Uline H-8023 Handleiding
Pagina's 9 Niet gecategoriseerd
Bekijk de handleiding van Uline H-8023 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
PAGE 1 OF 9 0126 IH-8022
1-800-295-5510
uline.com
IBC TANK HEATER
π H-8022, H-8023
The controller plugs into the GFCI-protected power
supply (wall, etc.). The controller will power up when
power supply cord is plugged in.
The IBC tank heater plugs into the output receptacle
cord of the controller. The controller regulates power
to the receptacle depending upon the temperature of
the probe/sensor versus the OFF and ON temperatures
programmed into the controller.
NOTE: Place the temperature sensor between
the blanket and the IBC. (See Figure 1)
CAUTION! Improper probe placement can
result in unsatisfactory performance and/or
damage to your vessel, product or blanket.
(See Figure 2)
CAUTION! Do not submerge the temperature
sensor – it is not waterproof. (See Figure 2)
Figure 1
Figure 2
OPERATION
Input Power Supply Cord
Gray temperature sensor lead with
steel encased temperature
sensor/probe (6' long)
Hanger Kit
Controller
Output Cord
with Connector
(2' long)
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
PAGE 2 OF 9 0126 IH-8022
OPERATION CONTINUED
Figure 3 is an example application where the system is
completely set up.
Please note:
• The controller is plugged into an approved GFCI
circuit protector, which is plugged into an approved
extension cord (not shown).
• The temperature sensor is placed between the
heated wrap and the outside of the IBC.
• The heated wrap is plugged into the output
receptacle of the controller.
• The controller is hanging from the top strap of the
heated wrap.
• Removeable vinyl top is placed over the top of the
IBC.
• The system is positioned on a solid, wood-topped
pallet to reduce heat loss out of the bottom of the IBC.
The controller is programmed at the factory to be in its
heating mode and to turn the heater OFF at the OFF set
temperature and turn it back ON when the temperature
of the probe/sensor reaches the ON set temperature.
Unless in the programming mode, the display shows the
current temperature of the probe. It is important to note
that the temperature of the contents in the vessel will
lag this displayed temperature. This amount may vary
depending on application. As the contents in the vessel
approach the desired temperature this difference will
be much less.
The green light will glow when there is power to the
output receptacle and go off when the power is not
connected to the receptacle. There should be an
audible click as the controller turns the power to the
output receptacle on or off.
To program the thermostatic controller to the new OFF
and ON temperatures, press MENU. The controller is
now in programming mode. With OFF flashing, push
MENU again. The controller will flash the current OFF
temperature. Use the UP and DOWN arrow buttons to
increase or decrease the temperature set point, one
degree per push. When the correct OFF temperature is
flashing on the display, press MENU again. This scrolls
the controller to the ON variable. Press MENU again
to access the ON variable. Use the UP or DOWN arrow
buttons to increase or decrease the temperature set
point, one degree per button push. Press MENU again
to exit the ON variable. Press the UP or DOWN arrows
simultaneously again to exit the programming mode.
The display will revert to a steady display of the present
temperature of the probe/sensor.
CAUTION! Do not program the controller to
OFF > 170°F, as this may damage the heating
blanket, vessel and/or product.
NOTE: If the unit is not heating, confirm the OFF
temperature is higher than the ON temperature.
When in heating mode, a flame will appear in
the bottom right corner of the screen.
Figure 3
PAGE 3 OF 9 0126 IH-8022
PROGRAMMABLE CONTROL FUNCTIONS
PROGRAMMABLE CONTROL FUNCTIONS
Off (Relay OFF Temperature) – Settable temperature
at which the controller will turn off the heating blanket.
Range: -40° to 212°F.
On (Relay ON Temperature) – Settable temperature at
which the controller will turn on the heating blanket.
Range: -40° to 212°F.
ASd – Anti-Short Cycle Delay – Preset to zero minutes,
this is the wait time before the controller does anything
after plugged in or after the power comes back on in
the case of a temporary power outage. For example,
ASd is useful when running a cooling pump where a
quick power outage or temperature cycle will stall the
compressor and it won't safely restart until the pressure
has equalized in the system, which can take several
minutes. For heaters, there is no reason to wait to restart
the system.
SF – Sensor Failure Operation – This is preset to zero,
which has the effect of turning off the heater in the
rare case of sensor failure. Set this to one if user wants
to run full power without temperature control if sensor
malfunctions.
F or C – Temperature Units – The units can be switched
from Fahrenheit to Celsius or back by pressing the UP
and DOWN arrows simultaneously.
To change the values of any of these variables (except
F or C), press and hold MENU until SP flashes on the
screen, then release MENU. The controller is now in the
programming mode. Use the UP or DOWN arrow to scroll
to the desired function. Push MENU again to show the
present value of that function. Use the arrow buttons
to select the new value, then press MENU again to
make that the new value in memory. If MENU key is not
pressed within 30 seconds, the controller will exit the
programming mode and the value will not be changed.
ADDITIONAL CONTROLLER INFORMATION
NEMA/UL 4X – Watertight enclosure.
120VAC GHT2002J (A419AEC), 15 Amps max for heating
blankets.
More information via "A419 Series Electronic Temperature
Controls with NEMA 1 or NEMA 4X Watertight Enclosures"
also included with the controller.
1
-800-295-551
0
une.comli
OPERATION CONTINUED
FOLDING INSTRUCTIONS
NOTE: Avoid creasing and crumpling when
folding the blanket. Fold lines should have an
arch to prevent damage to the product.
NOTE: Only fold the blanket as many times as
necessary to prepare for storage. Excessive
folding and creasing may damage the
product.
NOTE: Never fold the blanket hot to hot. Never
roll up the product.
1. Lay the blanket out flat with the logo facing up.
2. Fold edges into center. (See Figure 4)
3. Fold blanket in half once more. (See Figure 5)
Figure 4
Figure 5
Product specificaties
| Merk: | Uline |
| Categorie: | Niet gecategoriseerd |
| Model: | H-8023 |
Heb je hulp nodig?
Als je hulp nodig hebt met Uline H-8023 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden