StarTech.com POEINJ30W Handleiding

Bekijk gratis de handleiding van StarTech.com POEINJ30W (2 pagina’s), behorend tot de categorie Netwerkkaart/adapter. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.2 sterren uit 4 reviews. Heb je een vraag over StarTech.com POEINJ30W of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: June 2, 2020 11:32 AM

Product Diagram (POEINJ30W)

Component Function

1Power LEDs• A is detected.Green:Power Source

• A is not detected.O:Power Source

2Mode A LED

• Indicates that the Mode A (Green):PoE

Injector is providing power.

• Indicates that the is in idle O:PoE Injector

mode.

3PoE Out Port• Connect a to the .PoE PD DevicePoE Injector

4Data Port• Connect a to the Network SwitchPoE

Injector.

54-Pin Terminal Block

V1 and V2

• Connect an external (48-56V DC Power Source

DC Input) to the .PoE Injector

6Ground Screw

• Connect a ground connection to the Ground

ScrewDC Power Source when connecting a to

the .PoE Injector

Requirements

For the latest requirements, please visit www.startech.com/POEINJ30W

• Small Flat Head Screwdriver x 1

• Writing Utensil x 1

• PoE PD Device x 1

• Network Switch x 1

• DC Power Source or Universal Power Adapter with Type N (OD: 5.5 mm, ID: 2.5 mm)

Barrel Connector x 1

• (Optional) Phillips® Head Screwdriver x 1

• RJ45 Terminated UTP/STP Cat 5e (or better) Network Cable x 2

30W Industrial - Grade Hardened PoE Injector | 1G (1000 Mbps)

Powering the PoE Injector

Terminal Block

Connecting and installing the must be completed by a 4-Wire Terminal Connector

licensed Electrician.

Notes: Make sure that you turn o the power source before connecting the power wire

to the .PoE Injector

Do not exceed the recommend power source voltage as it may result in personal or

product damage.

1. Using a , loosen the two screws, either V1 or V2 on the Small Flat Head Screwdriver

4-Wire Terminal Connector (included).

2. Connect the from a (48 - 56V DC), or the provided Power WiresDC Power Source

Barrel Power Connector AdapterTerminal Block Connectors, to the proper (the

terminals are marked on the . Connect the positive wire to V+ PoE Injector’s Casing)

and the negative wire to V-.

3. Tighten the two screws on the .4-Wire Terminal Connector

4. Insert the in the on the 4-Wire Terminal Connector4-Wire Terminal BlockPoE

Injector.

5. To connect a second to the , repeat steps 1 - 4.Power SourcePoE Injector

6. Using a , loosen the on the .Phillips Head ScrewdriverGround ScrewPoE Injector

7. Connect the from a to the on the Ground WireDC Power SourceGround Screw

PoE Injector.

8. Using the , tighten the to secure thePhillips Head ScrewdriverGround Screw

Grounding Wire PoE Injectorto the.

(Optional) Barrel Connector

• Connect a from a Type N (OD: 5.5 mm, ID: 2.5 mm) Barrel ConnectorUniversal

Power AdapterTerminal Block to Barrel Power Connector Adapter. to the

Connecting the PoE Injector

Note: Make sure the total length of the connecting the CAT5e/6 CablePD Device

to the and the connecting the to the PoE InjectorCAT5e/6 CablePoE Injector

Remote Switch does not exceed 100 meters in total length.

1. Connect a to the on the and the other CAT5e/6 CablePoE Out PortPoE Injector

end to an RJ45 port on a (e.g. security camera, etc.).PoE PD Device

12 3456

Product specificaties