ZZ-2 ZW-FSD Handleiding
ZZ-2
Niet gecategoriseerd
ZW-FSD
Bekijk gratis de handleiding van ZZ-2 ZW-FSD (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.2 sterren uit 3 reviews. Heb je een vraag over ZZ-2 ZW-FSD of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
Plug & Play, OE Light-Controller for F’24 ORD F150 & ‘23+ Su
Thank you for purchasing a genuine Z-WAGZ unit, the simplest Plug & Play module
comes pre-programmed with 3 different light patterns and ha
ZW-FSD Operation:
1. Install the Z-WAGZ unit to the factory Body Control Module (BCM). Follow instructions on page
2 for more details and important information with this process.
2. Turn Ignition ON or start vehicle (Ignition must be ON or vehicle running for proper operation)
3. To activate Z-WAGZ:
o Press and HOLD the high beam lever (5 sec) OR
o Press and HOLD the provided push button (3 sec) OR
o Send a (+) signal to the 12v blue wire (designed to be extended for OE up-fitter
switches or any aftermarket toggle). For this input method, as long as the wire has 12v
(+), the Z-WAGZ unit will stay active.
Pattern 1 will begin to flash. Once pattern 1 begins, the cluster turn signal (indicators) will blink 1 time,
indicating Pattern 1 has been selected. The LED on the unit will blink BLUE. See chart on page 4 for
remaining pattern color indication.
4. To switch to Pattern 2: (Pattern 1 must be currently active)
o Engage either turn signal, then press and HOLD the high beam lever once more (5
sec) . OR
o Press & release the provided push button one time
T cluster turn signal (indicators) will blink twice indicating Pattern 2 has been selected. he Repeat this
process to switch to the next pattern.
5. To deactivate Z-WAGZ:
o Press and HOLD the high beam lever (5 sec) OR
o Press and HOLD the provided push button (3 sec) OR
o Release (+) signal to the 12v blue wire (if connected this way) OR
o Turn vehicle OFF
GENERAL NOTES:
• Vehicles equipped with LED lights should use LED patterns. Vehicles equipped with standard bulbs should use bulb patterns
but may get away with LED patterns (although some consistency may be lost).
• Not all lights on the vehicle are necessarily used, some lights are not controllable via CAN data commands.
• Z-WAGZ will retain the last used pattern, even after being disconnected from the harness (if ever).
• Turn signals, headlights & reverse lights will override pattern flashing when used, until turned off again.
• Lights on the external mirrors will only flash if wired with turn signals from factory .
• ‘Plow Mode’, when active (INPUT 2), disables High & Low beam flashing and slows the pattern down so that the relay box
(plow module) can keep up with the flashing (prevents overheating).
Activation Switch
and I/O Harness
ZW-FSD BCM
T-Harness
2 | P a g e
555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212
OE Ford BCM
1. On the passenger side of the truck,
remove the weather stripping near the
kick panel.
2. Remove the BCM access cover.
3. Release (4) clips and remove the right-
hand side lower cowl trim panel to expose
the BCM.
ZW
ZW
ZW
ZWZW-FSD Vehicle m
-FSD Vehicle m
-FSD Vehicle m
-FSD Vehicle m-FSD Vehicle modul
odul
odul
odulodule insta
e insta
e insta
e instae installation
llation
llation
llation llation
4. With the vehicle OFF: disconnect the (1)
circled plug shown. Connect the male side
of the provided T-Harness to the BCM and
the removed, OE plug into the female side
of the Z-WAGZ BCM harness. Th connector is
can only fit in one place and connect in one
way. Make sure the cam-lock is closed all
the way and the connector is seated fully.
5. Connect the provided ground to the factory
Ford ground location (indicated by the red
arrow).
6. Connect the ZW- unit to the 22-pin FSD
connector, tie-wrap the unit to another
harness if desired.
7. Return to page (1) for operation
instructions.
J2
3 | P a g e
555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212
MAKE
MODEL
YEAR
Ford
F150
2024
F250, F350, F450
2023+
Co
Co
Co
CoCompa
mpa
mpa
mpampatibl
tibl
tibl
tibltible Vehicles
e Vehicles
e Vehicles
e Vehiclese Vehicles:
:
:
: :
Product specificaties
| Merk: | ZZ-2 |
| Categorie: | Niet gecategoriseerd |
| Model: | ZW-FSD |
Heb je hulp nodig?
Als je hulp nodig hebt met ZZ-2 ZW-FSD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd ZZ-2
24 Mei 2025
24 Mei 2025
24 Mei 2025
30 Januari 2025
Handleiding Niet gecategoriseerd
- Lunsom
- JAR Systems
- PreSonus
- Elinchrom
- Shure
- Casa Deco
- Kanto
- Multimetrix
- Bezzera
- Nokia
- Ciclo
- Vonyx
- On-Q
- Vornado
- Getac
Nieuwste handleidingen voor Niet gecategoriseerd
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025