Whirlpool WDFS3R4P Handleiding
Pagina's 8 Engels Wasmachine
Bekijk de handleiding van Whirlpool WDFS3R4P gratis online of download de PDF. 183 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
1
ENDaily Reference Guide
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixedprogram button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Crystals program button with indicator light
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
FIRST TIME USE
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Half Load) button for 3 seconds until you hear
abeep.
3. After one second the rst available setting (letter „h”) will be displayed.
4. Press button to scroll through the list of available settings (see
table below), then press START/Pause to view and change the value
of the currently selected setting.
5. Press to change the value, then press START/Pause to save the
new value.
6. To change another setting, repeat points 2 and 5.
7. Press ON-OFF or wait 30 seconds to exit the menu.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 0,5 kg); it is not un-
usual for alittle water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water sof-
tener beyond repair).
Run aprogram every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in aperfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
The factory setting is “3”. See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
LETTERSETTING
VALUES
(Default - in bold)
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 | 4 | 5
NaturalDry(see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as aresult of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on the heater, contributing also to better cleaning ef-
ciency. This system regenerates itself with salt, therefore it is required
to rell the salt container when empty. Thefrequency of regeneration
depends on the water hardness level setting - regeneration takes place
once per 4-6 Eco cycles with the water hardness level set to 3. The regen-
eration process occurs at the beginning of the cycle with additional fresh
water.
• Single regeneration consumes: ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser Ashould be
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with adry cloth.
3. Press the lid down until you hear aclick to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
Amaximum of 6 levels can be set according to the dishwasher model.
• If you see bluish streaks on the dishes, set alow number (0-3).
• If there are drops of water or limescale marks on the dishes, set
amid-range number (4-5).
A
B
12. Program number and remainingtime indicator
13. Closedwater tap indicator light
14. DESCALE indicator light
15. Power Clean® option button with indicator light
16. Half Load option button with indicator light/ Settings - 3 sec. press
17. Extra Dry option button with indicator light
18. Silent option button with indicator light/ Key lock - 3 sec. press
19. Sani Rinse option button with indicator light
20. Self-Clean program button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (soft)0 - 60 - 100 - 7
2 (medium)7 - 1111 - 208 - 14
3 (average)12 - 1621 - 2915 - 20
4 (hard)17- 3430 - 6021 - 42
5 (very hard)35 - 5061 - 9043 - 62
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: whirlpool.com.au
After installation, please remember to remove all transport
protection parts from the dishwasher.
1
234
5
6
7
8
9
10
111213
14
1516171819202122
CONTROL PANEL
THANK YOU FOR BUYING AWHIRLPOOL PRODUCT.
In order to receive amore complete assistance, please
register your appliance on: whirlpool.com.au
Foutcodes Whirlpool WDFS3R4P
Foutcodes uit de officiële handleiding, met betekenis en oplossing.
| Code | Betekenis | Oplossing | Pagina |
|---|---|---|---|
| F6 E1 | Bedieningspaneel reageert niet of heeft een communicatiestoornis | 1. Schakel het apparaat uit door op de ON-OFF/Reset knop te drukken. 2. Wacht ongeveer één minuut. 3. Schakel het apparaat weer in en start het programma opnieuw. 4. Als het probleem aanhoudt, trek de stekker uit het stopcontact. 5. Wacht één minuut en steek de stekker weer in. 6. Start het programma opnieuw. | 5 |
| F7 E3 | De vaatwasser kan het water niet afvoeren - verstopping in afvoersysteem | 1. Controleer of het afvoerslang geknickt is en zet het recht (zie installatiehandleiding). 2. Maak het filter schoon van voedselresten en kalk (zie reinigingshandleiding). 3. Controleer of de gootsteen afvoerpijp niet verstopt is en maak deze schoon indien nodig. 4. Voer de descalingstappen uit. | 5 |
| F8 E3 | De vaatwasser beëindigt de cyclus voortijdig - afvoer- of schuimprobleem | 1. Controleer of het filter verstopt is met voedselresten of kalk en maak het schoon. 2. Controleer of het afvoerslang op de juiste hoogte is geplaatst (zie installatiehandleiding). 3. Controleer of het afvoersysteem in het huishouden sifoning veroorzaakt en installeer indien nodig een sifon breaker. 4. Controleer of er overmatig schuim aanwezig is: gebruik de juiste hoeveelheid en type afwasmiddel. 5. Herhaal de cyclus zonder extra afwasmiddel toe te voegen. | 6 |
| F8 E5 | Ventiel is geblokkeerd of defect | 1. Sluit de waterkraan af, indien mogelijk. 2. Schakel de stroomvoorziening NIET uit. 3. Neem contact op met de servicedienst (telefoonnummer in garantieboekje). | 6 |
| F9 E1 | De vaatwasser kan het water niet afvoeren - afvoerprobleem | 1. Maak het filter schoon van voedselresten en kalk (zie reinigingshandleiding). 2. Controleer of het afvoerslang geknickt is (zie installatiehandleiding). 3. Verwijder verstoppingen in de gootsteen afvoerpijp. 4. Voer een descalingprogramma uit. | 5 |
Alle foutcodes Whirlpool Wasmachine
Product specificaties
| Merk: | Whirlpool |
| Categorie: | Wasmachine |
| Model: | WDFS3R4P |
Heb je hulp nodig?
Als je hulp nodig hebt met Whirlpool WDFS3R4P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Wasmachine Whirlpool
Whirlpool FFB 9469 WV SPT Handleiding Whirlpool Pure 2486 Handleiding Whirlpool WDFS3L5P Handleiding Whirlpool WDFS3R4N Handleiding Whirlpool WB90805 Handleiding Whirlpool Champion 1400 Handleiding Whirlpool FDLR80250 Handleiding Whirlpool ZEN FSCR70421 Handleiding
Alle Whirlpool Wasmachine handleidingen
Populair in Wasmachine
Whirlpool AWO 164U2 - 6TH SENSE Handleiding Whirlpool FFB 8469 BV BE Handleiding Whirlpool W8W846WR IT Handleiding
Handleiding Wasmachine
Nieuwste handleidingen voor Wasmachine
BEKO B3WFT6104012WBC SPT Handleiding BEKO TB721DBVESPL Handleiding LERAN WMS 12800 WD3 Handleiding Hisense WD3I1143BTL Handleiding BEKO BMWRU3821W Handleiding BEKO B1W73235SMA Handleiding BEKO WDI85DAW_IT Handleiding BEKO BM3WFU6843 Handleiding BEKO BMWG10147EB Handleiding BEKO B3WFT684012WBC SPT Handleiding