Velleman KNS4 Handleiding
Pagina's 7 Nederlands Speelgoed
Bekijk de handleiding van Velleman KNS4 gratis online of download de PDF. Deze handleiding is 19 keer bekeken. Vraag over dit model? Stel een vraag
KNS4 VELLEMAN 1
KNS4 – COPTERMECH
1. Introduction & Characteristics
Thank you for buying the KNS4 ! Read this manual carefully before bringing the device into use.
• Familiarise yourself with the operation of transmissions steered through gears or pulleys.
• Easy to build, no glue or soldering required.
• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
• The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS4 – Figures”!!!
2. Parts List
Part n° Quant. Description Part n°Quant. Description
1 1 motor holder
12 2 fixing plate
2 1 battery holder 13 3 PVC tube (1.5 x 15mm)
3 1 motor with wire 14 3 metal shaft (2 x 90mm)
4 15
1 slide switch with wire 3 metal shaft (2 x 70mm)
5 1 plastic tube (L : 15cm) 16 1 belt (black) (126 x 1mm)
6 17 1 metal shaft (2 x 40mm) 1 rubber band (35mm, red)
7 1 pinion gear 18 4 rubber band (40mm red)
8 19 1 face gear 36T/14T (white) 7 fixing plate (L-shaped)
9 20 2 pulley 19.5 x 2mm (blue) 15 nylon pad
10 8 pulley 15 x 2mm (yellow) 21
11 nylon pad
11 22 2 pulley 24 x 2mm (white) 26 self-tapping screw
3. Prepunched Boards (see “KNS4 – Figures
”
)
4. Assembly (see also “KNS4 – Figures
”
)
Fig. 4 : Insert part n°20 in the hole on board n°2 and mount the motor holder according to fig. 4.
Fig. 5 : Insert part n°20 (x 8) in boards n°1 & 4. Insert part n°7 between boards 1 & 4. Insert 2 x part n°15 in board
n°4 and through the pulley (part n°10). The metal shafts come out the other side of board n°1. Remember
to put the rubber bands (parts n°18 & 16) on the pulley before inserting the metal shaft. Another part n°15
goes through boards n°1 & 4.
Fig. 6 : Cut part n°5 to precisely 32mm. Insert part n°20 in board n°5 first, then put metal shaft n°14 through board
n°5. Mount part n°5 & 8 according to figure 6. Attach board n°5 to boards n°1 & 4 with part n°19.
Product specificaties
| Merk: | Velleman |
| Categorie: | Speelgoed |
| Model: | KNS4 |
| Breedte: | 357 mm |
| Diepte: | 264 mm |
| Hoogte: | 125 mm |
| Ondersteund aantal accu's/batterijen: | 2 |
| Thema: | Bouwkunde |
| Batterijen inbegrepen: | Nee |
| Type product: | Engineeringset |
Heb je hulp nodig?
Als je hulp nodig hebt met Velleman KNS4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden