Zircon StudSensor AG717 Handleiding

Bekijk gratis de handleiding van Zircon StudSensor AG717 (2 pagina’s), behorend tot de categorie Meetapparatuur. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.6 sterren uit 8 reviews. Heb je een vraag over Zircon StudSensor AG717 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

EN

INSTALL 9-VOLT BATTERY

Always use a new alkaline

battery with an extended

expiration date. Match battery

direction to image inside of

battery cavity.

WARNING

Do not rely exclusively on the

tool to locate items behind

a surface. Use other information to help

locate items before penetrating the surface,

including construction plans, visible points

of entry of pipes and wiring into walls

such as in a basement, and standard

stud-spacing practices.

POWER UP

To activate tool, press and hold Power Button.

If button is not held, unit shuts off.

FIND A STUD

The tool is designed to locate the edges of wood

and metal studs up to

3

⁄4" (19 mm) behind the

scanned surface.

The accuracy of the position of a stud found is

typically within

1

⁄8" (3 mm).

For best results,

hold the tool as shown

(Figure A), and move

slowly when scanning.

Do not touch the

surface during

calibration or scan.

WORKING WITH

DIFFERENT MATERIALS

Wallpaper This tool functions normally on walls

covered with wallpaper or fabric, unless the materials

are metallic foil, contain metallic fibers, or are still

wet after application. Wallpaper may need to dry for

several weeks after application.

Freshly painted walls Paint may take a week or

longer to dry after application.

Lath and plaster Due to irregularities in plaster

thickness, this tool is not recommended for use on

lath and plaster.

Highly textured walls or acoustic ceilings

When scanning a ceiling or wall with an

uneven surface, place thin cardboard on the

surface to be scanned.

This tool cannot scan for wood studs and joists

through carpet and padding.

Electrical wiring and pipesDepending on

the proximity of electrical wiring or pipes to the

wall surface, the tool may detect them in the same

manner as studs.

Caution should always be used when nailing,

cutting, or drilling in walls, floors, and ceilings

that may contain these items.

1. Hold tool flat against wall, then press and

hold Power Button. In 1 – 2 seconds, the unit will

calibrate, and the Green READY Light will illuminate.

DO NOT MOVE TOOL DURING CALIBRATION.

2. While holding down the Power Button, slide the

tool slowly along the wall.

3. When the tool

reaches the edge of

the stud, the Red EDGE

Light will illuminate, the

SpotLite

®

Pointer will shine,

and a steady tone

will sound. Mark the spot.

()Figure B

4. Without releasing

Power Button, continue the

scan direction until the

Red EDGE Light and the

SpotLite

®

Pointer turn off,

then reverse direction.

5. Slide the tool until the

other edge of the stud is

detected and mark this

as well. (Figure C)

The center of the stud is the midpoint

between the two marks.

OVER-THE-STUD WARNING

If scanning begins directly over a stud, the tool will

emit a continual beep. If this happens, restart the

scan in a different location.

WIREWARNING

®

DETECTION

WireWarning

®

Detection works

continuously during a scan.

When live, unshielded AC

voltage is detected,

the WireWarning

®

Detection

Indicator lights up. If scanning

begins over a live AC wire,

the WireWarning

®

Detection

Indicator will flash continuously. (Figure D)

Use extreme caution under these circumstances,

and whenever live AC wiring is suspected.

WARNING

THE TOOL MAY NOT DETECT

LIVE CURRENT IF WIRES ARE

MORE THAN2" (50 mm) BELOW THE SCANNED

SURFACE, INCONCRETE, ENCASED IN CONDUIT,

BEHIND APLYWOOD SHEAR WALL OR METALLIC

WALLCOVERING, OR IF MOISTURE IS PRESENT

IN THE ENVIRONMENT OR SCANNED SURFACE.

WARNING

DO NOT ASSUME THERE ARE

NO LIVE ELECTR ICAL WIRES IN

THE WALL. DO NOT TAKE ACTIONS THAT COULD

BE DANGEROUS IF THE WALL CONTAINS A LIVE

ELECTRICAL WIRE. ALWAYS TURN OFF THE

ELECTRICAL, GAS, AND WATER SUPPLIES

BEFORE PENETRATING A SURFACE. FAILURE TO

FOLLOW THESE INSTRUCTIONS MAY RESULT IN

ELECTRIC SHOCK, FIRE, AND/OR SERIOUS

INJURY OR PROPERTY DAMAGE.

Studs and joists are normally spaced 16 or 24"

apart (40 or 60 cm), and are 1

1

⁄2" (38 mm) wide.

Anything closer together, or of a different width,

may not be a stud or joist.

NOTE: Sensing depth and accuracy can

vary depending on scanning environment

conditions such as mineral content, moisture,

texture and consistency of the wall materials.

This tool is designed for use with:not

• Ceramic floor tile

• Carpeting and padding

• Wallpaper with metallic fibers

• Freshly painted walls that are still damp (may take

one week or longer to dry after application)

• Lath and plaster walls

• Foil-covered insulation board

• Glass or any other dense material

• Surfaces thicker than

3

⁄4" (19 mm)

BEFORE YOU BEGIN

ZIRCON

®

STUD FINDERS WORK BY SENSING DENSITY CHANGES BEHIND THE WALL. OTHER OBJECTS CAN

BE DETECTED ESPECIALLY IF THEY ARE VERY CLOSE TO THE WALL. DO NOT ASSUME EVERYTHING

DETECTED IS A STUD.

- Always use a new alkaline battery with an extended expiration date. Match battery direction to image inside

of battery cavity.

- Do not rely exclusively on the tool to locate items behind a surface. Use other information to help locate such

items before penetrating the surface, including construction plans, visible points of entry of pipes and wiring

into walls such as in a basement, and standard stud-spacing practices.

- Always scan for studs at several different heights on the wall and mark the location of every target indicated

by the stud finder. This is called “mapping the wall.” Pipes and other objects will likely not give consistent

readings from floor to ceiling, like a stud will.

- Readings should always be consistent and repeatable.

- Zircon

®

stud finders are recommended for interior use only.

- Studs normally run from floor to ceiling, except above and below windows, and above doors.

- Other objects commonly contained in walls, floors, or ceilings are water pipes, gas lines, firestops,

and electrical wiring.

- Sensing depth and accuracy can vary depending on scanning environment conditions such as mineral

content, moisture, texture and consistency of the wall materials.

- Always turn off power when working near electrical wires.

- Depending on the proximity of electrical wiring or pipes to the wall surface, the tool may detect them in the

same manner as studs. Caution should always be used when nailing, cutting, or drilling in walls,

floors, and ceilings that may contain these items.

- Studs and joists are normally spaced 16 or 24" (40 or 60 cm) apart, are normally 1

1

⁄2" (38 mm) wide,

and may be separated by firestops. Anything closer together, or of a different width, may not be a stud or joist.

StudSensor

™

HD

35

Edge-Finding Stud Finder

TROUBLESHOOTING & CONSTRUCTION TIPS

SITUATIONLIKELY CAUSESOLUTION

No indications.No studs in the area.Move tool several inches (13 – 15 cm) to the left or right and start again.

READY Icon shows

but nothing happens

when scanning.

Tool may not be flat

against wall.

Hold tool so that the pads on the back make full contact with the surface.

Unit beeps repeatedly.

Tool was calibrated over a stud

or on dense part of wall.

Turn tool off, move over a few inches (5 – 8 cm), press Power Button,

and start again.

Tool tilted or lifted during scan.

On rough surfaces, place thin cardboard on wall, scanning over it to help

slide tool more smoothly.

Tool detects objects

other than studs tor

finds more studs than

should be there.

Electrical wiring and metal or

plastic pipes may be near to

or touching the back of the

wall surface.

• Check for other studs equally spaced to either side at 12, 16 or 24"

(30, 40, or 60 cm), or check for the same stud at spots directly above or

below the first scan area. Studs will run straight up and down, from floor

to ceiling, while pipes may change direction. Standard studs measure

approximately 1

1

⁄2" (38 mm) between edges. Anything larger or smaller is

likely not a stud (unless near door or window).

• Use caution when nailing, sawing or drilling into walls, floors and ceilings

where these items may exist.

Electrical wires

suspected but

WireWarning

®

Detection

does not alert.

• Wires are shielded by a

metal conduit, braided wire,

or metallic wall covering.

• Wires deeper than 2"

(50 mm) from the surface

might not be detected.

• Wires may not be live.

• If there is an outlet switch, turn it to ON position while scanning, but turn

OFF when working near the wires. Use extra caution if the area has

plywood, thick wood backing behind drywall, or walls that are

thicker than normal.

• See above.

• Plug a lamp into the outlet and turn it on to test whether wires are live.

Visit www.zircon.com for the

most current instructions.

FCC Part 15 Class B Registration Warning:

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

LIMITED LIFETIME WARRANTY

Zircon Corporation (“Zircon”) warrants to the

original purchaser (or original user by gift)

that this product will be free from defects in

materials and workmanship for its useful life

(not to exceed twenty years from date

of purchase). This warranty is limited to

the electronic circuitry of the product, and

specifically excludes consumable parts,

including batteries, and software, even if

packaged with the product. Defects caused

by abuse, modification, handling contrary to

these instructions, other unreasonable use, or

neglect are not covered under this warranty.

No liability is accepted for normal wear and

tear and minor defects which do not detract

from the function of the product.

THIS LIMITED LIFETIME WARRANTY IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. IN NO EVENT WILL

ZIRCON BE LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM POSSESSION, USE, OR

MALFUNCTION OF THIS PRODUCT. NO OTHER

REPRESENTATIONS OR CLAIMS OF A SIMILAR

NATURE WILL BIND OR OBLIGATE ZIRCON.

Some states do not allow limitations on certain

implied warranties and/or the limitation on

incidental or consequential damages, so the

above limitations and exclusions may not apply

to you. This warranty gives you specific legal

rights, and you may also have other rights which

vary from state to state. This Limited Lifetime

Warranty applies only to products purchased

within the United States of America (USA)

and Canada. For warranty applicable to products

purchased in all other geographical areas,

see www.zircon.com/warranty.

Any in-warranty defective product returned

to Zircon, freight prepaid, along with dated

purchase receipt and $10.00 to cover shipping

and handling, will be repaired or replaced,

at Zircon’s option. If the returned product is

no longer available, Zircon may replace the

product with a similar product of similar

function. This is your sole and exclusive remedy

for breach of this Limited Lifetime Warranty.

To return product, call the Zircon Customer

Service number below to request an RMA

number and return product with shipment

tracking to:

Zircon Corporation

Attn: Returns Department

1580 Dell Avenue

Campbell, CA 95008-6992 USA

Include your name, return address, RMA number,

and package tracking number. Allow 4 to 6

weeks for delivery.

If you do not agree to the terms of this Limited

Lifetime Warranty, you may not use this product

and must promptly return it to the retailer, along

with a dated purchase receipt within 30 days of

purchase for a refund of the purchase price.

Customer Service: 1-800-245-9265

or 1-408-963-4550

Monday–Friday, 8:00 a.m.–5:00 p.m. PST

www.zircon.com • [email protected]

©2021 Zircon Corporation

P/N 72012 • Rev A 03/21

SpotLite, StudSensor, WireWarning, and Zircon

are trademarks or registered trademarks of

Zircon Corporation.

SpotLite

®

Pointer

Stud Edge Groove

Battery Door Tab

(door on bottom)

WireWarning

®

Detection Indicator

Ergonomic Grip

Power

Button

Red EDGE Light

Green READY

Light

Figure A

Figure C

Figure B

Figure D

Product specificaties