Sophos AP30 Handleiding
Sophos
Access point
AP30
Bekijk gratis de handleiding van Sophos AP30 (16 pagina’s), behorend tot de categorie Access point. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.1 sterren uit 3 reviews. Heb je een vraag over Sophos AP30 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/16
Operating Instructions
Sophos Access Points
2Sophos Access Points
Foreword
We are pleased to welcome you as a new Sophos Access Point
customer.
These operating instructions will help you install and configure
the access point and provide technical specifications of all
Sophos access point models. In addition, please also see the
following documents that contain useful information on safety,
regulatory compliance, and configuration options:
Ì Sophos Access Points Security Notes & Regulatory
Compliance: Notes on access point security
Ì Sophos UTM Administration Guide: Configuring the UTM
hardware and software appliance
The instructions must be read carefully prior to using the
device and should be kept in a safe place. You may download
all user manuals and additional documentation from the
Astaro Knowledgebase via: astaro.com/kb.
From there, navigate to the main topics Manuals/Guides.
Introduction
UTM Wireless Protection simplifies the operation of secure
and reliable wireless networks. It combines affordable and
configuration-less access points through a built-in wireless
controller in the in Sophos UTM. The wireless controller itself
centrally manages all wireless access points; all you need
to do is plug in the device anywhere in your network. The
access point will find the controller, fetch its configuration and
become operable within seconds. In addition, it easily provides
wireless guest Internet access during the initial setup, unless
you explicitly deny automatic configuration.
Installation
AP10/30/50
Preliminary steps
Please update your UTM appliance to the latest version
available. Sophos UTM version 7.508 (or higher) is required to
use UTM Wireless Protection. Note that you also need a valid
UTM Wireless Protection subscription to operate the Sophos
Access Points.
Connect the access point to the internal network
Decide where you would prefer to place the access point,
and put the access point in that location. For mounting
instructions, see below. Now connect the access point to
your internal network by plugging in the network cable to the
access point's RJ45 Ethernet interface.
3
Connect the access point to the power supply
The AP30 and AP50 can be powered directly through the
Power-over-Ethernet-injector. Note that it is also possible
to power them by a PoE-compliant switch. For more
information on PoE-injectors, see below.
Connect the AP10 to the power supply. Please use the
power supply from the scope of supply.
Start the communication between the access point and
the UTM appliance
When connected to the network, the access point will try
to receive an IP address via DHCP. Therefore, you need
either the UTM appliance (with a DHCP server enabled and
listening on the interface the access point is connected to)
or any other DHCP server to provide an IP address for the
access point.
After successfully receiving an IP address, the access
point will communicate with the UTM appliance. For this to
happen, the UTM appliance needs to be put in the upstream
of the access points, either being the default gateway of the
access points (which was provided by the DHCP service) or
on the default route (most likely your route to the Internet).
Please note that the actual Internet access is not necessary
to use UTM Wireless Protection. While waiting for DHCP and
searching for the UTM appliance, the access point's power
LED will blink slowly.
Enable UTM Wireless Protection on the UTM appliance
In WebAdmin, navigate to the Wireless Protection menu
entry. On the Global Settings tab, click the Enable button.
When enabling Wireless Protection for the first time, the
Initial Setup frame will appear. It shows the configuration
which will be created: A separate Wireless “Guest” network
using WPA2 personal with DHCP for wireless clients, which
will be allowed to use DNS on the UTM appliance and the
“Web Surfing” service.
The pre-shared key is auto-generated and will only be shown
in this section. This configuration is intended as a template,
you can edit the settings at any time on the Wireless
Protection > Wireless Networks tab. You can also skip the
initial setup by ticking the checkbox on the bottom of the
section.
Product specificaties
| Merk: | Sophos |
| Categorie: | Access point |
| Model: | AP30 |
Heb je hulp nodig?
Als je hulp nodig hebt met Sophos AP30 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Access point Sophos
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
Handleiding Access point
- Lindy
- Cisco
- Amped Wireless
- LevelOne
- IP-COM
- Trendnet
- Steren
- Black Box
- Comtrend
- Vimar
- ICC
- Hawking Technologies
- AMX
- Luxul
- EQ3
Nieuwste handleidingen voor Access point
2 Juni 2025
15 Mei 2025
13 Mei 2025
1 Mei 2025
25 April 2025
23 April 2025
19 April 2025
14 April 2025
14 April 2025
14 April 2025