Valcom V-BBP Handleiding
Pagina's 4 Niet gecategoriseerd
Bekijk de handleiding van Valcom V-BBP gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
19474010
CAUTION: To reduce the risk of electric shock,
Do not remove cover.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Issue 1
V-GUARDIAN ALERT
V-P V-Guardian Beacon BB
INTRODUCTION
The V-BBP V-Guardian Beacon is a component of the V-
Guardian Alert system. It is a wireless beacon, using
Bluetooth Low Energy technology, that provides location
information to the V-Guardian Alert Badge.
Features
•Uses Bluetooth Low Energy technology
•Small, unobtrusive packaging
•Supervision capable (with additional components)
•Status LED
SPECIFICATIONS
Power Requirements
24Vdc, 50 mA
Dimensions/Weight
1.173.” H” Diam.22x .1 (0cm H 5.4cm Diam.) x
Weight 0.1 lbs ( 45g)
Environment
Temperature:0 to +50°C
Humidity: 0 to 80% (non-precipitating)
Indoor installation only.
IMPORTANT SAFETY INFORMATION
CONSIGNES DE SÉCURITÉ IMPORTANTES
1. Read these instructions.
Lisez ces instructions.
2. Keep these instructions.
Conservez ces instructions.
3. Heed all warnings.
Respectez tous les avertissements.
4. Follow all instructions.
Suivez toutes les instructions.
5. Do not use this apparatus near water.
Ne pas utiliser cet appareil près de l'eau.
6. Clean only with dry cloth.
Nettoyer avec un chiffon sec.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Ne pas bloquer les ouvertures de ventilation. Installer formément aux instructions du
fabricant.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
Ne pas installer à proximité de sources de chaleur telles que radiateurs, registres de
chaleur, poêles ou autres appareils (y compris les amplificateurs) produisant de la chaleur.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade and the third prong are provided for your safety. If
the provided plug does not fit into your outlet consult an electrician for replacement of the
obsolete outlet.
Ne pas contourner le dispositif de sécurité de la fiche polarisée ou de mise à la terre. Une
fiche polarisée possède deux lames dont une plus large que l'autre. Une fiche de terre a
deux lames et une troisième broche de mise à la terre. La lame large et la troisième
broche sont fournies pour votre sécurité. Si la fiche fournie ne rentre pas dans votre prise,
veuillez consulter un électricien pour le remplacement de la prise obsolète.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
N'utilisez que des fixations / accessoires spécifiés par le fabricant.
12. Use only with the cart, stand, tripod, bracket or table specified
by the manufacturer or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
Utilisez uniquement avec le chariot, stand, trépied, support ou table spéc
fabricant ou vendu avec l'appareil. Quand un chariot est utilisé, Soyez prudent lorsque
vous déplacez l'ensemble chariot / appareil pour éviter des blessures dues au
renversement.
13. Unplug this apparatus during lightning storms or when unused for a long period of time.
Débranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilisé pendant une
longue période de temps.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way. Such as when the power supply cord or plug is
damaged, liquid has been spilled, objects have fallen into the apparatus or the
apparatus has been exposed to rain or moisture and does not operate normally or has
been dropped.
Confiez toute réparation à un personnel qualifié. Une réparation est nécessaire lorsque
l'appareil a été endommagé de quelque façon. Par exemple lorsque le cordon
d'alimentation ou la fiche est endommagé, du liquide a été renversé, si des objets sont
tombés dans l'appareil ou le appareil a été exposé à la pluie ou à l'humidité et ne
fonctionne pas normalement ou s'il est tombé.
2 10 94740
Precautionary Designations
•WARNING-To Reduce The Risk Of Fire Or Electric
Shock. Do Not Expose This Apparatus To Rain Or
Moisture
•AVERTISSEMENT - Afin de réduire les risques
d'incendie ou de décharge électrique, évitez
d'exposer le système à la pluie ou à l'humidité.
•Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
•L’appareil ne doit pas être exposé à des
égouttements et éclaboussures et aucun Objet
Rempli de liquide, comme vase, ne doit être placé
sur l’appareil.
FCC Information
Contains FCC ID: 2AO94-MK14
1. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
2. any Changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
INSTALLATION
Mounting
The V-BBP can be wall or ceiling mounted.Before
mounting, twist the cover of the V-BBP counterclockwise
to separate the cover from the base.
Wall or other Hard Surface Mount: The base has screw
holes at the top and bottom near the edge of the base.
Route the power wires and (optional) supervision wiring
through the base.If using surface wiring, a breakaway
tab is provided at the top of the base to route the wiring
into the base.Use appropriate screws (not provided) to
attach the base to the surface. Refer to Figures 1A and
1B.
NOTE: The hole in the center of the base is for the V-
BBMC-5 ceiling grid mounting clip. Do not use this
hole for attachment with screws or other fasteners.
Suspended Ceiling Grid with V-BBMC: For suspended
tile ceilings, optional mounting clips are available as part
number V-BBMC-5 (5 pack). The clips facilitate mounting
to the ceiling grid main beam or cross tee.Attach the V-
BBMC clip to the ceiling grid following the instructions
included with the V-BBMC. The V-BBP base is attached
to the clip using the large hole in the center of the base.
Position the hole in the base on the machine screw
extending from the bottom of the clip. Use the threaded
knob provided with the V-BBMC to secure the base to the
clip. Route the wiring through the ceiling tile and base.
See Figure 2.
Wiring Connections
Attach power wires and optional supervision wires to the
screw terminals of the V-BBP using the connection
diagram shown in Figure 3. Refer to the section for
Installing Multiple Beacons for details on supervision
wiring.
Supervision Jumper
If the V-BBP Beacon is connected to a VIP-BBH for wiring
supervision, the supervision jumper (JP3) must be set
properly. See the following instructions for Installing
Multiple Beacons for details.
After the base has been securely mounted and wiring
connections made, replace the cover on the base by
lining up the tabs of the V-BBP cover with the slots in the
base and twisting clockwise to secure. The tabs Note:
and slots are different sizes so that the cover will only
properly attach one way.
Installing Multiple Beacons
Multiple V-P Powered Beacons may be installed by BB
daisy-chaining them from a power and supervision
source. This is typically done using the VIP-BBH V-
Guardian PoE Power Hub.The Hub provides power and
supervision for up to 11 V-BBP Beacons.
3 10 94740
Power connections are made in parallel from the 24vdc
power source. Supervision wiring is made with two wires.
A common (ground) is connected in parallel from the
source to each V-BBP beacon. The signal wire is
connected serially from the source to the “In” connection
of the first Beacon, then from the “Out” connection of that
Beacon to the “In” of the next Beacon in the line. See the
diagram in Figures 3 & 5.The supervision jumper, JP3, is
installed on the pair of pins furthest from the wire
terminals for Beacons installed in-line. The last Beacon in
the line requires the jumper to be moved to two pins the
nearest to the wiring terminals. See the diagrams in
Figure 4.
Setup and Status
Configuration of the V-P Beacon is performed using BB
the cell phone application provided by Valcom, or through
the Site Manager server.The V-BBP indicates it is
receiving power by illuminating a Green LED, which is
visible through the small hole in the center of the cover.
TECHNICAL ASSISTANCE
When trouble is reported, verify that power is being
supplied to the unit and there are no broken connections.
If a spare unit is available, continue to troubleshoot by
substituting the spare unit for the suspected defective
unit.
Assistance in troubleshooting is available from the factory.
When calling, you should have a VOM and other
equipment necessary for troubleshooting.
Call (540) 563-2000 or visit our website at
http://www.valcom.com.
The V-P Beacon is not field repairable. Valcom, Inc. BP
maintains service facilities in Roanoke, VA. Should
repairs be necessary, attach the company name, address,
phone number, contact person and the nature of the
problem. Send the unit to:
Valcom, Inc.
Repair and Return Dept.
5614 Hollins Road
Roanoke, VA 24019-5056
WARRANTY
Warranty information may be found on our website at
www.valcom.com/warranty
Figure 1A. Wall Mounting
Figure 2. Ceiling Tile Mounting
Figure . Wall Mounting 1B
Product specificaties
| Merk: | Valcom |
| Categorie: | Niet gecategoriseerd |
| Model: | V-BBP |
Heb je hulp nodig?
Als je hulp nodig hebt met Valcom V-BBP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden