Yato YT-6745 Handleiding
Pagina's 16 Lijmpistool
Bekijk de handleiding van Yato YT-6745 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag

INSTRUKCJA OBSUGI
Ł
1
PISTOLET DO PIANKI MONTAOWEJ
Ż
FOAM GUN
PISTOLE FÜR MONTAGESCHAUMSTOFF
ПИСТОЛЕТДЛЯМОНТАЖНОЙПЕНЫ
ПІСТОЛЕТДЛЯМОНТАЖНОЇПІНИ
MONTAŽINI PUT PISTOLETAS
ŲŲ
MONTŽAS PUTAS PISTOLE
Ā
PISTOLE NA MONTÁŽNÍ P
Ě
NU
PIŠTO NA MONTÁŽNU PENU
Ľ
SZERELHAB-PISZTOLY
Ő
PISTOL PENTRU SPUMA DE MONTAJ
PISTOLA PARA LA ESPUMA DE INSTALACIÓN
PL
GB
D
RUS
UA
LT
LV
CZ
SK
H
RO
E
YT-6745
TOYA S.A. ul. Sołtysowicka 13-15, 51-168 Wrocław, Polska

INSTRUKCJA OBSUGI
Ł
2
PL
Przed przystąpieniem do eksploatacji niniejszego urządzenia przeczytaj całą instrukcję i zachowaj ją.
UWAGA! W celu zapewnienia prawidłowego działania pistoletu nie zaleca się demontować z pistoletu nie do końca zużytej butli z pianką. Zaleca się
całkowite zużycie pianki z raz zamontowanego pojemnika.
1. ZASTOSOWANIE
Pistolet do pianki montażowej jest przeznaczony do nakładania pianki jednoskładnikowej dostępnej w pojemnikach ciśnieniowych. Pistolet ułatwia
wykonywanie takich prac jak: uszczelnianie, montaż okien i drzwi, wypełnianie szczelin w izolacji, uszczelnianie i izolacja ścianek działowych oraz
ocieplanie ścian i dachów.
2. ZALECENIA BEZPIECZEŃSTWA
Szczegółowe instrukcje dotyczące bezpieczeństwa stosowania pianki montażowej są zawarte przez producentów na opakowaniach pianki i należy
się do nich bezwzględnie stosować.
Nigdy nie kierować wylotu pistoletu w kierunku ludzi - pianka i płyn czyszczący do pistoletu mogą być powodem uszkodzeń ciała i innych urazów.
Na stanowisku pracy powinna być zapewniona skuteczna wentylacja.
Pistolet należy używać z daleka od źródeł ciepła i ognia, ponieważ może to spowodować jego uszkodzenie lub pogorszenie funkcjonowania.
Przestrzegać ogólnych zasad bezpieczeństwa przy wykonywaniu prac montażowych i stosować odpowiednio dobrane środki ochrony osobistej
takie jak okulary, maski i rękawice.
Nigdy nie zostawiać zmontowanego układu bez nadzoru osoby uprawnionej do obsługi. Nie dopuszczać dzieci w pobliże zmontowanego układu.
Nigdy nie kierować strumienia pianki montażowej, lub środka czyszczącego na źródło ciepła bądź ognia, może to spowodować pożar.
3. INSTRUKCJA UŻYTKOWANIA
3.1. Rozpoczcie pracy
ę
Silnie wstrząsnąć pojemnikiem z pianką, przez około 15 sekund.
Wkręcić do oporu śrubę regulacyjną, znajdującą się z tyłu pistoletu tak, aby całkowicie zablokować ruch dźwigni spustowej.
Z pojemnika z pianką zdjąć pokrywkę, a następnie wkręcić pojemnik do nakrętki pistoletu do wyczuwalnego oporu. Następnie śrubę regulacyjną,
znajdującą się z tyłu pistoletu wykręcić obracając do momentu wyczucia oporu.
Nacisnąć dźwignię spustową i napełnić pistolet pianką.
Pistolet jest gotowy do użytku. Strumień pianki wypływa po naciśnięciu dźwigni spustowej.
Zwolnienie nacisku dźwigni spustowej powoduje zatrzymanie wypływu pianki.
Objętość strumienia pianki montażowej reguluje się poprzez obrót śruby regulacyjnej.
3.2. Czynnoci po zakoczeniu pracy
śń
Wkręcić do oporu śrubę regulacyjną tak, aby zablokować ruch dźwigni spustowej.
Zalecane jest nie wykręcanie pojemnika z pianką z pistoletu. Należy dbać, żeby do pistoletu zawsze był przykręcony, choć częściowo napełniony
pojemnik, pozwala to utrzymać piankę wewnątrz pistoletu pod ciśnieniem. Zapobiega to zasychaniu pianki wewnątrz pistoletu.
Jeśli przerwa w użytkowaniu pistoletu wynosi ponad miesiąc należy oczyścić pistolet za pomocą środka do czyszczenia pianki montażowej.
Nie wolno dopuszczać do zaschnięcia pianki wewnątrz pistoletu. Zaschniętą piankę można usunąć tylko mechanicznie.
Pozostawienie zaschniętej
pianki wewnątrz pistoletu, prowadzi do nieodwracalnej niedrożności pistoletu.
Nie może to być podstawą do roszczeń z tytułu gwarancji.
3.3. Ponowne uycie pistoletu
ż
Silnie wstrząsnąć pistoletem z zamocowanym pojemnikiem, przez około 15 sekund. Ostrym nożem odciąć końcówkę stwardniałej piany.
Odkręcić w lewo śrubę regulacyjną i wypuścić tyle piany, aby strumień stał się jednolity. Po tych czynnościach pistolet jest gotowy do użytku.
3.4. Wymiana pojemnika
Jeżeli z pojemnika przestała się wydostawać pianka należy zastąpić go nowym. Aby przekonać się czy pojemnik jest całkowicie drożny, należy
skierować dyszę w kierunku pojemnika na śmieci i naciskać dźwignię spustową, tak długo, aż dysza pistoletu będzie całkowicie drożna.
Zamontować natychmiast, nie oczyszczając pistoletu, nowy pojemnik i postępować zgodnie z punktem 3.1.
3.5. Czyszczenie pistoletu
Odkręcić pojemnik od pistoletu.
Na pojemnik ze środkiem czyszczącym założyć końcówkę rozpylającą i wyczyścić resztki świeżej piany, znajdujące się na pistolecie.
Zdjąć końcówkę rozpylającą i wkręcić w pistolet pojemnik ze środkiem czyszczącym. Postępować podobnie jak w przypadku pojemnika z pianką
(punkt 3.1.).
Napełnić pistolet środkiem czyszczącym i pozostawić na około 10 minut.
Ponownie nacisnąć dźwignie spustową i przeczyścić wnętrze pistoletu świeżym środkiem czyszczącym.
Odkręcić pojemnik ze środkiem czyszczącym. Za pomocą szmatki usunąć z miejsca połączenia pojemnika i pistoletu resztki środka
czyszczącego
i pokryć cienką warstwą wazeliny.
Nie należy czyścić pistoletu środkami powodującymi korozję.
Przy ciągłym użytkowaniu pistoletu należy czyścić pistolet, w wyżej opisany sposób, co 2 - 3 miesiące.

3
OPERATING INSTRUCTIONS
GB
Read and keep the entire instruction manual before the fi rst use of this device.
CAUTION! In order to ensure the proper functioning of the gun, it is not recommended to remove an unused foam cylinder from the gun. It is
recommended to use the foam completely once the container has been installed.
1. INTENDED USE
The assembly foam gun is designed to apply single-component foam available in pressure containers. The gun makes it easier to perform such tasks
as: sealing, installation of windows and doors, fi lling gaps in insulation, sealing and insulation of partition walls and insulation of walls and roofs.
2. SAFETY GUIDELINES
Detailed instructions for the safe use of the assembly foam are given by the manufacturers on the packaging and must be followed.
Never point the gun’s outlet at people - foam and cleaning fl uid in the gun may cause personal injury or other damage.
Eff ective ventilation should be provided at the workplace.
Use the gun away from heat sources and fi re as this may damage the device or impair its operation.
Observe the general safety conditions when carrying out assembly work and use the appropriate personal protective equipment such as glasses,
masks and gloves.
Never leave the assembled system without the supervision of a person authorised to its use. Do not let children near the assembled system.
Never direct the assembly foam stream or cleaning agent onto a heat or fi re source, as this may result in a fi re.
3. INSTRUCTIONS FOR USE
3.1. Starting work
Shake the foam container vigorously for approximately 15 seconds.
Screw in the adjusting screw on the back of the gun as far as possible to completely prevent the trigger lever from moving.
Remove the lid from the foam container and screw the container onto the gun nut until resistance is felt. Then unscrew the adjusting screw on the
back of the gun by turning it until resistance is felt.
Press the trigger lever and fi ll the gun with foam.
The gun is ready for use. The foam stream fl ows out when the trigger lever is pressed.
Releasing the trigger lever will stop the foam from fl owing out.
The volume of the foam stream is adjusted by turning the adjusting screw.
3.2. Activities after completing work
Screw in the adjusting screw to prevent the trigger lever from moving.
It is recommended not to remove the foam container from the gun. Make sure that at least a partially fi lled container is always screwed onto the gun
to keep the foam inside the gun under pressure. This prevents the foam from drying out inside the gun.
If the gun is not in use for more than a month, use an assembly foam cleaning agent to clean the gun.
Do not allow the foam to dry inside the gun. Dried foam may only be removed mechanically.
Leaving the dried foam inside the gun leads to an
irreversible blockage of the gun.
No warranty claims can be derived from this.
3.3. Reuse of the gun
Vigorously shake the gun with the container attached for approximately 15 seconds. Cut off the tip of the hardened foam with a sharp knife.
Unscrew the adjusting screw to the left and release enough foam to make the stream uniform. After this, the gun is ready for use.
3.4. Replacing the container
If foam no longer fl ows from the container, replace it with a new one. To see if the container is completely unobstructed, point the nozzle towards a
waste container and press the trigger until the pistol nozzle is completely unobstructed.
Install a new container immediately without cleaning the gun and follow item 3.1.
3.5. Cleaning the gun
Unscrew the container from the gun.
Place the spray tip on the cleaning agent container and clean the fresh foam residue on the gun.
Remove the spray tip and screw the cleaning agent container onto the gun. Proceed similarly to the instructions for the foam container (item 3.1.).
Fill the gun with a cleaning agent and leave for approx. 10 minutes.
Press the trigger lever again and clean the inside of the gun with a fresh cleaning agent.
Unscrew the cleaning agent container. Using a cloth, remove any remaining cleaning agent from the container/gun connection and apply a thin
layer of Vaseline.
Do not clean the gun with corrosive agents.
When using the gun continuously, clean it every 2 - 3 months as described above.
Product specificaties
| Merk: | Yato |
| Categorie: | Lijmpistool |
| Model: | YT-6745 |
| Gewicht: | 600 g |
| Type verpakking: | Doos |
| Kleur handvat: | Black, Orange, White |
| Materiaal: | Aluminium, Brass, Stainless steel |
| Aantal per verpakking: | 1 stuk(s) |
| Materiaal van het handvat: | PTFE |
| Coating materiaal: | Nikkel |
| Applicator van schuim: | Ja |
Heb je hulp nodig?
Als je hulp nodig hebt met Yato YT-6745 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden