Supermicro SuperServer SYS-220P-C9RT Handleiding

Supermicro Server SuperServer SYS-220P-C9RT

Lees hieronder de 📖 handleiding in het Nederlandse voor Supermicro SuperServer SYS-220P-C9RT (1 pagina's) in de categorie Server. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
S/N: S 123 456XXX0 123
BMC: XXXXXXXXXXXX
PWD: AMBWODMRGT
http://www.supermicro.com MNL-2243-QRG
SuperServer 220P-C9R(T) Quick Reference Guide
CPU/Heatsink Installation Front View & Interface
Caution
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
CAUTION
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
For more information go to : http://www.supermicro.com/support
!
!
!
Rear View
System Information
Rev. 1.0
12
3
Jumper Description
Open (Normal)CMOS ClearJBT1
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
Pins 1-2 (Normal)
Audio EnableJPG1
ME RecoveryJPME1
JPME2
JVRM1/ JVRM2 VRM SMB (to BMC or PCH) Pins 1-2 (BMC, Normal)
JWD1 Watch Dog Timer Enable
Note 1: Intel Optane PMem 200 Series is supported by the 3rd Gen Intel Xeon Scalable Processor
(83xx/63xx/53xx/4315) Series only.
Note 2: P1-DIMMB2/P2-DIMMB2 memory slots are reserved for Intel Optane PMem 200 Series only.
Note 3: Memory speed support depends on the processors used in the system.
Mem ry rt 3r te ca cesso Suppo for the d Gen In l Xe Son la e Probl or
Type Ranks Per DIMM & DIMM Capacity (GB)
Data Width 1DPC (1-DIMM
Speed (MT/s); Voltage (V);
Slot Per Channel (SPC) and DIMM Per Channel (DPC)
Per Channel)
2DPC (2-DIMM Per
Channel)
8Gb 16Gb 1.2V 1.2V
RDIMM
SRx8 8GB 16GB
3200 2933*
SRx4 16GB 32GB
DRx8 16GB 32GB
DRx4 32GB 64GB
RDIMM-3DS (4R/8R)X4 2H-64GB
4H-128GB
2H-128GB
4H-256GB
LRDIMM QRx4 64GB 128GB 3200 3200
LRDIMM-3DS (4R/8R)x4 4H-128GB 2H-128GB
4H-256GB 3200 3200
Va ix DI S S i )lid ionat Matr (DDR4 MM w/PMem 200 er es
Ranks Per DIMM
DIMM Type & Data Width
(Stack)
DIMM Capacity (GB)
DRAM Density
8Gb 16Gb
RDIMM
(up to 3200)
1Rx8 N/A N/A
1Rx4 16GB 32GB
2Rx8 16GB 32GB
2Rx4 32GB 64GB
RDIMM 3DS
(up to 3200)
4Rx4 (2H) N/A 128GB
8Rx4 (4H) NA 256GB
LRDIMM (up to 3200) 4Rx4 64GB 128GB
LRDIMM 3DS
(up to 3200)
4Rx4 (2H) N/A N/A
8Rx4 (4H) 126GB 256GB
Heats NK- 0078ink S P P (for U2 CP )
Heats NK- 0078ink S P PC (for U1 CP )
Note: Thermal grease is pre-applied on new heatsinks. No additional thermal grease is needed.
Note: Unbalanced configuration (not recommended due to decreased performance)*
Memory Population Table (w/18 Slots)
Memory Population Sequence
CPU1: P1-DIMMA1
CPU1: P1-DIMMA1/P1-DIMME1
CPU1: P1-DIMMA1/P1-DIMME1/P1-DIMMC1
CPU1: P1-DIMMA1/P1-DIMME1/P1-DIMMC1/P1-DIMMG1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMME1/P1-DIMMC1/P1-DIMMG1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1/P1-DIMMH1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1/P1-DIMMH1 +
(P1-DIMMB2: for Pmem200 series)
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1/P1-DIMMH1 +
(P1-DIMMB2: for Pmem200 series)
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMMD1/P2-DIMME1/P2-DIMMF1/P2-DIMMC1/P2-DIMMG1/P2-DIMMH1 +
(P2-DIMMB2: for Pmem200 series)
Memory Population Sequence
CPU1: P1-DIMMA1
CPU2: P2-DIMMA1
CPU1: P1-DIMMA1/P1-DIMME1
CPU2: P2-DIMMA1/P2-DIMME1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMME1/P1-DIMMF1
CPU2: P2-DIMMA1/P2-DIMME1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMME1/P1-DIMMF1
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMME1/P2-DIMMF1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMME1/P2-DIMMF1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMME1/P2-DIMMF1/P2-DIMMC1/P2-DIMMG1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1/P1-DIMMH1
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMME1/P2-DIMMF1/P2-DIMMC1/P2-DIMMG1
CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMC1/P1-DIMMG1/P1-DIMMH1
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMMD1/P2-DIMME1/P2-DIMMF1/P2-DIMMC1/P2-DIMMG1/P2-DIMMH1
When 1 CPU is used:
1 CPU & 1 DIMM
1 CPU & 2 DIMMs
1 CPU & 3 DIMMs *
1 CPU & 4 DIMMs
1 CPU & 5DIMMs*
1 CPU & 6 DIMM
1 CPU & 7 DIMMs *
1 CPU & 8 DIMMs
1 CPU & 9 DIMMs
When 2 CPUs are used:
2 CPUs & 2 DIMMs
2 CPUs & 4 DIMMs
2 CPUs & 6 DIMMs
2 CPUs & 8 DIMMs
2 CPUs & 10 DIMMs
2 CPUs & 12 DIMMs
2 CPUs & 14 DIMMs
2 CPUs & 16 DIMMs
2 CPU & 18 DIMMs
Pins 1-2 (Reset to System )
Manufacturing Mode Select
HDD 8-15 5.25" BayHDD 0-7
DescriptionNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Not available, PCI-E 4.0 p1-x8 Slot, Low Profile From CPU 1
PCI-E 4.0 p1-x16 Slot, Low Profile From CPU 1
PCI-E 4.0 p1-x16 Slot, Low Profile From CPU 1
PCI-E 4.0 p1-x16 Slot, Low Profile From CPU 2
PCI-E 4.0 p1-x16 Slot, Low Profile From CPU 2
PCI-E 4.0 p1-x8 Slot, Low Protile From CPU 2
UID Button (Unit Identifier Button)
VGA Port
2x LAN Ports
USB 0/1/2/3 Ports
Dedicated LAN for IPMI
COM Port
Optional 2x 2.5” drives Support
Redundant Power Supply Modules
Default Setting
Connector Description
Onboard CMOS battery socketBT1
COM1/COM2 Back panel COM port/COM header for front access
FAN1-6, FANA/FANB System cooling fan headers (FAN1-FAN6, FAN A, FAN B)
IPMI_LAN Dedicated IPMI_LAN port
I-SATA0~3, I-SATA4~7 SATA 3.0 connection header supported by the Intel PCH
Front Panel Control headerJF1
JHFI1/JHFI2 Host Fabric Interface (HFI) sideband headers for the HFI cards
JIPMB1 4-pin BMC External I
2C header (for an IPMI-supported card)
JL1
JM2_1 M.2 slot
JNVI2C NVMe I2C header
JNVME1/JNVME2 NVMe Slot1/NVMe Slot2
JPI2C1 Power Supply SMBbus I2C header
JPWR1/JPWR2 8-pin Power Supply connectors
JPWR3 24-pin ATX main power supply connector
JRK1 RAID Key for onboard SATA devices
JSTBY1 Standby power header
JTPM1 Trusted Platform Module (TPM)/Port 80 connector
LAN1/LAN2 Gigabit LAN/10G LAN Ethernet ports on the backpanel
S-SATA0-3 S-SATA 3.0 connection Header supported by the Intel SCU
S-SATA4/S-SATA5 Powered S-SATA Ports SuperDOM (Disk On Module) devices
SLOT1 PCI-Express 4.0 X8 Slots supported by CPU1
T-SGPIO3 General Purpose Serial I/O port
Unit Identifier (UID) switchUID
USB0/1 (2.0) Front Accessible USB header with two USB 2.0 connections
USB2/3, USB7/8 (3.0) Rear I/O USB 3.0 ports
USB4/5 (3.0) Front Accessible USB header with two USB 3.0 connections
USB6 Internal USB 3.0 Type-A header
VGA (JFP2) Front VGA header
Chassis Intrusion header
SLOT2/SLOT3 PCI-Express 4.0 X16 Slots supported by CPU1
SLOT4/SLOT5 PCI-Express 4.0 X16 Slots supported by CPU2
SLOT6 PCI-Express 4.0 X8 Slots supported by CPU2
Each system comes with a
unique default password for
the ADMIN user.
This can be found on a sticker
on the motherboard and a
sticker on the left side of the
service tag on chassis.
If necessary, the password
can be reset by the Supermicro
IPMICFG tool.
For more information, please visit
https://www.supermicro.com/en/
solutions/management-software/
bmc-resources
Pull-out tag with BMC unique password
and Serial Number Label on the left side
of service tag.
S/N: S123456XXX0123
BMC: XXXXXXXXXXXX
PWD: AMB WODMRGT
S/N Label
PULL
Power Button
UID Button/Reset Button
Power LED
LAN2 LED
Power Failure LED
1
2
3
4
5
No. Description
Universal Information LED
USB 2.0 Ports
USB 2.0 Ports
HDD Activity LED
VGA LAN1 LED
Service/Asset Tag with
System Serial Number and
BMC Unique Password
Drive Device Activity LED
6
7
8
9
10
11
12
13
14
No. Description
12
UID
4
9
5
6
7
8 11
10
12
14
Slot Description
0-7 2.5" hot-swap SAS3 drive bays
8-15 2.5" hot-swap SATA drive bays*
* 8~11 for optional 4x hotswap PCI-E 3.0 NVMe drives support
2 31
13
Device Status LED
814 7910 2 135 4613 12 11
Latch
Latch
Processor (Reverse Side Up)
CPU Key
Carrier (Top Side Up)
CPU Key
Latch
Latch
Pro or y cess Carrier Assembl
Pin1
A
B
C
D
a
b
c
d
A, B, C, D: Peek Nut
1, 2, 3, 4: Rotating Wire
a, b, c, d: Threaded Fastener
Peek Nut
(Unlatched) (latched)
Rotating Wire
3
1
d
a
b
c
Rotating Wire
B
C
D
Rotating Wire
APeek Nut
2
Rotating Wire 4
Threaded Fastener
Heatsink
CPU tSocke
T30 Torx Driver
Use a torque
of 12 lbf
C
MAC CODE
BIOS
LICENSE
BMC CODE
JS1JS3
BMC
BMC
Firmware
BIOS
JM2_1
JF1
LAN1LAN2
FAN4 FAN3
JNCSI
JUIDB1
J J45USBR
FANB
FANA
FAN6
JPI2C1
LE4
LE6
FAN2FAN1
(Front) VGA
JBT1
JRK1
JSTBY1
JIPMB1JPME1
JNVI2C
JPWR4
JPWR2
S-SGPIO
S A5AT
JPWR3
S A6AT
JLAN2
UID LED
JS2
JLAN1
M.2 Slot
TPM/Port80
PCH
PWR
LED
BMC Heartbeat LED
BMC_LAN/USB7/8(3.0)
P1_NVME2/3
P1_NVME0/1
I-SATA0~3
USB6(3.0) USB4/5(3.0)
USB2/3
I-SATA4~7
(3.0)
USB0/1
(2.0)
VGA
COM2
COM1
S-SATA0~3
S SATA4 S-SATA5
UID/BMC
CMOS CLEAR
P1-DIMMG1
P1-DIMMF1
P1-DIMME1
P1-DIMMH1
P2-DIMMG1
P2-DIMME1
P2-DIMMF1
P2-DIMMH1
CPU2
CPU1
CPU1 SLOT1 PCIe 4.0 X8
CPU1 SLOT2 PCIe 4.0 X16
CPU1 SLOT3 PCIe 4.0 X16
CPU2 SLOT4 PCIe 4.0 X16
CPU2 SLOT5 PCIe 4.0 X16
P1-DIMMB1
CPU2 SLOT6 PCIe 4.0 X8
P1-DIMMA1
P1-DIMMD1
P1-DIMMC1
P2-DIMMC1
P2-DIMMD1
P2-DIMMB1
P2-DIMMA1
LE3
JL1
BAR CODE
VROC
J 2FP
LAN CTRL2
JVGA
JTPM-1
RAID KEY-1
Front Panel CTRL
P2-DIMMB2
P1-DIMMB2
CPLD
FAN5
REV:1.00
X12DPi-N(T)6
LAN CTRL1
(*X12DPI-N6)
X12DPI-NT6
BT1
Battery
Reset
MH15 MH16
NVME
JPL1
LEDM1
J R4PW
P I 12-D MMC
JF1
J R2PW
LE3
J R3PW
P I 12-D MMD
P I 12-D MMA
P I 12-D MMB
P I G12-D MM
P I 12-D MMH
P I E12-D MM
P I F12-D MM
J 1IPMB
US .0)B6 (3
M.2
JL1
COM2
JPME1
S- OSGPI
I-S 3ATA0-
Battery
S-S 3ATA0-
JNVI2C
US /1 .0)B0 (2
US /5 .0)B4 (3
LE4
B SIO
J M1TP
I-S 7ATA4-
F nt Aro VG
(JFP2)
Cl OSear CM
LE6 BMC_LAN
US / .0)B7 8(3
L 2AN
US / .0)B2 3(3
L 1AN
COM1
VGA
F 5AN
F 4AN
F AAN
VRO )C(JRK1
P VME2/31_N
S-S A4AT
JNCSI
UID/ tBMC Rese
F 2AN
J 1PI2C
Slot4
LEDM1
Slot3
Slot1
F BAN
J BY1ST
Slot6
L TRL2 (X )ANC 12DPi-N6
F 6AN
Slot5
Slot2
S-S A5AT
F 3AN
P I G11-D MM
P I F11-D MM
P I 11-D MMH
P I E11-D MM
P I 11-D MMB
P I 11-D MMC
P I 11-D MMA
P I 11-D MMD
F 1AN
P I 21-D MMB
P I 22-D MMB
L TRL1 (X T6)ANC 12DPi-N
P VME0/11_N
J 1PL
MH15
MH16


Product specificaties

Merk: Supermicro
Categorie: Server
Model: SuperServer SYS-220P-C9RT

Heb je hulp nodig?

Als je hulp nodig hebt met Supermicro SuperServer SYS-220P-C9RT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Server Supermicro

Handleiding Server

Nieuwste handleidingen voor Server