VDO Dayton CD 2200 Handleiding

Bekijk gratis de handleiding van VDO Dayton CD 2200 (18 pagina’s), behorend tot de categorie Autoradio. Deze gids werd als nuttig beoordeeld door 32 mensen en kreeg gemiddeld 4.3 sterren uit 6 reviews. Heb je een vraag over VDO Dayton CD 2200 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

2

* Depending on version

•Blue lead A5 (Electronic/Motor Aerial) :

This radio can provide a 12V signal for the

control of an automatic motor aerial or the

supply of an electronic aerial by connection.

Do not use this connection for the supply lead

of the aerial motor!

•Orange lead A6 (Pilot light) : Connect to

the dashboard illumination wiring of the car.

When the car headlights are switched on, the

backlight to the power key remains illuminated

(even when the radio is switched off). When

the set is on with this connection , the

brightness of the display is reduced.

CONNECTOR B (fig.2)

Loudspeakers (use 4 ohm loudspeakers

only)

•Do not connect any of the loudspeaker leads

to earth or directly to a booster/amplifier or via

an external fader!

•Connecting 4 loudspeakers

FrontRear

Left+Green [B5]White [B7]

Left-Green/black [B6]White/black [B8]

Right+Grey [B3]Blue [B1]

Right-Grey/black [B4]Blue/black [B2]

–To check the loudspeaker connections keep

the 'SCAN' key pressed and switch on the set.

To cancel switch off the set.

BLUE CONNECTOR C * for a Digital CD

changer (available separately) (fig. 3)

•You can only connect the following CD changer

with a digital output to this set :

- CH0400 or CH0600 or CH1000

Useful tips

Recommended connection instructions between

the CD changer and headunit :

1.Ensure that the Connector A (power supply) is

removed from the headunit.

2. Finish all connections between the CD changer

(see mounting instructions for the CD changer)

and the headunit.

3. Reconnect the Connector A (power supply) to

the headunit.

INSTALLATION

If your car is equipped with ISO connectors,

simply insert them in connectors of the car radio.

If not, you can use an adaptor cable (Refer to the

table on the separate installation card). Ensure all

cables are installed so that they cannot be

damaged by sharp edges or moving parts.

PREPARATION

Voltage and polarity: The set must be connected

to a 12V car battery with negative terminal to

earth (car chassis). Installation in vehicles not

fulfilling these requirements could result in

malfunction, damage or fire.

Warning: To prevent short-circuiting, disconnect

the negative car battery terminal until the set has

been mounted and connected (fig.1 See separate

installation card).

CONNECTOR A (fig.2)

POWER SUPPLY CONNECTIONS

•Red lead A7 : Connect to a permanent 12V

supply. This is the main power supply. Ensure

this connection can handle a current of 10A.

•Yellow/red lead A4 : Connect to a switched

12V supply (switched on/off by car ignition).

•Brown lead A8: Connect to earth (car

chassis).

This connection set up will enable you to make

full use of the ON/OFF LOGIC function of this set

limiting the use of the set to 1 hour after removal

of the ignition key. If this feature does not appear

to be functioning as expected you may require

an adapter cable (EA6259). See reverse of

installation card.

OPTIONAL CONNECTIONS (fig. 2)

•Pink lead A1 * (SDVC AND SPEED

WARNING) :

Speed Dependent Volume Control

automatically increases and decreases the

volume as a result of the car's speed.

Speed Warning can be used to inform you that

you are exceeding a certain speed.

•Connect pin A1 to a signal from the

speedometer of your car. Some cars are

already prepared for it (e.g. certain VW &

Vauxhall/Opel cars), please consult your dealer.

If not, you may need a more detailed

installation requiring extra equipment to

enable your car to become compatible.

This can only be accomplished by persons

familiar with automotive electrical and

mechanical systems. After connection see

‘SPECIAL FUNCTIONS’.

Complies with 21 CFR 1040.10

Product specificaties