Theben RAM 751 Handleiding

Bekijk gratis de handleiding van Theben RAM 751 (1 pagina’s), behorend tot de categorie Thermostaat. Deze gids werd als nuttig beoordeeld door 33 mensen en kreeg gemiddeld 4.2 sterren uit 7 reviews. Heb je een vraag over Theben RAM 751 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1. Applications

The electronic floor temperature controller is used for

controlling electric:

• direct floor heating

• floor temperature conditioning systems

Features

• Nighttime set-back, input for external clock

• Indicator lamps for "controller calls for heat" and for

set-back operation

• 2-pole mains switch

• Mounting in 60mm flush-type box

2. Description of functions

2.1 Functions

The floor temperature is set via the dial and is measured

by the remote sensor.

The scale of *…5 corresponds to a temperature of

10…50 °C.

Lamps

Red:Controller calls for heat

Green:Set-back mode is activated

2.2 Functions of the set-back input TA

The TA input is used to set various set-back functions,

refer to table below.

The functions are selected via the mains sine half-waves.

The functions correspond to the "Pilot wire" specificati-

on.

Caution-1!

The device may only be opened and installed ac-

cording to the circuit diagram on the device or these

instructions by a qualified electrician. The existing

safety regulations must be observed.

In order to comply with safety class II, the necessary

installation steps must be taken.

This independently mountable electronic device is de-

signed for controlling the temperature in dry and en-

closed rooms only under normal conditions. The devi-

ce confirms to EN 60730, it works according operating

principle 1C

468 931 003 454



Mounting and

Operating Instructions

Electronic floor temperature controller

with set-back input

RAM 751

Half-wave Function

noneno set-back

bothset-back acc. to J2

positivecontrol off

negativeanti-freeze = 10°C

both pulsed shortset-back by 1°C

both pulsed longset-back by 2°C

The anti-freeze function regulates to a temperature of

10°C.

This multi-function input makes it possible to activate

controller functions by means of the various half-waves

of the mains AC voltage:

Normal operation: input open– – – –

Temp. set-back: both half-wavesÄ

Anti-freeze: negative half-waveÅ

Heating off:positive half-wave Ç

2.3 Selecting the set-back temperature

By means of the J2 jumper it is possible to select 3°

or 5°.

J2 closedset-back by 5°C (factory pre-set)

J2 openset-back by 3°C

The temperature set externally via the dial is reduced by

this value.

2.4 Fault of the floor sensor

If a sensor fault (short-circuit or break) occurs, the con-

troller will switch to fault mode. The heating will func-

tion with max. 30% of the energy (operation for 30% of

the time). This provides frost- and overheat protection.

In the event of a sensor fault, both lamps will flash.

2.5 Function of the lamps

FunctionLamp greenLamp red

Heating is onon

Set-back modeon

Floor sensor faultflashesflashes

3. Electrical connection

Perform the steps described below:

• Pull off the temperature dial

• Release the fixing screw

• Remove the upper part of the casing

• Connect acc. to circuit diagram (see bottom of casing)

Floor sensor F 193720

The remote sensor must be mounted in such a way that

the temperature to be limited can be correctly re-

corded.

The remote sensor should be installed in a protective

tube. This will facilitate future replacement.

Do not install the sensor close to power lines. In other

cases a shilded cable has to be used.

The sensor can be extended to max. 50 m by means of

a cable suitable for mains voltage.

Caution!

The sensor lines are on mains voltage (230V).

Caution! De-energize the electric circuit first

4. Technical data

Order designationRAM 751

EDP No.:751 0 131

Temperature setting range:

Floor temperature*…5 (= 10…50ºC)

Indicator lamp redController calls for heat

greenSet-back temperature

Power switch2-pole

Supply voltage230V AC (195…253V) 50Hz

OutputRelay make contact

Switching current100mA…16A cos= 1;ϕ

100mA…4A cosϕ= 0.6

Control algorithmProportional controller

(similar to continuous

through PWM)

Switching temperature

differential ~1°C

Temperature sensorType F 193720 (length 4 m,

can be extended to max.50 m)

Temperature set-back3K or 5K selectable s. 2.3

vie external timer

Range limitationin the dial

Degree of protection

of casing IP 30

Safety classII (see Caution-1)

Degree of pollution2

Software classA

Calculation impulse voltage2,5 kV

Temperature for the

Ball compression test75°C

Voltage and Current for

the for purposes of inter-

fernce measurements230V, 0.1A

Ambient temperature0…40ºC

Storage temperature–25…70ºC

Weight90 g

Characteristics for remote sensor

10°C66.8 k30°C26.3 kΩ Ω

20°C41.3 k40°C17.0 kΩ Ω

25°C33 k50°C11.3 kΩ Ω

5. Circuit diagram

Position of the jumpers

6. Dimensions

Theben AG · Hohenbergstr. 32

72401 Haigerloch · DEUTSCHLAND

Fon+49 (0)7474/692-0

Fax+49 (0)7474/692-150

Service

Fon+49 (0)7474/692-369

Fax+49 (0)7474/692-207

hotline@theben.de

Adresses, telephone numbers etc.

at www.theben.de

cover 2 parts (50x50)

for conduit boxes

according to DIN 49073

Product specificaties