Wilbur Curtis Alpha5Gt Handleiding

Wilbur Curtis Koffiezetapparaat Alpha5Gt

Lees hieronder de 📖 handleiding in het Nederlandse voor Wilbur Curtis Alpha5Gt (8 pagina's) in de categorie Koffiezetapparaat. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

Models Included

 •ALPHA1GT

 •ALPHA2GT

 •ALPHA2GTW

 •ALPHA3GT

 •ALPHA3GTR

 •ALPHA3GTL

 •ALPHA4GT

 •ALPHA5GT

 •ALPHA5GTR

 •ALPHA5GTL

 •ALPHA6GT

 •ALPHA6GTN

CAUTION:DONOT

connect this brewer to hot

water.Theinletvalveis

not rated for hot water.

CAUTION:Pleaseuse

this setup procedure

before attempting to use

this brewer. Failure to follow the

instructions can result in injury or the

voidingofthewarranty.

ISO9001REGISTERED

Important Safeguards/Conventions

Service Manual, Alpha G3 - Decanter Brewer

For the Latest speciFications and inFormation go to www.wiLburcurtis.com

This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an autho-

rized Wilbur Curtis service center.

 •DoNOTimmersetheunitinwateroranyotherliquid

 •Toreducetheriskofreorelectricshock,doNOTopentoporrearpanel.Nouserserviceablepartsinside.Repairshould 

be done only by authorized service personnel.

 •Keephandsandotheritemsawayfromhotpartsofunitduringoperation.

 •Nevercleanwithscouringpowders,bleachorharshimplements.

Conventions

WARNINGS–Tohelpavoidpersonalinjury

ImportantNotes/Cautions–fromthefactory

SanitationRequirements

YourCurtisADSSystemisFactoryPre-SetandReadytoGo…RightfromtheCarton.

FollowingaretheFactorySettingsforyourALPHA™GT

CoffeeBrewingSystems:

•BrewTemperature=200°F

 •BrewVolume=Settodispensingvesselrequirements(60oz)

 •WarmerSettingonHIGHwithQualityTimerOFF

GenerallytherewillneverbeareasontochangeyourG3programming.However,shouldyouneedtomakeslightadjustmentstomeet

yourbrewingneeds,programminginstructionsareprovidedlaterinthismanual.

 SystemRequirements:

  •WaterSource20–90PSI.Musthaveaminimumowrateof GPM(preferredowrateis1gpm).½

  •Electrical:Seeattachedschematicforstandardmodelorvisitwww.wilburcurtis.comforyourmodel.

Equipmenttobeinstalledtocomplywithapplicablefederal,state,orlocalplumbing/electricalcodeshavingjurisdiction.

SETUPSTEPS

Theunitshouldbelevel(lefttorightandfronttoback),locatedonasolidcountertop.Connectawaterlinefromthewaterltertothe

brewer.NOTE:Sometypeofwaterltrationdevicemustbeusedtomaintainatrouble-freeoperation.(Inareaswithextremelyhard

water,wesuggestthatasedimentaryandtaste&odorlterbeinstalled.)Thiswillprolongthelifeofyourbrewingsystemandenhance

coffeequality.

1.A3/8”NPTx1/4”Flareelbowhasbeensuppliedforwaterlineconnection.Usetubingsizedsufcientlytoprovideaminimumof 

½ gallon per minute.

2.Connecttheunittoanappropriateelectricalpowercircuit.

3.Turnonthetoggle(STANDBY/ON)switchbehindtheunit.Theheatingtankwillstarttoll.Whenthewaterlevelinthetankrises 

tothecorrectvolume,theheatingelementswillenergizeautomatically.WithADSSystemsthereisnodangerofelementburnout 

causedbyanemptytank.

4.Theheatingtankwillrequire20to30minutestoreachoperatingtemperature(200°F)asindicatedbyREADY-TO-BREWdisplayed

ontheLED.

5.Priortobrewing,dispense12ouncesofhotwaterthroughthehotwaterfaucet.

6. Brewacycleofatleast12ounces,topurgethewaterlinesofanyairthatmaybetrappedafterlling.

BREWINGINSTRUCTIONS

 1.BrewershouldbeON(Conrmatreartoggleswitch,thenpressON/OFFbutton).Ready-to-Brewshouldbedisplayed.

 2.Placeemptydecanter(notincludedwithAlphabrewer)onwarmerplate.

 3.Placeanewlterinbrewcone.

4.Pourground

coffee into

  brewcone.

6. PressBrew

button.

W C C , i .ilbur urtis ompany nC

5. Position

 brewcone

 intobrew

rails.

WILBURCURTISCOMPANY

Montebello,CA90640

CAUTION:When

cleaning,DONOTuse

powders, liquids, cleans-

ers, or any substance containing

chlorine.Theseproductspromote

corrosion, cause pitting of

stainlesssteelandwillvoidthe

warranty.

NSF International requires the following water connection:

1. Aquickdisconnectoradditionalcoiledtubing(atleast2xthedepthoftheunit)sothatthemachinecanbemovedfor 

cleaning underneath.

2. Insomeareasanapprovedbackowpreventiondevicemayberequiredbetweenthebrewerandthewatersupply.

Find out more

on the web

www.wilburcurtis.com

Brew Volume

SelectingBrewbyVolumeorBrewbyTimedependsonwhetheryouknowyourbrewtimebeforestarting.FromProgramMenuspress>displaywillnowshow

thenextfeature.

Duringtheactualbrewcycle,a2-minutedripmodeisaddedtothebrewtime.Theprogrammedwaterlevelcompensatesforbacktobackbrewing

Delta3toallowforanincreaseofwatervolume.

Brew by Volume (Factory set to 60 oz.): Press toSelect,DisplaywillnowshowPushSTARTToBegin...PresstheBREWbuttonthenhotwaterstartsrun-

ning,whendesiredvolumeisreachedpressBREWbuttonagaintostoptheow.Nowthevolumehasbeenset.Pressing>buttonwilldisplaythesubsequent

menu features.

Brew by Time (Factory set to 2min–40sec).Press toSelecttochangethebrewtime.Displaywillnowshowthecurrenttime.Bypressing<or>youcan

togglebackandforthfromminutestosecondstoexit(ex).Changethetimeorsetandexitbypressing.

Temperature (Factory set to 200°F) Press toSelect.Press<or>tomovetodesiredtemperatureandthen  to set. Temperature is programmable from

170ºFto204ºF,in2-degreeincrements.

Energy Save Mode (Factory set to OFF)Press toSelect,<or>ON,OFForON140ºF, toset.WheninON,unitwillautomaticallyshutoff4hours 

fromlastbrew.WhenfeatureisOFF,unitdoesnothavetheenergysavingmode.IntheON140ºFposition,temperaturegoesdownto140ºF.ifunithasnot

brewedin4hours.Thisfeaturewillsaveenergybyloweringthetanktemperatureduringperiodsofnon-operation.

Brew Count Odom. Press todisplaytotalgallonsbrewed.PressexorReset

Pre-Infusion (Factory set to OFF)Press toSelect.Currentsettinginsecondsisdisplayed<todecreaseorselect>toincrease(rangefromOFFto10

through60seconds), to set.

IfPre-infusionisselected(ON),ColdBrewLockissettoDelta1within5ºFofsetpointandColdBrewLockisdisappearsfromthelistofprogramselec-

tions.WhenPre-infusionisON,PulseBrewdisappearsfromthelistofprogramselections.

Quality Timer (Factory set to OFF)Press toSelect,<or>OFForON20minutesto120minutesin10minuteincrements.Press  to set. An audible

alarmwillsoundwhentimeisexpired.

Brew Count Total Press toSelect,Showstotalgallonsandtotalbrewcyclesontheunit.Isreadonlyandnotresettable

ToGoIntoProgramming

Turnoff(darkdisplay)bypressingON/OFFbutton(yellow).Pressand BREWbutton(green)andthenpressandreleaseON/OFFbutton(yellow).hold

ContinueholdingBREWbutton.Displaywillread ,waituntil isdisplayedEnterthe4-digitaccesscode,thedigits1-4correspondtothebut-

tons(seeillustrationbelow).

Thedefaultcodesetatthefactoryis1-2-3-4.Then willbedisplayed.

YourCurtisG3SystemisFactoryPre-SetforOptimumPerformance.

Afterconnectiontowaterandpower;thereartoggleswitchmustbeon.Youwillhearabeepsound,indicatingpowerisavailabletothecontroller.

Thecontroldisplays .PressON/OFFbuttonandthescreenwilldisplay .Afterthreeseconds, isdisplayed.

Waterwillllthetank(approximately2-3minutesdependingonwaterowrate).Whentheproperlevelisreached willappearonthescreen.Ittakesapproxi-

mately20minutestoreachsetpointtemperatureof200°F.

Controlwilldisplay whentemperaturereachesthesetpoint(200°F).Unitisnowreadytobrew.

CURTIS

CURTIS CURTIS

FILLING

CURTIS

HEATING

CURTIS

READYTOBREW

1 2 3 4

PROGRAM MENUS

ModelSelect–Alwaysperformthisrst.Thisfeaturere-setsallsettingstothefactorydefaults.

ScrollthroughthemenutoModelSelect.ThechoicesareALPHA-1, ALPHA-2, ALPHA-3/4/5, Airpot Brewer Thermo-Alphaand .YoushouldselectonlyALPHA-1,

ALPHA-2orALPHA-3/4/5.

Allprogrammingselectionsareperformedwiththethreecenterbuttons.

Thesymbolsbelowthebuttonsare:

 ScrollLEFT

 SELECTIONorENTERtosavenewparameter

  ScrollRIGHT

Cold Brew Lock . . . (Factory set to 15º)Press toselect,<or>toselectdesiredsetting(CBL5,15orOFF),  to set.

TheColdBrewLockfeatureallowsthebrewertobrewatthreedifferenttemperaturelevelsfromtheactualsetpoint.Therstsettingiswithin5degreesofset

point,nextiswithin15degreesofsetpoint,OFFiswithin30degreesofsetpointfortheReadytoBrewmessage,howeveritwillbrewatanytemperature.

ThisfeaturewilloperateafterinitializationtosettemperatureaftertherearstandbytoggleswitchisresettoON.

Master ResetPress todisplayAreYouSure?Then<forYes,>forNo.Brewerfactorydefaultsarethenreset.

Service Call (Phone number Factory set to [800] 995-0417) Press todisplaynumberandchangenumberor<tomoveplaceandEXtoexitwhen

completeThisnumberwillbedisplayedduringaHeatingsystemSENSORERRORorduringaWATERERROR.

Access Code (Factory set to 1-2-3-4) Press todisplaynumberandchangenumber,(thenumbercanbechange1to4)or<tomoveplaceandextoexit

whencomplete.

Banner Name (Factory set to CURTIS)Press todisplaylettersandchangelettersor<tomoveplaceandEXtoexitwhencomplete.Thisfeatureallows

upto14letterstobeprogrammedforcompanynameorregionalname.ProgrammingallblanksdisablesBannerName.

Warmers Auto OFF (Factory set to Disable) Press toSelect.Press<or>tomovetodesiredtimeandthen toset.Timerisprogrammablefrom2to4 

hoursinonehourincrementsorOFF.

P-Maintenance (Factory set to OFF)Press toSelect,SetgallonsbrewedtoindicateP-Maintenance.Press<or>toadjustfromOffto3000gallons.

Press toexit.

Beeper On/Off (Factory set to ON)Press todisplayONorOFF.Pressingeither<or>togglesbetweenonandoff.  to set.

Pulse Brew (Factory setting OFF) Press toselect,<or>toselectOFForoneofvepulsepatterns(AtoE).

Guidelines for Pulse Brew:

Thisfeatureallowstuningofthecoffeeavor.ThepotlevelshouldalwaysbesetrstwiththisoptionOFF.Dependingonyourgrindproleandwaterconditions,

thevePulseBrewoptionshelp“tune”orchangethecoffeeavor.FilterPacktypecoffeestypicallyextractbetterwiththeAandBpulsesetting.Decaffeinated

coffeestypicallyextractbetterwiththeBpulsesetting.High-YieldcoffeestypicallyextractbetterwiththeCpulsesetting.Ofcourse,anyoftheA,BorCsettings

maybeusedtosuityourtasteprole.Therearetwoadditionalsettings(DandE)thatallowyoutomanuallysettheONTIMEpulsesandOFFTIME.

IfPulseBrewisselected(ON),ColdBrewLockissettoDelta1within5ºFofsetpointandColdBrewLockdisappearsfromthelistofprogramselec-

tions.WhenPulseBrewisON,Pre-infusiondisappearsfromthelistofprogramselections.

Display Brew Time (Factory set to ON).Press todisplayONorOFF.Pressingeither<or>togglesbetweenonandoff. toset.Whenon,theDisplay 

BrewTimefeatureallowsyoutoseetheremainingtimeinthebrewcylecountingdown.

Drip-Out Mode (Factory set to 2 min) Press toselect.Press>toincreasetime(toamaximumof5minutes)or<todecreasethetimeandturnOFF.

Timecountsupin5secondincrements.Press to set.

Model SelectPress toselect,<or>toselectmodel.Theselectionsare:ALPHA-1,ALPHA-2,ALPHA-3/4/5,AirpotBrewer,Thermo-Alpha(fortheD60GT).

Press toset.WhentheModelSelectfeatureischanged,allsettingsareresettothedefaultsofthenewlyselectedmodel.

ExitPress toselect,exitsprogrammodeandreturnsunittooperation.

Warmer Temperature Control

TurnonbreweratthecontrolpanelON/OFFbutton.WarmerbuttonshouldbeOFF(LEDoff).PressandholddesiredWARMERbutton.Screenwilldisplaycur-

rentsettingin%ofpower.Press<or>toincreaseordecreasepowertowarmer(50%to100%in10%increments).Press to set.

Tank Temperature Check

TurnonbreweratthecontrolpanelON/OFFbutton.Pressandhold3button(seeillustration,page2)for5seconds.WaterTemperaturewillbedisplayed.

Thetemperaturewillnotdisplaywhiletheunitisintheprocessreheating.

NOTE:Alpha3GTONLY;whencheckingtanktemperature,rstmakesureREARwarmerisON(redLEDon)andthenpress3for5secondstodisplay

tanktemperature.

Brew Volume – Easy Access

UnitsproducedbeginningJanuary2008canbeeasilyadjustedfromthefrontpanel.WrittenintothesoftwareontheAlphaGTUCM,isafeaturetoaccessthe

brewvolumewithoutenteringtheprogrammode.

TheUCMmustbeon.ToadjusttheALP1GTmodels,pressandholddownthecenter,Selectbutton2.Thescreenwillread pressing<or>

willadjustthebrewvolumeupordown,±20oz,in1ounceincrements.

Onanymulti-stationAlpha(ALP2/3/4/5/6GT):PressthecenterSelectbutton2twice,withthesecondpressholddownthebuttonforaroundve[5]seconds.

Thescreenwilldisplay pressing<or>willadjustthebrewvolumeupordown,±20oz,in1ounceincrements.

Vol.Adj.<-0>Oz.

-Select+

Vol.Adj.<-0>Oz.

-Select+

PROGRAM MENUS