Whirlpool WDFS3R4P Handleiding

Bekijk gratis de handleiding van Whirlpool WDFS3R4P (8 pagina’s), behorend tot de categorie Wasmachine. Deze gids werd als nuttig beoordeeld door 182 mensen en kreeg gemiddeld 5.0 sterren uit 6 reviews. Heb je een vraag over Whirlpool WDFS3R4P of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

ENDaily Reference Guide

1. ON-OFF/Reset button with indicator light

2. Eco program button with indicator light

3. Auto Intensive program button with indicator light

4. Auto Mixedprogram button with indicator light

5. Auto Fast program button with indicator light

6. Rapid program button with indicator light

7. Crystals program button with indicator light

8. Prewash program button with indicator light

9. Salt reservoir empty indicator light

10. Rinse Aid reservoir empty indicator light

11. Display

FIRST TIME USE

SETTING MENU

1. Switch on the appliance by pressing the ON-OFF button.

2. Hold the Settings (Half Load) button for 3 seconds until you hear

abeep.

3. After one second the rst available setting (letter „h”) will be displayed.

4. Press button to scroll through the list of available settings (see

table below), then press START/Pause to view and change the value

of the currently selected setting.

5. Press to change the value, then press START/Pause to save the

new value.

6. To change another setting, repeat points 2 and 5.

7. Press ON-OFF or wait 30 seconds to exit the menu.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and on

the machine’s functional components.

The salt reservoir is located in the lower part of the dishwasher (under the

lower rack on the left side).

• It is mandatory that the salt reservoir never be empty.

• It is important to set the water hardness.

• Salt must be lled when the SALT REFILL indicator light on the con-

trol panel is lit.

1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Position the funnel (see gure) and ll the salt reservoir

right up to its edge (approximately 0,5 kg); it is not un-

usual for alittle water to leak out.

3. Only the rst time you do this: ll the salt reservoir

with water.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly so that no detergent can get into

the container during the wash program (this could damage the water sof-

tener beyond repair).

Run aprogram every time as soon as you completed relling the salt

reservoir to avoid corrosion.

Setting the water hardness

To allow the water softener to work in aperfect way, it is essential that

the water hardness setting is based on the actual water hardness in your

house. This information can be obtained from your local water supplier.

The factory setting is “3”. See „WATER HARDNESS TABLE”.

To change, follow instructions in section “SETTING MENU”.

LETTERSETTING

VALUES

(Default - in bold)

Water Hardness Level

(see “SETTING THE WATER HARDNESS”

and “WATER HARDNESS TABLE”)

1 | 2 | 3 | 4 | 5

Rinse Aid Level

(see “ADJUSTING THE DOSAGE OF RINSE AID”)

0 | 1 | 2 | 3 | 4 | 5

NaturalDry(see “OPTIONS AND FUNCTIONS”)

“1” = On, “0” = O

1 | 0

Sound

“1” = On, “0” = O

1 | 0

Factory Settings

Press START/Pause to restore to the factory

default all the values of the settings included in

the settings menu.

-

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indicator

light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as aresult of limescale accumulation.

Use of salt is recommended with any type of dishwasher detergent.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently pre-

venting scale buildup on the heater, contributing also to better cleaning ef-

ciency. This system regenerates itself with salt, therefore it is required

to rell the salt container when empty. Thefrequency of regeneration

depends on the water hardness level setting - regeneration takes place

once per 4-6 Eco cycles with the water hardness level set to 3. The regen-

eration process occurs at the beginning of the cycle with additional fresh

water.

• Single regeneration consumes: ~3L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser Ashould be

lled when the RINSE AID REFILL indicator light in the control panel is lit.

1. Open the dispenser B by

pressing and pulling up the

tab on the lid.

2. Pour in the rinse aid (max.110

ml), making sure it does not

overow from the dispenser.

If this happens, clean the spill

immediately with adry cloth.

3. Press the lid down until you hear aclick to close it.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the dosage of rinse aid

If you are not completely satised with the drying results, you can adjust

the quantity of rinse aid used.

To change, follow instructions in the section “SETTING MENU”.

If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW

RINSE AID indicator light will not be lit if you run out of rinse aid.

Amaximum of 6 levels can be set according to the dishwasher model.

• If you see bluish streaks on the dishes, set alow number (0-3).

• If there are drops of water or limescale marks on the dishes, set

amid-range number (4-5).

A

B

12. Program number and remainingtime indicator

13. Closedwater tap indicator light

14. DESCALE indicator light

15. Power Clean® option button with indicator light

16. Half Load option button with indicator light/ Settings - 3 sec. press

17. Extra Dry option button with indicator light

18. Silent option button with indicator light/ Key lock - 3 sec. press

19. Sani Rinse option button with indicator light

20. Self-Clean program button with indicator light

21. Delay option button with indicator light

22. START/Pause button with indicator light

Water Hardness Table

Level

°dH

German degrees

°fH

French degrees

°Clark

English degrees

1 (soft)0 - 60 - 100 - 7

2 (medium)7 - 1111 - 208 - 14

3 (average)12 - 1621 - 2915 - 20

4 (hard)17- 3430 - 6021 - 42

5 (very hard)35 - 5061 - 9043 - 62

Before using the appliance carefully read

Safety and Installation Instructions. More information about your

product available on website: whirlpool.com.au

After installation, please remember to remove all transport

protection parts from the dishwasher.

1

234

5

6

7

8

9

10

111213

14

1516171819202122

CONTROL PANEL

THANK YOU FOR BUYING AWHIRLPOOL PRODUCT.

In order to receive amore complete assistance, please

register your appliance on: whirlpool.com.au

Product specificaties

Foutcodes Whirlpool WDFS3R4P

Foutcodes uit de officiële handleiding, met betekenis en oplossing.