Speco Technologies ACSR62L Handleiding

Bekijk gratis de handleiding van Speco Technologies ACSR62L (32 pagina’s), behorend tot de categorie Toegangscontrolesysteem. Deze gids werd als nuttig beoordeeld door 39 mensen en kreeg gemiddeld 4.5 sterren uit 5 reviews. Heb je een vraag over Speco Technologies ACSR62L of wil je andere gebruikers van dit product iets vragen? Stel een vraag

ACSR35L

Mullion Mount•

Single-gang Wall Mount*•

*Plastic or metal.

3.0 Reader Wiring

Wiegand Magstripe

ConductorFunctionConductor Function

RedDC (8-14 VDC)RedDC (8-14 VDC)

BlackGroundBlack Ground

GreenData 0GreenClock

WhiteData 1WhiteData

BrownRed LEDaBrownRed LED

OrangeGreen LEDbOrangeGreen LED

YellowNot UsedYellowNot Used

BlueBeeperBlue Beeper

VioletRead ModecVioletRead Mode

DrainShield GroundDrainShield Ground

4.0 Cable Requirements

24 AWG minimum, multi-conductor stranded with an overall foil shield, for example Belden 9535 or similar, supporting the five conductors

comprising the physical layer of the Wiegand interface (power, ground, data 0, data 1, and/or beeper and LED). Alternatively, Belden 9539 or

similar, for all reader functions. Contact your access control system manufacturer for their specific requirements. Per the SIA’s Wiegand

specification, maximum cable length is 500 feet (152 m).

5.0 Output Formats

Wiegand (industry standard 26-bit Wiegand and custom Wiegand formats)

Magnetic Stripe (ABA Track II, clock and data, with card present)

6.0 Grounding

Shield (drain) continuity must run from the reader to the access panel. Shield (drain) and reader ground must be tied together at the access panel

and connect to an earth ground at one point.

7.0 Power

Reader may be powered by the access panel. A linear power supply is recommended for best operation.

NOTES:

aSingle Line LED: This is the standard operating mode and does not

make use of the Orange conductor. The LED is Red when the reader is

idle and flashes when a card is presented. The LED turns Green when

the Brown Conductor is pulled low by the access control panel.

bDual Line LED: This mode makes use of both the Brown and Orange

conductors. The Brown conductor controls the Red LED and the Orange

conductor controls the Green LED. LED states are determined by the

access control system option and capability.

cRead Mode: In regards to contactless smart card credentials, the

reader will only read and output the credential’s Card Serial Number

(CSN) when the Violet conductor is pulled low (connected to ground).

Otherwise, the reader will only read and output the credential’s

programmed Sector data.

QUICKARTIDE ST GU

MOBILE-READY

CONACTLESST SMARTCARD READER

This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made.

Models include

ACSR35L, ACSR62L, and ACSR64L

long-range readers.

1.0 Introduction

A key component of a physical security electronic access control system, a mobile-ready reader combining BLE and contactless smart card

technologies is based on RFID technology. In operation it is capable of reading data stored on a contactless smartcard credential via high

frequency—or reading data from mobile credential stored in a smartphone’s wallet app via BLE technology—and without physical contact, and

then passing the data obtained to the physical access control system. Access control systems typically manage and record the movement of

individuals through a protected area, such as a locked door.

2.0 Mounting Provisions

Each reader may be installed either indoors or outdoors. Mounting options shown in the table below. Use supplied #6 mounting screws, or

equivalent security screws, for installation.

ACSR62LACSR64L

•

•

Product specificaties