory limitation and is normal. If you want to avoid this, keep DIP (3) OFF .
• ‘Plow Mode’, when active (INPUT 2), disables High & Low beam flashing and slows the pattern down so that the relay box
(plow module) can keep up with the flashing (prevents overheating).
I/O Button Harness
(optional use)
ZW-GM
T-Harness
MODEL
LOCATION
Silverado/Sierra/Colorado
Underneath steering
wheel / dash area
MAKE
MODEL
YEAR
GM
Silverado / Sierra
2014- 2022.5
Colorado / Canyon
2018-2022.5
Silverado
Sierra 2500/3500 HD
2014-2022.5
Tahoe/Suburban
2018-2020
G
G
G
GGM V
M V
M V
M VM Veh
eh
eh
ehehicle Ins
icle Ins
icle Ins
icle Insicle Insta
ta
ta
tatallatio
llatio
llatio
llatiollation
n
n
n n
1. Locate the BCM unit. The chart below indicates the
BCM location in various vehicles.
2. With the vehicle OFF: disconnect the (4) highlighted
plugs shown. Connect the male side of each T-
Harness to the BCM and the (removed) plugs into the
female side of the Z-WAGZ BCM harnessing. These
connectors can only fit in one place and connect in
one way and are color matched to the OE plugs.
3. Connect the Z-WAGZ BCM unit to the 22-pin
connector, tie-wrap the unit to another harness if
desired .
4. Return to page (1) for operation instructions.
OE Body Control Module GM
C
C
C
CConf
onf
onf
onfonfirme
irme
irme
irmeirmed V
d V
d V
d Vd Vehicles
ehicles
ehicles
ehiclesehicles:
:
:
: :
GM
GM
GM
GMGM BCM
BCM
BCM
BCM BCM Locat
Locat
Locat
LocatLocations
ions
ions
ionsions:
:
:
: :
*‘Plow Mode’, when active (INPUT 2), disables High & Low beam
flashing and slows the pattern down so that the relay box (plow
module) can keep up with the flashing (prevents overheating).
This should be enabled whenever a plow is connected.
3 | P a g e
555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212
3
4
5
6
ON
Disable
High
Beam
Disable
Low
Beam
Enable Reverse Light
(May cause reverse camera to
show on screen while active)
For HALOGEN
equipped
(slower)
Disable STROBE Mode
(Removes strobe every
3 seconds)
N/A
OFF
Enable
High
Beam
Enable
Low
Beam
Disable Reverse Light
For LED
equipped
(faster)
Enable
STROBE Mode
N/A
Located on the back side of the
unit is a bank of (6) dip switches
– you will need a pick-tool to
adjust.
‘Plow Mode’, when active (INPUT 2), disables High & Low beam flashing and slows the pattern down so that the relay box (plow
module) can keep up with the flashing (prevents overheating). This should be enabled whenever a plow is connected.
DIP S
DIP S
DIP S
DIP SDIP Switch S
witch S
witch S
witch Switch Set
et
et
etettings
tings
tings
tingstings, Ex
, Ex
, Ex
, Ex, Extra Fea
tra Fea
tra Fea
tra Featra Featur
tur
tur
turtures
es
es
eses
All dip switches are LIVE, do not unplug the module to adjust.
22-Pin (power/data connections)
DIP Switches (options)
USB (updates)
12-PIN push button
I/O harness
LED Status
Product specificaties
| Merk: | ZZ-2 |
| Categorie: | Niet gecategoriseerd |
| Model: | ZW-GM |
Heb je hulp nodig?
Als je hulp nodig hebt met ZZ-2 ZW-GM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd ZZ-2
24 Mei 2025
24 Mei 2025
24 Mei 2025
30 Januari 2025
Handleiding Niet gecategoriseerd
- Izzy
- Sinus Live
- Valueline
- Inkbird
- Akuvox
- Sennheiser
- BT
- Crane Song
- Lowrance
- Barazza
- Efbe-schott
- Lego
- Maxell
- Childhome
- Acopa
Nieuwste handleidingen voor Niet gecategoriseerd
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025