TP Link Kasa Smart KS225P3 Handleiding
TP Link
Niet gecategoriseerd
Kasa Smart KS225P3
Bekijk gratis de handleiding van TP Link Kasa Smart KS225P3 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 3.8 sterren uit 3 reviews. Heb je een vraag over TP Link Kasa Smart KS225P3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
Wire Your Switch
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to the dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
Note: If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the and wires.Ground Neutral
1
2
Identify and wires. Line Load
3
Line up the dimmer switch with the
mounting holes. Secure it with screws.
5
Attach the wallplate and the wiring is
nished. Then turn on the circuit
breaker.
6
Flip the page over to complete setup.
Power
Source
To Light
1) the circuit breaker. Use a voltage detector Turn on
to identify the energized wire ( ). Line wire
2) the circuit breaker. Label the and Turn o Line Load
wires.
Take care to avoid electric shocks.
Load wireLine wire
Product Introduction
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
This is a Matter-certied device. You can integrate
it into any Matter ecosystem you prefer for easy
control.
How to Set Up
A Matter-supported and of the controller smart home app
same ecosystem are required.
1. Turn on Bluetooth on your phone.
2. Open your selected smart home app and enter
the provided numeric setup code on your device
or scan the Matter QR code on the provided label.
3. Follow the instructions in the app to complete
setup.
Note: Setup processes may vary between ecosystems.
Set Up with Matter
Failed to Set Up?
1. Try to connect your phone to a stable Wi-Fi 2.4 GHz
network with internet access instead of a 5 GHz
network.
2. Press the Restart button once to restart your device.
3. Refer to the FAQ for detailed instructions:
https://www.tp-link.com/support/faq/3520/
Smart Wi-Fi Dimmer Switch
Quick Start Guide
©2023 TP-Link 7106510019 REV1.0.0
*Images may dier from your actual product.
Set Up Your Switch
STEP 2
SET UP
Tap the button in the app and select Smart
Switches > Smart Dimmer Matter. Then follow
the step-by-step app instructions to set up
your smart dimmer switch.
DOWNLOAD APP
Get the app from the App Store Kasa Smart
or Google Play.
STE 1P
OR
Appearance
On/O
Button
Decrease/Increase
Brightness
Restart
LED
Reset
Brightness
Indicators
Button Explanations
LED Status
Restart
Reset
Press to restart your dimmer switch.
Decrease or increase the brightness.
/
Starting up.Solid amber
Blinking amber
Blinking green
White
Solid red
Stay green for 30s
Blinking amber & green
Connecting to Wi-Fi.
Ready for setup;
Resetting Wi-Fi.
Device resetting.
Light fixture is off.
Disconnected from Wi-Fi.
Connected to Wi-Fi.
Press and hold for about until the LED 5s
blinks amber and green to reset Wi-Fi
while keeping other settings.
Press and hold for about until the 10s
LED blinks amber to restore to factory
default settings.
Specications
Rating: 120V~ 60Hz
Load: 300W Incandescent, 150W LED
Operation temperature:
32°F~104°F (0~40 ℃)
Method of mounting included: Independently mounted
(Vertically position only);
Operating control, Type 1 action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1
Before installing, servicing or removing the switch, read and follow all safety
precautions including the following:
• CAUTION – Risk of Electric Shock – More than one disconnect switch may be
required to de-energize the equipment before servicing. A circuit breaker which
disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power
is o at the circuit breaker before removing or installing any switch. Use a
non-contact voltage tester to ensure the power is o.
• The Smart Switch must be installed and used in accordance with the National Electric
Code (NEC) or your local electrical code. If you are unfamiliar with these codes and
requirements, or are uncomfortable performing the installation, consult a qualied
electrician.
• Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
• Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm,
W > 1.81 in./46 mm, D > 2 in./51 mm).
• Tighten terminal screws to 13 lbf-in.
Safety Notice
For technical support, the user guide and other information, visit
https://www.tp-link.com/support.
Support
High Voltage-Disconnect power supply before servicing
CAUTION
Haute tension. Débrancher l'alimentation électrique avant
d'utiliser
MISE EN GARDE
Product specificaties
| Merk: | TP Link |
| Categorie: | Niet gecategoriseerd |
| Model: | Kasa Smart KS225P3 |
Heb je hulp nodig?
Als je hulp nodig hebt met TP Link Kasa Smart KS225P3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd TP Link
7 Mei 2025
7 Mei 2025
7 Mei 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
14 April 2025
20 Februari 2025
27 Januari 2025
Handleiding Niet gecategoriseerd
- TVLogic
- Lumag
- Leitz
- Brainstorm
- Taqua
- Plustek
- Argus
- STI
- Trigano
- Thule
- True
- Califone
- Unold
- Ondis24
- HeadRush
Nieuwste handleidingen voor Niet gecategoriseerd
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025