WyreStorm SW-510-TX Handleiding

WyreStorm AV extender SW-510-TX

Lees hieronder de 📖 handleiding in het Nederlandse voor WyreStorm SW-510-TX (4 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

SW-510-TX Quickstart Guide | 191212

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the

installation process.

Basic Wiring Diagram

Personal Computer

SW-515-RX

Laptop Local Monitor

USB

Mic/Speaker

Deskplate

12V DC 1.5A

Power Supply

KEY

HDMI/DisplayPort/USB-C

HDBaseT/Ethernet

RS-232/Relay

Analog Audio

Analog Video

USB 2.0

4-input 4K UHD Switching HDBaseT Transmitter

with USB host/device (4K: 100m/328ft)

SW-510-TX Quickstart Guide

IMPORTANT! Installation Requirements

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

Information and Parts Required for Installation

This transmitter requires connection via RS-232 or Ethernet in order to

congure functions such as EDID. Ensure that the following items are on hand

before proceeding with the installation.

• PC or Mac

• Telnet and Terminal software such as PuTTY

• USB COM Port Adapter (Not Included)

• WyreStorm Part: CAB-USB-3PIN

• Network router and/or switch if using IP telnet for conguration.

• Latest version of the SW-510-TX API for advanced conguration not

covered in this document.

In the Box

1x SW-510-TX Transmitter

1x 12V DC Power Supply (US/UK/EU)

1x IR Receiver

2x Mounting Brackets

1x 3-pin Screw Down Phoenix Connector

1x 4-pin Screw Down Phoenix Connector

1x Quickstart Guide (This Document)

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its

entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable transmitters, kinks in cables,

and electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends using pre-terminated VGA, HDMI, DP and USB

cables due to the complexity of these connector types. Using pre-

terminated cables will ensure that these connections are accurate and will

not interfere with the performance of the product.

• This product contains a USB-C connection that can be used as an audio/

video input. When using this connection verify that the USB-C cable used

supports audio/video functionality as not all USB-C cables support this

requirement.

Communication Connections

RS-232 Wiring

The SW-510-TX uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

PC Connection

Connection to a PC uses the RS-232 Control connection and requires the use

of a USB to 3-pin Port Adapter cable (CAB-USB-3PIN) in order for a port to

be provided on the PC. Note that this adaptor can be used on both v1 and v2

versions.

RS-232 Passthrough

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

RS-232 Control

3rd Party Device

Pin 1 V DC Out No Co ection Reserved12 nn

Pin 2 TX (Transmit) > To > RX (Receive)--- ---

Pin 3 RX (Receive) > To > TX (Transmit)--- ---

Pin 4 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Audio Connections

Audio In

The audio connections use a 3.5mm (1/8in) TRS Stereo Jack.

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device.

• Verify that all HDMI and HDBaseT connections are not loose and are

functioning properly.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this transmitter.

• Congure EDID Settings to a lower resolution.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR, RS-232, and Ethernet cables are properly terminated

following the section.Wiring and Connections

Relays Not Functioning

• Verify polarity of the relay connections.

Troubleshotting Tips

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

SW-510-TX Quickstart Guide | 191212

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Setup and Conguration

The SW-510-TX is congured using RS-232 commands for Output Resolution, and EDID. Follow these steps to properly congure the transmitter based on the

system requirement.

Note: The steps and information provided in this QSG are for basic operation of the transmitter out of the box. Refer to the SW-510-TX API for full conguration

settings.

1. Assign a Static IP Address to ensure proper communication on an IP Network.

2. Set EDIDs to be used at each input of the device. See Conguring Input EDIDs

Communication Settings

The commands listed below can be sent by connecting to either the TX or

RX for RS-232 and the RX only for Ethernet. Each device must be connected

together via HDBaseT in to order to send a command from one device to the

other. The only exception is which requires Conguring a Static IP Address

connection to the RX.

The SW-510-TX contains a web UI that can be accessed by connecting to a

network and entering the IP address. We recommend that the IP address is

changed from default before accessing the web UI for the rst time.

RS-232 and IP Settings

Baud rate: 115200

Data Bits: 8bits

Parity: None

Stop Bits: 1bit

Flow Control: None

Default IP Address 192.168.11.43

Default IP Port 23

Conguring Input EDIDs

By default, all inputs are set to an EDID or 1920x1080@60Hz 2CH. However, this can be congured to suit the installation.

SW-510-TX Quickstart Guide | 191212

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Set Input EDID

SET EDID [Input] [Resolution] [Device]<CR><LF>

Example: SET EDID in1 1 tx<CR><LF>

Response: EDID SET in1 1 tx<CR><LF>

Query Input EDID

GET EDID [Input] [Device]<CR><LF>

Example: GET EDID in1 tx<CR><LF>

Response: EDID GET in1 1 tx<CR><LF>

Resolution={Below tables based on connection}

VGA EDID HDMI/USB-C EDIDs

1024x768@60Hz 2CH 1024x768@60Hz 2CH

1280x768@60Hz 1280x720@60Hz

1360x768@60Hz 1360x768@60Hz

1440x900@60Hz 1440x900@60Hz

1600x900@60Hz 1600x900@60Hz

1680x1050@60Hz 1680x1050@60Hz

1920x1080@60Hz 1920x1080@60Hz

1920x1200@60Hz 3840x2160@30Hz

Product specificaties

Merk:	WyreStorm
Categorie:	AV extender
Model:	SW-510-TX
Kleur van het product:	Zwart
Gewicht:	970 g
Breedte:	263 mm
Diepte:	148.7 mm
Hoogte:	45.5 mm
Soort:	AV-zender
LED-indicatoren:	Ja
Stroom:	2 A
Ondersteund audioformaat:	LPCM, PCM
USB-connectortype:	USB Type-A, USB Type-B, USB Type-C
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Ondersteunde video-modi:	1080p, 2160p
Maximum resolutie:	4096 x 2160 Pixels
Vermogensverbruik (max):	14.02 W
Aantal USB-aansluitingen:	6
Certificering:	CE, FCC
HDCP:	Ja
Aansluiting voor netstroomadapter:	Ja
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080),1920 x 1200 (WUXGA),3840 x 2160,4096 x 2160
Duurzaamheidscertificaten:	RoHS
Aantal DisplayPorts:	1
VGA (D-Sub) invoer ports:	1
Aantal per verpakking:	1 stuk(s)
DisplayPorts in:	1
Temperatuur bij opslag:	-20 - 70 °C
Luchtvochtigheid bij opslag:	10 - 90 procent
HDBaseT-gecertificeerd:	Ja
Lijningang:	Ja
HDMI in:	1
RS-232 ingangspoorten:	2
HDCP versie:	2.2
Bandbreedte:	9.2 Gbit/s
Aantal HDMI-uitgangen:	1
RJ-45 invoer ports:	2
Operating voltage:	12 V
Aansluiting video:	HDMI/VGA/DisplayPort
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Ondersteundende kabel types:	Cat6, Cat6a, Cat7, HDMI
3,5 mm in:	Ja
Extended display identification data (EDID):	Ja