Velleman KNS8 Handleiding

Bekijk gratis de handleiding van Velleman KNS8 (8 pagina’s), behorend tot de categorie Speelgoed. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.8 sterren uit 9 reviews. Heb je een vraag over Velleman KNS8 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

KNS8 VELLEMAN 1

KNS8 – MECHANICAL SKELETON

1. Introduction & Characteristics

Thank you for buying the KNS8 ! Read this manual carefully before bringing the KNS8 into use.

• Build a gearbox and learn how automatic transmissions and motors work.

• Easy to build, no glue or soldering required.

• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper

included)

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

Note that the figures with the assembly instructions can be found in the second folder “KNS8 – Figures”!!!

2. Parts List (see also KNS8 – Figures)

Part n° Quant. Description Part n°Quant. Description

1 1 gearbox 18 6 nylon nut M3

2 1 motor 3Vdc 19 18 nut M2

3 1 battery holder 20 18 screw (2 x 8mm)

4 21 1 slide switch with wire 4 self-tapping screw (2 x 4mm)

5 22 1 metal shaft (2 x 40mm) 2 screw (3 x 14mm)

6 23 1 metal shaft (3 x 52mm) 2 screw (3 x 18mm)

7 1 pinion gear 8T 24 2 screw (3 x 22m)

8 25 1 face gear 36T/10T (white) 8 washer (3.2 x 10.0 x 0.5mm)

9 26 1 gear 40T/0T (white) 15 washer (2.6 x 6.0 x 0.5mm)

10 1 gear 40T/10T (red) 27 3 PVC tube (15mm)

11 1 gear 40T/10T (green) 28 10 nylon pad (Ø 8mm)

12 29 1 wire with terminal (yellow) 5 fixing plate (L-shaped)

13 30 1 wire with terminal (green) 4 nylon post (H : 3mm)

14 2 metal foot (U-shaped) 31 1 spring (L : 50mm)

15 32 2 nylon connector (N-shaped) 2 spring (L : 20mm)

16 2 nylon pad (5.6 x 4.8 x 1.95) 33 6 self-tapping screw (2 x 6mm)

17 2 nylon post (H : 6mm)

3. Prepunched Boards (see “KNS8 – Figures

”

)

4. Assembly (see also “KNS8 – Figures

”

)

Fig. 3 : The gears (n°9/10/11/8) should be placed to the left of the pinion gear. One N-shaped nylon connector

(n°15) should point downward and the other one upward. Insert the motor as depicted in the drawing. Note

that the protruding edge should point towards the metal case.

Fig. 4 : Identify boards 2 & 3. The screw opening in board 3 is located in the middle, while the one in board 2 lies

off to the left. Make sure board 1 is not upside-down.

Product specificaties