Uline H-12267 Handleiding
Pagina's 24 Niet gecategoriseerd
Bekijk de handleiding van Uline H-12267 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
PAGE 1 OF 24 1225 IH-12267
1-800-295-5510
uline.com
LAB WORKSTATION
H-12267, H-12268
TOOLS NEEDED
13 mm Wrench
12 mm Wrench
PARTS
PARTS
#DESCRIPTIONQTY.
AUnderboarding 12
BUnderboarding 21
CLeg2
DSupport Panel2
EFoot with Leveling Pad4
FUpright2
GTabletop1
10 mm SocketImpact Driver with Socket Adapter
+
h
A
B
C
E
G
F
D
8 mm Washer x 13
#28 1/4-20 x 1/2"
Blunt-end
Wood Screw x 10
M6 Nut x 1
M8 Nut x 8
Connection
Plate x 1
M6 x 16 mm Bolt x 1
M8 x 65 mm Bolt x 13
M8 x 16 mm
Bolt x 13
Hardware Kit
J
K
L
N
P
M
O
Q
Two Person
Assembly Required
Para Español, vea páginas 9-16.
Pour le français, consulter les pages 17-24.
+
Drill with 1/8" Drill Bit
7 mm Wrench
Phillips
Screwdriver
Caster x 4
H
ST6.3 x 25 mm
Screw x 14
I
If attaching phenolic top, only use blunt-end wood screws
packaged with tabletop.
CAUTION! Pointed-end screws packaged with steel frame
will protrude through phenolic top and are to be used with
stainless steel tabletops only.
CAUTION! Some parts may have sharp edges. Take care
when handling pieces to avoid injury. For your safety,
wear work gloves when assembling.
NOTE: Hardware packs are included in frame packaging.
Accessories will include their own hardware in packaging.
PAGE 2 OF 24 1225 IH-12267
LEGS AND FRAME ASSEMBLY
1. Flip legs (C) upside down and place underboarding (A)
on outside of legs. Align holes in underboarding to holes
in legs. Secure with eight M8 x 16 mm bolts (J) using a
12 mm wrench. (See Figure 1)
2. Place underboarding (B) at back side of frame
between legs (C) and align with threaded holes in
legs. Secure to legs with four M8 x 16 mm bolts (J)
using a 12 mm wrench. (See Figure 1)
NOTE: Front of frame (A) will have Uline label on
underboarding.
3. If attaching shelf, place two support panels (D)
between legs (C) in the back and center locations
of leg. Align threaded holes in support panels with
holes in legs. Secure support panels to legs with two
M8 x 65 mm bolts (K) and two 8 mm washers (M) per
support panel using a 13 mm wrench. (See Figure 2)
NOTE: If not attaching shelf, only one support
panel is needed and can be attached in the
back or center leg location.
NOTE: Figures 2-8 show assembly with both
support panels installed.
4. Place feet (E) into legs (C) and slide to desired height.
Fasten feet to legs with two M8 x 65 mm bolts (K), two
8 mm washers (M) and two M8 nuts (L) per leg using a
13 mm wrench for bolts and nuts. (See Figure 3)
NOTE: Tabletop adds 1-1⁄" to overall
workbench height.
NOTE: If removing pre-installed leveling
pad and attaching casters, account for an
additional 2⁄" to overall workbench height.
5. If using casters (H), unscrew pre-installed leveling
pad from each foot (E). Screw casters (H) into
threaded inserts in the feet (E). (See Figure 4)
ASSEMBLY
Figure 1
C
A
C
A
J
J
B
Figure 2
D
C
C
K
D
M
Figure 3
E
C
C
K
M
L
Figure 4
H
E
PAGE 3 OF 24 1225 IH-12267
6. Place tabletop on a smooth, non-marring surface
with top side facing down.
NOTE: Backside of tabletop has corner cutouts.
(See Figure 5)
If attaching phenolic top, only use blunt-end
wood screws packaged with tabletop.
7. With assembled frame upside down, align holes in
frame with pre-drilled holes in the tabletop. Attach
tabletop (G) to frame underboarding and legs with
10 ST6.3 x 16 mm screws (I) for stainless steel top or
10 #28 1/4-20 x 1/2" blunt-end wood screws (O) for
phenolic top. Secure with impact driver and 10 mm
socket bit or Phillips screwdriver. (See Figure 5)
8. To prevent table from rolling when turning upright,
turn red dial on casters counterclockwise to lower
anti-vibration pad. To make table mobile again,
turn red dial clockwise until pad has fully risen.
(See Figure 6)
9. Turn frame assembly upright. Loosen four M8 x 16 mm
bolts (J) on backside of the workstation frame with a
12 mm wrench. (See Figure 7)
10. Align upright (F) keyhole slots between previously
loosened bolts and frame. Re-tighten the four
M8 x 16 mm bolts (J) with a 12 mm wrench to secure
uprights to frame. (See Figure 8)
ASSEMBLY CONTINUED
Figure 5
G
I or O
Figure 7
J
Figure 8
J
F
Figure 6
Red
Dial
Caster
Anti-Vibration Pad
RAISEDLOWERED
Product specificaties
| Merk: | Uline |
| Categorie: | Niet gecategoriseerd |
| Model: | H-12267 |
Heb je hulp nodig?
Als je hulp nodig hebt met Uline H-12267 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden