Supermicro SuperServer AS -2024S-TR Handleiding
Supermicro
Server
SuperServer AS -2024S-TR
Lees hieronder de 📖 handleiding in het Nederlandse voor Supermicro SuperServer AS -2024S-TR (1 pagina's) in de categorie Server. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
http://www.supermicro.com MNL-2431-QRG Rev. 1.0
A+ Server AS -2024S-TR Quick Reference Guide
Front View & Interface Rear View
Hard Drive Installation
Board Layout
No. Description
Slot1- Slot6: PCIe Expansion Card Slots
P0-DIMMA1~P0-DIMMD1 Slots (P0 slots: CPU1)
CPU1
JBT1: CMOS Clear
P0-DIMME1~P0-DIMMH1 Slots (P0 slots: CPU1)
P1-DIMMA1~P1-DIMMD1 Slots (P1 slots: CPU2)
CPU2
P1-DIMME1~P1-DIMMH1 Slots (P1 slots: CPU2)
SATA4-7: Onboard SATA3 Ports
PCIe M.2: M.2 Connector
SUPERDOM1/2: SATA3 DOM Ports (6Gb/s)
SATA0-3: Onboard SATA3 Ports
CN1~2: NVMe Ports
1
2
3
4
5
6
7
8
9
10
11
12
13
Removing a Hot-Swap
Drive Carrier from
the Chassis
1. Press the release button on
the drive carrier, which
will extend the drive
carrier handle.
2. Use the drive carrier handle
to pull the drive out of the
chassis.
Installing a 3.5" Drive
1. Position the drive above the carrier with the PCB side facing down and the connector end
toward the rear of the carrier.
2. Tilt the drive to insert it onto the two posts on the left inside of the carrier.
3. Push the right side of the drive fully into the carrier and allow the two spring locking clasps to
secure the drive.
4. Insert the drive carrier into its bay, keeping the release button on the right. When the carrier
reaches the rear of the bay, the release handle will retract.
5. Push the handle in until it clicks into its locked position
Installing a 2.5" Drive
1.Install the drive directly into the tray with four screws underneath.
2. Insert the drive carrier into its bay, keeping the release button on the right. When the carrier
reaches the rear of the bay, the release handle will retract.
3. Push the handle in until it clicks into its locked position
CPU Installation
Caution
1. Removing the Processor Force Frame
Use a Torx T20 driver to loosen the screws holding
down Force Frame in the sequence of 3-2-1. The
screws are numbered on the Force Frame next to each
screw hole.
2. Raising the Force Frame 3. Lifting the Rail Frame
5. Inserting the Carrier Frame/CPU Package 6. Lowering the Force Frame 7. Securing the Force Frame
Secure the screws in the order 1-2-3, tightening to
16.1 kgf-cm (14 lbf-in) of torque. The Force Frame
secures both the Rail Frame and CPU Package.
Caution: Tightening must be executed in proper
1-2-3 sequence to avoid causing catastrophic
damage to the socket or CPU Package.
8. The Force Frame Secured
1. Mounting the Heatsink
Screw #1
Screw #2
Screw #3
Force Frame
Rail Frame
PnP Cover Cap
Carrier Frame/
CPU Package
Processor Installation
4. Removing the External Cap and PnP
Cover Cap
External Cap
PnP Cover Cap
Heatsink Installation
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning before
connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment, disconnect power
from server by disconnecting all power cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
WARNING:
Always be sure all power supplies for this system have the same power
output. If mixed power supplies are installed, the system will not operate.
For more information go to : http://www.supermicro.com/support
!
!
!
2.5" Drive 3.5" Drive
CPU1 CPU2
#1 Screw (hidden)
#3 Screw
#4 Screw
#2 Screw
2. Securing the Heatsink
Using a diagonal pattern and a Torx T20 driver, tighten the four
heatsink screws evenly to 16.1 kgf-cm (14.0 lbf-in) torque.
Air Shroud Installation
1. Power down the system.
2. Extend the server from the rack (or remove it and
place it on a bench), then remove the cover
as described previously.
3. Place the air shroud over the DIMM slots
and CPUs as illustrated below.
The small tabs on the air shroud fit
into corresponding reception points
in the horizontal frames behind the
fans and at the rear of the
chassis.
4. Once installed, replace the
cover and push the system
back into the rack before
restoring power.
* Twelve 3.5"/2.5" hot-swap drive bays: default configuration supports up to eight
SATA (slot 4-11) and four NVMe drives (slot 0-3)
** SAS support requires optional add-on card and cables
Power Button
Reset Button
Power LED
LAN1 and LAN2 LED
Power Failure LED
1
2
3
4
5
No. Description
HDD Activity LED
Universal Information LED
Service/Asset Tag with
System Serial Number and
BMC Unique Password
Drive Device Status LED
Drive Device Activity LED
6
7
8
9
10
No. Description
HDD2
HDD1
HDD0
(NVMe /SATA(slot 0-3) *
/SAS3 )**
HDD5
HDD4
HDD3
(NVMe /SATA(slot 0-3) *
/SAS3 )**
HDD8
HDD7
HDD6
(SATA /SAS3 )* **
HDD11
HDD10
HDD9
(SATA /SAS3 )* **
8
12
RESET
1
6
2
3
4
5 7
4
RESET
10
9DescriptionNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
PCI-E 4.0 p1-x8 Slot (LP)
PCI-E 4.0 p1-x16 Slot (LP)
PCI-E 4.0 p1-x8 Slot (LP)
PCI-E 4.0 p1-x16 Slot (LP)
PCI-E 4.0 p1-x8 Slot (LP)
PCI-E 4.0 p1-x16 Slot (LP)
UID LED (Unit Identifier Button)
VGA Port
2x LAN Ports
USB 0/1/2/3 Ports
Dedicated LAN for IPMI
COM Port
Redundant Power Supply Modules
813 7910 2 112 11 35 46
Memory
The AS -2024S-TR supports up to 4TB of registered ECC DDR4-3200 SDRAM in 16 DIMM slots.
Refer to the table below for additional memory information.
NOTE: To achieve optimal memory performance, the minimum recommended is at least one
DIMM for each channel pair in the system (e g., A, C, E, G).
Memory Support
Processors and their Corresponding Memory Modules
Channel
CPU# D1 C1 B1 A1
2 DIMMs (Not Recommended)
CPU1
CPU1
16 DIMMs
CPU2
4 DIMMs (Not Recommended)
8 DIMMs
CPU1
12 DIMMs (for 7003 CPU only)
CPU1
CPU2
CPU1
CPU2
CPU2
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
E1 F1 G1 H1
CPU2 CPU
Handle
Re ease ttl Bu on
Post
Post
Insert this
side first
P0 A1-DIMM
P0 H1-DIMM
S t 3lo
S t 1lo
S t 2lo
S t 4lo
S t 5lo
S t 6lo
P0-DIMMB1
P0-DIMMG1
P0-DIMMC1
P0-DIMMF1
P0-DIMMD1
P0-DIMME1
CPU1
CPU2
P1-DIMME1
P1-DIMMD1
P1-DIMMF1
P1-DIMMC1
P1-DIMMG1
P1-DIMMB1
P1-DIMMH1
P1-DIMMA1
7810 9111213
1 2 3 4 5
6
Product specificaties
| Merk: | Supermicro |
| Categorie: | Server |
| Model: | SuperServer AS -2024S-TR |
Heb je hulp nodig?
Als je hulp nodig hebt met Supermicro SuperServer AS -2024S-TR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Server Supermicro
8 April 2024
31 Maart 2024
31 Maart 2024
31 Maart 2024
31 Maart 2024
8 Januari 2024
8 Januari 2024
8 Januari 2024
8 Januari 2024
8 Januari 2024
Handleiding Server
- Server HP
- Server Sony
- Server Asus
- Server Medion
- Server Toshiba
- Server Abus
- Server Acer
- Server Acti
- Server Allnet
- Server Apc
- Server Axis
- Server Buffalo
- Server D-Link
- Server Dell
- Server Digi
- Server Digitus
- Server Dual Bay
- Server Eaton
- Server Elac
- Server EMC
- Server Fantec
- Server Flir
- Server Freecom
- Server Fujitsu
- Server GeoVision
- Server Gigabyte
- Server Hikvision
- Server Ibm
- Server In Win
- Server Iomega
- Server Kathrein
- Server LaCie
- Server Lenovo
- Server LevelOne
- Server Linksys
- Server Maxdata
- Server Megasat
- Server Monacor
- Server Nec
- Server Netgear
- Server Provision ISR
- Server QNAP
- Server Quantum
- Server Revox
- Server Seagate
- Server Sitecom
- Server Sun
- Server Synology
- Server Trendnet
- Server Veritas
- Server Western Digital
- Server ZyXEL
- Server Conceptronic
- Server Atlona
- Server SilverStone
- Server Intel
- Server SIIG
- Server Cisco
- Server Matrox
- Server Asustor
- Server Gefen
- Server Planet
- Server Intellinet
- Server Silex
- Server G-Technology
- Server Lindy
- Server AVerMedia
- Server Black Box
- Server ATen
- Server Areca
- Server AMX
- Server SEH
- Server StarTech.com
- Server HGST
- Server Sonnet
- Server TAIDEN
- Server Advantech
- Server Moxa
- Server Smart-AVI
- Server Kramer
- Server KanexPro
- Server Avocent
- Server Hanwha
- Server Ernitec
- Server Promise Technology
- Server Raidsonic
- Server Rocstor
- Server Infortrend
- Server Opengear
- Server EXSYS
- Server Raritan
- Server Chenbro Micom
- Server Mr. Signal
- Server C2G
- Server Lantronix
- Server IStarUSA
Nieuwste handleidingen voor Server
16 April 2024
10 April 2024
10 April 2024
10 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024
25 Maart 2024
25 Maart 2024