Sophos AP50 Handleiding
Sophos
Access point
AP50
Bekijk gratis de handleiding van Sophos AP50 (4 pagina’s), behorend tot de categorie Access point. Deze gids werd als nuttig beoordeeld door 4 mensen en kreeg gemiddeld 4.5 sterren uit 2.5 reviews. Heb je een vraag over Sophos AP50 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
Quick Start Guide
Sophos Access Points
Sophos Access Points Quick Start Guide
Introduction
UTM Wireless Protection simplifies the operation of secure and reliable
wireless networks. It combines affordable and configuration-less access
points through a built-in wireless controller in the in Sophos UTM. The
wireless controller itself centrally manages all wireless access points, all
you need to do is plug in the device anywhere in your network. The access
point will find the controller, fetch its configuration and become operable
within seconds. In addition, it easily provides wireless guest Internet access
during the initial setup, unless you explicitly deny automatic configuration.
Scope of Supply: Sophos AP10
Scope of Supply: Sophos AP30
Scope of Supply: Sophos AP50
Mount the Access Points according to their intended use
and update the UTM appliance.
All access points can be put on a stable horizontal surface or can be
mounted on the wall. The Sophos AP30 can also be mounted on the ceiling.
Please update your UTM appliance to the latest version available. Sophos
UTM version 7.508 (or higher) is required to use UTM Wireless Protection.
Note that you also need a valid UTM Wireless Protection subscription to
operate the Sophos Access Points.
AP 30
Sophos AP10 Security Notes Power supply Detachable dipole antenna Ethernet cable
Security Notes and
Regulatory Compliance
Sophos Access Points
Sophos AP50 Security Notes Power-over-Ethernet (PoE) 2 detachable antennas Ethernet cable
injector + power cord
Security Notes and
Regulatory Compliance
Sophos Access Points
Sophos AP30 Security Notes Power-over-Ethernet (PoE) 2 screws and dowels Ethernet cable
injector + power cord
Security Notes and
Regulatory Compliance
Sophos Access Points
Sophos Access Points Quick Start Guide
Connect the Access Point
to the Internal Network
The AP30 and AP50 are powered directly through the Ethernet interface
(Power over Ethernet). It is also possible to realise the power supply by a
PoE-enabled switch.
Please also note the details about the PoE injectors given in the
accompanying Operating Instructions.
Connect the Access Point
to the Power Supply
Connect the device to the power supply. Please use the power supply found
in the scope of supply.
Start the Communication between the
Access Point and the UTM Appliance
When connected to the network, the Access Points will try to receive an IP
address via DHCP. Therefore, you need either the UTM appliance (with a
DHCP server enabled and listening on the interface the Access Points are
connected to) or any other DHCP server to provide an IP address for the
Access Points.
After successfully receiving an IP address, the Access Points will
communicate with the UTM appliance. For this to happen, the UTM appliance
needs to be situated in the upstream of the Access Points, either being the
default gateway of the Access Points (which was provided by the DHCP
service) or on the default route (most likely your route to the Internet).
Please note that the actual Internet access is not necessary to use UTM
Wireless Protection. While waiting for DHCP and searching for the UTM
appliance, the Access Point power LEDs will blink slowly.
Enable UTM Wireless Protection
on the UTM Appliance
In the WebAdmin, navigate to the new Wireless Protection menu entry. On
the Global Settings tab, click the Enable button. When enabling Wireless
Protection for the first time, the Initial Setup frame will appear.
It shows the configuration which will be created: A separate Wireless “Guest”
network using WPA2 personal with DHCP for wireless clients, which will be
allowed to use DNS on the UTM appliance and the “Web Surfing” service.
The pre-shared key is auto-generated and will only be shown in this section.
This configuration is intended as a template, you can edit the settings at any
time on the Wireless Protection > Wireless Networks tab. You can also skip
the initial setup by ticking the checkbox on the bottom of the section.
Product specificaties
| Merk: | Sophos |
| Categorie: | Access point |
| Model: | AP50 |
Heb je hulp nodig?
Als je hulp nodig hebt met Sophos AP50 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Access point Sophos
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
Handleiding Access point
- Comtrend
- Longshine
- EQ-3
- Ubiquiti Networks
- Ruckus Wireless
- TP Link
- Interlogix
- Aruba
- ZyXEL
- Cisco
- Cambium Networks
- Sitecom
- Black Box
- INCA
- Amped Wireless
Nieuwste handleidingen voor Access point
2 Juni 2025
15 Mei 2025
13 Mei 2025
1 Mei 2025
25 April 2025
23 April 2025
19 April 2025
14 April 2025
14 April 2025
14 April 2025