Whirlpool WDFS3R4N Handleiding
Pagina's 8 Engels Wasmachine
Bekijk de handleiding van Whirlpool WDFS3R4N gratis online of download de PDF. 128 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
1
ENDaily Reference Guide
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixedprogram button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Crystals program button with indicator light
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
FIRST TIME USE
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Half Load) button for 3 seconds until you hear
a beep.
3. After one second the rst available setting (letter „h”) will be displayed.
4. Press button to scroll through the list of available settings (see
table below), then press START/Pause to view and change the value
of the currently selected setting.
5. Press to change the value, then press START/Pause to save the
new value.
6. To change another setting, repeat points 2 and 5.
7. Press ON-OFF or wait 30 seconds to exit the menu.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
The factory setting is “3”. See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
LETTERSETTING
VALUES
(Default - in bold)
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 | 4 | 5
NaturalDry(see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on the heater, contributing also to better cleaning ef-
ciency. This system regenerates itself with salt, therefore it is required
to rell the salt container when empty. Thefrequency of regeneration
depends on the water hardness level setting - regeneration takes place
once per 4-6 Eco cycles with the water hardness level set to 3. The regen-
eration process occurs at the beginning of the cycle with additional fresh
water.
• Single regeneration consumes: ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 6 levels can be set according to the dishwasher model.
• If you see bluish streaks on the dishes, set a low number (0-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
A
B
12. Program number and remainingtime indicator
13. Closedwater tap indicator light
14. DESCALE indicator light
15. Turbo option button with indicator light
16. Half Load option button with indicator light/ Settings - 3 sec. press
17. Extra Dry option button with indicator light
18. Silent option button with indicator light/ Key lock - 3 sec. press
19. Sani Rinse option button with indicator light
20. Self-Clean program button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (soft)0 - 60 - 100 - 7
2 (medium)7 - 1111 - 208 - 14
3 (average)12 - 1621 - 2915 - 20
4 (hard)17- 3430 - 6021 - 42
5 (very hard)35 - 5061 - 9043 - 62
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: whirlpool.com.au
After installation, please remember to remove all transport
protection parts from the dishwasher.
1
234
5
6
7
8
9
10
111213
14
1516171819202122
CONTROL PANEL
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: whirlpool.com.au
Foutcodes Whirlpool WDFS3R4N
Foutcodes uit de officiële handleiding, met betekenis en oplossing.
| Code | Betekenis | Oplossing | Pagina |
|---|---|---|---|
| F6 E1 | Bedieningspaneel reageert niet of er is een communicatiestoring | 1. Zet het apparaat uit met de ON-OFF/Reset knop. 2. Wacht ongeveer één minuut. 3. Zet het apparaat weer aan en start het programma opnieuw. 4. Als het probleem aanhoudt, trek de stekker uit het stopcontact voor 1 minuut en steek deze weer in. | 5 |
| F7 E3 | De afvoer werkt niet correct - mogelijk verstopte filter of afgeknikte afvoerslang | 1. Reinig het filter en verwijder voedselresten of kalkafzettingen (zie CLEANING THE FILTER ASSEMBLY). 2. Controleer de afvoerslang op kinkels (zie INSTALLATION INSTRUCTION). 3. Als nodig, ontklak het apparaat (zie DESCALE INSTRUCTION). 4. Controleer of de gootsteen afvoer niet verstopt is en reinig deze indien nodig. | 5 |
| F8 E3 | Afvoercyclus is voortijdig beëindigd - mogelijk probleem met afvoer of schuimvorming | 1. Controleer of het filter verstopt is en reinig het (zie CLEANING THE FILTER ASSEMBLY). 2. Controleer of de afvoerslang op de juiste hoogte is geplaatst (zie INSTALLATION). 3. Controleer op siphonering in het riolering en installeer een siphonbreker/luchttoevoerklep indien nodig. 4. Controleer of de juiste hoeveelheid afwasmiddel is gebruikt en herstart de cyclus. | 6 |
| F8 E5 | Klep is geblokkeerd of defect | 1. Sluit de waterkraan af indien mogelijk. 2. Zet de stroomtoevoer NIET uit. 3. Neem contact op met de servicedienst. | 6 |
| F9 E1 | De afvoer werkt niet correct - mogelijk verstopte filter of blokking in afvoersysteem | 1. Reinig het filter en verwijder voedselresten of kalkafzettingen (zie CLEANING THE FILTER ASSEMBLY). 2. Controleer de afvoerslang op kinkels (zie INSTALLATION INSTRUCTION). 3. Controleer of de sink afvoerpijp niet verstopt is en reinig deze indien nodig. 4. Ontklak het apparaat indien nodig (zie DESCALE INSTRUCTION). | 5 |
Alle foutcodes Whirlpool Wasmachine
Product specificaties
| Merk: | Whirlpool |
| Categorie: | Wasmachine |
| Model: | WDFS3R4N |
Heb je hulp nodig?
Als je hulp nodig hebt met Whirlpool WDFS3R4N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Wasmachine Whirlpool
Whirlpool Primo 1406 Handleiding Whirlpool FFB 9469 WV SPT Handleiding Whirlpool Pure 2486 Handleiding Whirlpool WDFS3L5P Handleiding Whirlpool WDFS3R4P Handleiding Whirlpool WB90805 Handleiding Whirlpool Champion 1400 Handleiding Whirlpool FDLR80250 Handleiding
Alle Whirlpool Wasmachine handleidingen
Populair in Wasmachine
Whirlpool AWO 164U2 - 6TH SENSE Handleiding Whirlpool FFB 8469 BV BE Handleiding Whirlpool W8W846WR IT Handleiding
Handleiding Wasmachine
Nieuwste handleidingen voor Wasmachine
BEKO BMSMW7126EB Handleiding Candy GD 410B9B-80 Handleiding Hoover HBP 49SBL10UC-80 Handleiding BEKO TB621DBVESPL Handleiding Bosch WGJ254A9NL Handleiding BEKO TB721DAVESCS Handleiding BEKO B3WFT6104012WBC SPT Handleiding BEKO TB721DBVESPL Handleiding LERAN WMS 12800 WD3 Handleiding Hisense WD3I1143BTL Handleiding