Tripp Lite Isobar PDUMH20-ISO Handleiding

Tripp Lite Stekkerdoos Isobar PDUMH20-ISO

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite Isobar PDUMH20-ISO (20 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20
1
Metered Rack PDU with
® Surge Protection
PDUMH15-ISO
(Series Number: AGIB7403)
PDUMH20-ISO
(Series Number: AGIB7410)
Important Safety Instructions 2
Important Warnings 2
Installation 3
Features 4
Warranty & Product Registration 6
Español 7
Français 13
Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2020 Tripp Lite. All rights reserved.
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR
surge protector in our monthly drawing!
tripplite.com/warranty
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed
during the installation, operation and storage of this product. Failure to
heed these instructions and warnings will void the product warranty.
Important Warnings
The PDU provides surge and line noise protection to connected equipment through its outlets.
The PDU is designed for indoor use only, in a controlled environment, away from excess
moisture, temperature extremes, conductive contaminants, dust or direct sunlight.
The PDU must be installed by a qualified technician only.
Do not attempt to mount the PDU to an insecure or unstable surface.
Install in accordance with National Electrical Code standards. Be sure to use the proper
overcurrent protection for the installation, in accordance with the plug/equipment rating.
Connect the PDU to an outlet that is in accordance with your local building codes and that is
adequately protected against excess currents, short circuits and earth faults.
The electrical outlets supplying power to the equipment should be installed near the equipment
and easily accessible.
Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that
eliminate the connection to ground.
Be sure to provide a local disconnect device on any models that are permanently installed
without a plug that is easily accessible.
Never attempt to install electrical equipment during a thunderstorm.
Individual equipment connected to the PDU should not draw more current than the individual
PDU’s outlet’s rating.
The total load connected to the PDU must not exceed the maximum load rating for the PDU.
Do not attempt to modify the PDU, input plugs or power cables.
Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable
parts inside.
Do not attempt to use the PDU if any part of it becomes damaged.
Use of this equipment in life support applications where failure of this equipment can
reasonably be expected to cause the failure of the life support equipment or to significantly
affect its safety or effectiveness is not recommended. Do not use this equipment in the
presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
3
Installation
Note: The illustrations may differ somewhat from your PDU model.
1-1
1-3
1-2
1-4
A
B
1 Determine Installation Configuration.
The PDU supports four primary installation
configurations: 1U Rack, 0U Rack, Wall
and Under-Counter. Choose a
configuration and follow the installation
instructions in the appropriate section of
Step 1 before proceeding to Step 2.
Note: Regardless of installation
configuration, the user must determine
the fitness of hardware and procedures
before mounting. The PDU and included
hardware are designed for common rack
and rack enclosure types and may not be
appropriate for all applications. Exact
mounting configurations may vary.
1-1 1U Rack Installation. Attach the PDU to
the rack by inserting four user-supplied
screws ( ) through the PDU mounting A
brackets ( ) and into the mounting holes B
of the rack rail as shown.
1-2 Remove 0U Rack Installation. Part 1:
the screws ( ) attaching the mounting C
brackets to the PDU, change the
orientation of the brackets as shown and
reattach the brackets. Use only the screws
supplied by the manufacturer or their
exact equivalent (#6-32, 1/4” flat head).
Part 2: Attach the PDU vertically by
inserting two or more user-supplied screws
(A) through the PDU mounting brackets
(B) and into mounting points in the rack
or rack enclosure.
1-3 After repeating Part 1 Wall Installation.
above, attach the PDU to a stable
mounting surface by inserting two or more
user-supplied screws ( ) through the PDU A
mounting brackets ( ) and into secure B
mounting points on the mounting surface.
1-4 Under-Counter Installation. After
repeating Part 1 above, attach the PDU to
a stable mounting surface by inserting four
user-supplied screws ( ) through the PDU A
mounting brackets ( ) and into secure B
mounting points on the mounting surface.
C
C
A
A
B
B
C
A
B


Product specificaties

Merk: Tripp Lite
Categorie: Stekkerdoos
Model: Isobar PDUMH20-ISO

Heb je hulp nodig?

Als je hulp nodig hebt met Tripp Lite Isobar PDUMH20-ISO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Stekkerdoos Tripp Lite

Handleiding Stekkerdoos

Nieuwste handleidingen voor Stekkerdoos