WyreStorm EXP-EX-80-KVM Handleiding

WyreStorm AV extender EXP-EX-80-KVM

Lees hieronder de 📖 handleiding in het Nederlandse voor WyreStorm EXP-EX-80-KVM (4 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

HDMI KVM Extender Set

with USB 2.0 Extension

EXP-EX-80-KVM Quickstart Guide

EXP-EX-80-KVM Quickstart Guide | 200330

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

In the Box

1x EXP-EX-80-KVM Transmitter

1x EXP-EX-80-KVM Receiver

1x 12V DC 2A Power Supply (US/UK/EU/AU)

1x USB Type B to Type A Cable

4x Mounting Brackets

HDMI

HDMI Monitor/Display

Keyboard and Mouse

12V DC

Power Supply

Cat5e/6/6a/7

HDMI USB

USB

EXP-EX-80-KVM Transmitter (TX) EXP-EX-80-KVM Receiver (RX)

KEY

HDMI

Cat5e/6/6a/7

USB

Power

Personal Computer

Transmitter (Front/Rear) Receiver (Front/Rear)

HDMI In 19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

Power LED Solid: The unit is powered On

Off: The unit is powered Off

Power In

5.5mm Screw Down Barrel Jack

Connect to the included 12V DC 2A power

supply to the transmitter. A power supply

is not required on the other end as it will be

powered using PoC.

Status LED Flashing: The receiver is operating normally.

Off: The receiver is Not operating normally.

EUTP Out

8-pin RJ-45 female

Connect the transmitters UTP OUT to

receivers UTP IN.

FUSB LED

Solid: USB linked

Flashing: USB data transmitting

Off: No USB device connected

GUSB (PC) Host USB Type B female

Connection of USB Host device

HDMI Out 19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

Power LED Solid: The unit is powered On

Off: The unit is powered Off

Power In

5.5mm Screw Down Barrel Jack

Connect to the included 12V DC 2A power

supply to the transmitter. A power supply

is not required on the other end as it will be

powered using PoC.

Status LED Flashing: The receiver is operating normally.

Off: The receiver is Not operating normally.

EUTP In

8-pin RJ-45 female

Connect the transmitters UTP OUT to

receivers UTP IN.

FUSB LED

Solid: USB linked

Flashing: USB data transmitting

Off: No USB device connected

GUSB Device

2x USB Type A female

Connection of USB devices such as

keyboards and mice.

EXP-EX-80-KVM Quickstart Guide | 200330

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

A B C D E F G A B C D E F G

EXP-EX-80-KVM Quickstart Guide | 200330

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device

• Verify that all HDMI and UTP connections are not loose and are functioning

properly

• Verify that the UTP cable is properly terminated following EIA568B standard

• Verify that the output resolution of the source and display is supported by

this extender

Failed USB Connection or Slow Transmission rate

• Ensure the category cable length is within the range of requirement, USB HID

device is within 80m/260ft, USB storage device is within 60m/200ft.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

Product specificaties

Merk:	WyreStorm
Categorie:	AV extender
Model:	EXP-EX-80-KVM
Kleur van het product:	Zwart
Soort:	Zender en ontvanger
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Meegeleverde kabels:	USB
Aantal USB 2.0-poorten:	3
Certificering:	CE, FCC, RoHS, RCM, EAC
Resolutie (maximum digitaal):	1920 x 1080 Pixels
Temperatuur bij opslag:	-20 - 70 °C
Luchtvochtigheid bij opslag:	10 - 90 procent
Maximaal bereik:	80 m
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Code geharmoniseerd systeem (HS):	84733080
Inclusief bevestigingsbeugel:	Ja
Zender breedte:	75 mm
Zender diepte:	98.2 mm
Zender hoogte:	23 mm
Receiver gewicht:	220 g
Transmitter gewicht:	220 g
Stroomverbruik (zender) (max):	3.6 W
Ondersteundende kabel types:	Cat6, Cat6a, Cat7, HDMI
Receiver breedte:	75 mm
Diepte van de receiver:	98.2 mm
Receiver hoogte:	23 mm
Poorttype zender video:	HDMI
Poorttype zender lokaal toetsenbord/muis:	USB
Stroomverbruik (ontvanger) (max):	3.6 W
Poorttype ontvanger lokale video:	HDMI
Poorttype ontvanger lokaal toetsenbord/muis:	USB
Aantal RJ-45-poorten (ontvanger):	1
Aantal RJ-45-poorten (zender):	1