Sony SNC-ZM550 Handleiding

Sony Bewakingscamera SNC-ZM550

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony SNC-ZM550 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

4-199-273- (1)18

Network Camera

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

SNC-DH120/DH220/DH120T/DH220T

SNC-EM520/EM521/ZM550/ZM551

Owner’s Record

The model and serial numbers are located on the bottom. Record these numbers

in the spaces provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this

product.

Model No. Serial No.

Overview

This Installation Manual gives instructions for multiple types of Network Cameras:

SNC-DH120/DH220/DH120T/DH220T are PoE-type HD models, SNC-EM520/

EM521 are PoE-type SD models, and SNC-ZM550/ZM551 are HD model IPELA

HYBRID cameras.

WARNING

To reduce a risk of fire or electric shock, do not expose this

product to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualified personnel only.

WARNING

This installation should be made by a qualified service person and should

conform to all local codes.

IMPORTANT

The nameplate is located on the bottom.

Power Supply

Caution for U.S.A. and Canada (SNC-ZM550/ZM551)

The Model operates on 24 V AC or 12 V DC.

The Model automatically detects the power.

In the USA, this product shall be powered by a UL listed Class 2 Power Supply

Only.

In Canada, this product shall be powered by a CSA Certified Class 2 Power Supply

Only.

Caution for other countries (SNC-ZM550/ZM551)

The SNC-ZM550/ZM551 operates on 24 V AC or 12 V DC.

The SNC-ZM550/ZM551 automatically detects the power.

Use a power supply rated 24 V AC or 12 V DC which meets the requirements

for SELV (Safety Extra Low Voltage) and complies with Limited Power Source

according to IEC 60950-1.

CAUTION for LAN port

For safety reason, do not connect the LAN port to any network devices that might

have excessive voltage.

CAUTION for LAN port (SNC-DH120/DH220/DH120T/

DH220T/EM520/EM521)

The LAN port of this unit is to be connected only to the devices whose power

feeding meets the requirements for SELV (Safety Extra Low Voltage) and complies

with Limited Power Source according to IEC 60950-1.

Use IEEE802.3af standard compliant devices.

For customers in the U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in

this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to

comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC

Rules.

For customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, Japan.

The Authorized Representative for EMC and product safety is Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or

guarantee documents.

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.

In the case that interference should occur, consult your nearest authorized Sony

service facility.

This apparatus shall not be used in the residential area.

ATTENTION

The electromagnetic fields at specific frequencies may influence the picture of the

unit.

Notes on Use

Before Use

If you find condensation when you open the package, turn on the power after the

condensation disappears.

Remove the static electricity before operation or when touching the inside parts of

the camera.

Data and security

You should keep in mind that the images or audio you are monitoring may be

protected by privacy and other legal rights, and the responsibility for making sure

you are complying with applicable laws is yours alone.

Access to the images and audio is protected only by a user name and the password

you set up. No further authentication is provided nor should you presume that any

other protective filtering is done by the service. Since the service is Internet-based,

there is a risk that the image or audio you are monitoring can be viewed or used by

a third-party via the network.

SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR

ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR EVEN

SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY DISCLAIMS

AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE

SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR THAT IT WILL

OPERATE ERROR-FREE OR CONTINUOUSLY.

Always make a test recording, and verify that it was recorded successfully.

SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT

LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE OF

THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR ANY OTHER

MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.

Always verify that the unit is operating properly before use. SONY WILL NOT

BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,

COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT

OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE

WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER

REASON WHATSOEVER.

If you lose data by using this unit, SONY accepts no responsibility for restoration of

the data.

Personal information

The images taken by the system using this device can identify individuals and thus

they fall under “personal information” stipulated in the “Act on the Protection of

Personal Information”. Please handle the video data appropriately according to law.

Information recorded using this product may also be “personal information”. Upon

disposal, transfer, repair, or any other occasion where this product or storage media

is passed on to a third party, practice due care in its handling.

Operating or storage location

Do not shoot an extremely bright object (an illumination, the sun, etc.). Also, avoid

operating or storing the camera in the following locations, as these can be a cause of

a malfunction.

Extremely hot or cold places (Operating temperature: -10°C to +50°C [14°F to

122°F])

Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near

heaters)

Close to sources of strong magnetism

Close to sources of powerful electromagnetic radiation, such as radios or TV

transmitters

Locations subject to strong vibration or shock

Humid or dusty locations

Locations exposed to rain

Locations under the influence of fluorescent light or reflection of a window

Under an unsteady light (the image will flicker.)

Ventilation

To prevent heat buildup, do not block air circulation around the camera.

Power supply (SNC-DH120/DH120T/DH220/DH220T/EM520/

EM521)

The power of this model is supplied by network cable.

Use the network cable UTP, category-5.

Damage to the network cable may result in fire or electric shock.

Transportation

Always turn off the power when carrying.

When transporting the camera, repack it as originally packed at the factory or in

materials of equal quality.

Cleaning

Use a blower to remove dust from the lens.

Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn stains

can be removed using a soft cloth dampened with a small quantity of detergent

solution, then wipe dry.

Do not use volatile solvents such as alcohol, benzene or thinners as they may

damage the surface finishes.

Note on laser beams

Laser beams may damage image sensors. You are cautioned that the surface of image

sensors should not be exposed to laser beam radiation in an environment where a laser

beam device is used.

Phenomena Specific to Image Sensors

The following phenomena that may occur in images are specific to image sensors.

They do not indicate a malfunction.

White flecks

Although the image sensors are produced with high-precision technologies, fine

white flecks may be generated on the screen in rare cases, caused by cosmic rays, etc.

This is related to the principle of image sensors and is not a malfunction.

The white flecks especially tend to be seen in the following cases:

- when operating at a high environmental temperature

- when you have raised the gain (sensitivity)

- when using the slow shutter

Aliasing

When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.



About the Supplied Manuals

Installation Manual (this document)

This Installation Manual describes the names and functions of parts and controls

of the Network Camera, gives connection examples and explains how to set up the

camera. Be sure to read the Installation Manual before operating.

The pictures of SNC-DH120T are mainly used in explanatory examples.

User’s Guide (stored in the CD-ROM)

The User’s Guide describes how to set up the camera and how to control the camera

via a Web browser.

After installing and connecting the camera correctly, operate referring to this User’s

Guide.

Using the CD-ROM Manuals

The supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.

Preparations

The Adobe Reader Version 6.0 or higher must be installed on your computer in order

to use the guides stored in the CD-ROM disc.

Note

If Adobe Reader is not installed, it may be downloaded from the following URL: http://

www.adobe.com/

Reading the manual in the CD-ROM

1 Insert the CD-ROM in your CD-ROM drive.

A cover page appears automatically in your Web browser.

If it does not appear automatically in the Web browser, double-click on the

index.htm file on the CD-ROM.

2 Select and click on the manual that you want to read.

This opens the PDF file of the manual.

Clicking an item in the Table of Contents allows you jump to the relevant

page.

Notes

The files may not be displayed properly, depending on the version of Adobe

Reader. In this case, install the latest version, which you can download from the URL

mentioned in “Preparations” above.

If you have lost or damaged the CD-ROM, you can purchase replacement. Contact

your Sony service representative.

Smartphone viewer

This product is equipped with a Smartphone viewer.

With Smartphone viewer, you can display an image from a network camera, pan, tilt

and zoom that camera, on your smartphone.

For more details, see “Smartphone viewer User’s Manual” at the following URL:

http://www.sony.net/ipela/snc

Location and Function of Part

The figure shows the camera without the dome casing.

Side 

Cable is not connected when the unit comes from the factory.

 Power input/output cable (supplied, factory-connected) (SNC-ZM550/ZM551)

Connect to a AC 24 V/DC 12 V power supplying device.

The screws on the connector tip at the end of the cable can be used to attach an

extension cable.

 I/O (Input/Output) cable (supplied) (SNC-DH120T/DH220T/EM521/ZM551)

This cable is provided with a sensor input and an alarm output.

The wires of the cable control the following signals.

Color of wire Name

Red Sensor In +

White Sensor In – (GND)

Black Alarm Out 1 +

Yellow Alarm Out 1 –

Brown Unused

Green Unused

 For details on each function and required settings, see the User’s Guide stored

in the supplied CD-ROM.

 For the wiring, see “Connecting the I/O cable.”

 Camera head holder

 Lens

 BNC cable (supplied, factory-connected) (SNC-ZM550/ZM551)

Outputs SLOC (IP coaxial transfer) signals and video signals.

 LAN cable (RJ-45) (supplied and connected to the camera at the factory) (SNC-

DH120/DH120T/DH220/DH220T/EM520/EM521)

Use the network cable (UTP, category-5) for network communications and PoE*

power supply.

 See “Connect to the Network” for connection.

(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant

devices.)

 Wiring cover

When you wire indoors, remove this cover and feed the cables through it.

Caution

Take care not to trap the cables between the camera and the ceiling or the wall. If

the cable is trapped, it may cause a fire or electric shock due to breaking.



Inside 

 Camera unit

 EXT CTRL (external control input/output) connector

(SNC-DH120T/DH220T/EM521/ZM551)

Connect the supplied I/O cable to this connector.

 SLOC (IP coaxial transfer/video output) port (VIDEO OUT) (SNC-ZM550/

ZM551)

Connect the supplied BNC cable.

Use this port when connecting the unit to a network using a coaxial cable.

When using a composite signal, set the network connection change switch to

LAN.

Also use this port to output composite video signals from this unit.

A connection to compatible equipment is necessary when connecting to a

network using a coaxial cable.

For connection details, refer to the instruction manuals of the equipment on

the receiving end.

Note

The output analog image may not display correctly, depending on the

video format and image size settings.

The image may not display properly in the horizontal and/or vertical

plane.

The image may be reduced.



 Network connection change switch (SNC-ZM550/ZM551)

Use this switch to change between a network connection to a LAN (network)

port (RJ-45) and a network connection using a coaxial cable.

 NTSC/PAL switch

Switching the video output.

 ZOOM/FOCUS switch

Use this switch to adjust lens’ zoom and focus. Slide the switch lever to select

the desired function.

[W] WIDE: Zoom out

[T] TELE: Zoom in

[N] NEAR: Focus on a nearby subject

[F] FAR: Focus on a distant subject

 MONITOR output jack

Output the composite video signal from the camera.

Monitor out is used when you adjust the angle of view. After usage,

disconnect the video cable.

Notes

Do not connect to the video cable until the POWER indicator lights up.

SNC-DH120/DH120T/DH220/DH220T/EM520/EM521:

Be aware that the system performance may be influenced, if monitor

out is set to on. Be sure to set it to off and disconnect the video cable

when you do not use it.

When using this jack, turn on monitor out in the system settings. After

usage, turn the setting off and disconnect the video cable.

 For details on system settings, see the User’s Guide.



 Reset switch

To reset the camera to the factory default settings, hold down this switch with

a point and supply the power to the camera.

 Camera head fixing screw

First loosen the screw and face the camera head to the desired direction, then

tighten the screw to fix it.

 Easy Focus button

Press this button to automatically adjust the focus easily.

 Camera installation hole (2 positions)

Make sure to tighten the screws securely when installing the camera.

 LAN (network) port (RJ-45)

Connect the supplied LAN cable.

 AC/ DC (power input) terminal (SNC-ZM550/ZM551)

Connect the supplied power input cable.

 NETWORK indicator (Green/Orange)

The indicator lights up or flashes when the camera is connected to the

network. The indicator is off when the camera is not connected to the

network. When 100BASE-TX is connected, the indicator turns green. When

10BASE-T is connected, the indicator turns orange.

The indicator also turns green when SLOC (IP coaxial transfer) is selected.

(SNC-ZM550/ZM551)

 POWER indicator (Green)

When the power is supplied to the camera, the camera starts checking the

system. If the system is normal, this indicator lights up.

(continued on the reverse side)



 2010 Sony Corporation Printed in China

1, 2

SNC-DH120/DH220/EM520/

ZM550

SNC-DH120T/DH220T/EM521/

ZM551









Dome casing

wrench

Bracket

(supplied)

Ceiling

3, 4

notch

mark

Wire rope

Ceiling

Wire rope (supplied)

Shoulder

screw

(supplied)

Wire rope

Camera unit mounting

screw (supplied) (2)

Guide

When ZOOM/FOCUS switch slides to N/F

When ZOOM/FOCUS switch slides to W/T

Preparations

Connecting the Cables to the Camera 

Before installation, connect the supplied cables to the camera as required for your

usage and wire them.

1 Remove the screw on the bottom of the camera unit to detach the cable cover.

2 Pass the cables through the hole on the bottom of the camera unit.

3 Connect the cables to the connectors on the camera unit.

BNC cable: Connected to the SLOC port (SNC-ZM550/ZM551)

I/O cable: to EXT CTRL connector (SNC-DH120T/DH220T/EM521/ZM551)

Power input cable: Connected to the AC/ DC (power input) terminal

(SNC-ZM550/ZM551)

LAN cable: Connected to the LAN port (SNC-DH120/DH120T/DH220/DH220T/

EM520/EM521)

Network cable (not supplied): Connect to the LAN port (SNC-ZM550/ZM551)

4 Wire the cables along the cable guides on the camera unit. Position the

cables under the cable clamps.

Note

To prevent the cables from being trapped by the dome casing, be sure to wire

them using the cable guides and clamps.

5 Pull the cables gently from the bottom of the camera unit to take in the

slack, and fix the cable cover with the screw.

To install the camera for indoor wiring, push the indoor wiring cover outwards

and then remove it and pass the cables through it.

Installation

Caution

If you attach the camera in a high location such as wall or ceiling, etc., entrust

the installation to an experienced contractor or installer.

If you install the camera in a high location, ensure that the ceiling is strong

enough to withstand the weight of the camera plus mounting brackets and

screws, and then install the camera securely. If the ceiling is not strong enough,

the camera may fall and cause serious injury.

To prevent the camera from falling, make sure to attach the supplied wire rope.

If you attach the camera to the ceiling, check periodically, at least once a year, to

ensure that the connection has not loosened. If conditions warrant, make this

periodic check more frequently.

Deciding the Installation Location of the Camera 

After deciding the direction in which the camera will shoot, make the required hole

(ø 50 mm (2 inches)) for the connecting cables using the supplied template. Then

decide the two or four mounting hole positions to install the bracket.

Mounting screws

The supplied bracket is provided with ø 4.5 mm (3/16 inch) mounting holes. Install the

bracket on a ceiling or wall with screws through two or four mounting holes: two

83.5 mm (3 9/32 inches)-pitched holes or four 85.7 mm (3 3/8 inches)-pitched holes.

The required mounting screws differ depending on the installation location and its

material. (Mounting screws are not supplied.)

Steel wall or ceiling: Use M4 bolts and nuts.

Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be

15 mm (5/8 inch) or more.

Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.

Junction box: Use screws to match the holes on the junction box.

Note

Use the supplied screws to install the unit. Using other screws may cause damage

inside the unit.

Installing the Camera 

1 Remove the dome casing.

SNC-DH120/DH220/EM520/ZM550

 Pull out the screw cover and loosen the screw with a screwdriver.

 Turn the dome casing to the curved mark position on the camera unit,

and remove the dome casing from the camera unit. When the screw

catches on the screw hole, pull up the screw.

SNC-DH120T/DH220T/EM521/ZM551

 Loosen the screw with the wrench (supplied).

 Turn the dome casing to the curved mark position on the camera unit,

and remove the dome casing from the camera unit. When the screw

catches on the screw hole, pull up the screw.

2 Install the supplied bracket on the ceiling or wall.

Refer to “Mounting screws” for screws to be used.

3 Fix the supplied wire rope to the camera unit and the ceiling or wall.

 Fix the wire rope with the supplied shoulder screw to the hole for the

wire rope on the bottom of the camera unit.

Pass the wire rope between the wire rope guides.

 Fix the wire rope to the ceiling or wall.

4 Attach the camera unit to the bracket.

 Insert the supplied two camera unit mounting screws into the two

mounting holes of the camera.

The screws have a fall-prevention mechanism. The screws inserted into the screw

holes of the camera unit do not fall even if you turn the camera unit upside down.

  Align the notch on the camera with the mark on the bracket.

Turn the camera unit in the direction of the arrow.

Tighten the camera unit mounting screws.

Notes

Use the supplied screws for installation. otherwise, you may not install the camera

unit properly, even a falling may occur.

If you cannot use screws on a ceiling or wall, or if you want to make the camera less

conspicuous, use the YT-ICB45/YT-ICB140 in-ceiling bracket (optional) with which

you can mount the camera on the ceiling.

For this model, install the camera to the position on the side brackets of 

YT-ICB45/YT-ICB140. Refer to the Installation Instructions of YT-ICB45/

YT-ICB140 for detail information.

Adjusting the Camera Direction and Coverage 

1 Loosen the camera head fixing screw.

2 Adjust the camera to turn the lens in the desired direction.

3 Tighten the camera head fixing screw to fix the camera.

4 Slide the ZOOM/FOCUS switch to W/T to adjust the zoom.

The zoom indicator is displayed on the monitor.

5 Press the Easy Focus button to automatically adjust the focus.

6 Repeat steps 1 to 5 until the coverage and the focus are determined.

Notes

When you adjust the camera head angle without loosening camera head fixing

screw, an internal part may be damaged.

When the lens is not put in the slit of the camera head holder, the moving range of

the camera head is limited.

If the camera head is too heavy to be adjusted, loosen the camera head fixing

screw until it moves freely.

When adjusting the angle, be sure that the TOP mark on the camera head section

faces the ceiling. If the camera is installed with the TOP mark facing the floor, the

image appears upside down.

If you cannot achieve satisfactory focus with the Easy Focus button due to the

shooting environment, slide the ZOOM/FOCUS switch level to N/F to focus

manually. The focus indicator is displayed on the monitor.

Poor focus may also be caused by the dome case assembly. Readjust the focus

using the system menu.

For details, refer to the User Guide of the equipment.

Note

Do not turn the lens more than 360 degrees, as this may damage the wiring inside,

which may cause failure on video output.

Attaching the Dome Casing 

1 Align the carved mark on the dome casing with that on the camera unit, and

turn the dome casing in the direction of the arrow.

2 Secure the screw. Only the SNC-DH120/DH220/EM520/ZM550 cover should

be attached.

3 Remove the protecting film on the dome cover.

Connection

Connect to the Network

SNC-DH120/DH120T/DH220/DH220T/EM520/EM521 

Connect the LAN connector of the camera to a PoE* supported device (such as a hub)

using the network cable (straight, not supplied).

The electrical power is supplied through the network cable. For details, refer to the

instruction manuals of the PoE supported devices.

(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant devices.)

SNC-ZM550/ZM551 

Connect to a network using a coaxial cable or LAN.

Connecting via a coaxial cable

When the network connection change switch is set to SLOC, connect to a

network via a coaxial cable.

The maximum coaxial cable length is RG-59 300 m.

Notes

The high-frequency characteristics of coaxial cables may differ, even

if the cables are of the same classification. Use a high-quality, high-

frequency coaxial cable with this unit.

 For details, refer to the instruction manual of the connecting SLOC

device. For further details, please consult an authorized Sony dealer.

When connecting with a coaxial cable, do not connect a network cable

to this unit.



Connecting via LAN

When the network connection change switch is set to LAN, use a network

cable (straight, not supplied) to connect this unit’s LAN port to the

network’s router or hub.

Connecting to a computer

Use a network cable (crossover, not supplied) to connect this unit’s LAN

port to the computer’s network connector.

Connecting to 12 V DC or 24 V AC source 

SNC-ZM550/ZM551

Connect the power input cable of the camera to a 12 V DC or 24 V AC source.

Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. Each usable

voltage ranges are as follows.

12 V DC: 10.8 V to 13.2 V

24 V AC: 21.6 V to 26.4 V

- In the USA, The product shall be powered by a UL Listed Class 2 Power

Supply Only.

- In Canada, The product shall be powered by a CSA certified Class 2 Power

Supply Only

Use UL cable (VW-1 style 10368) for these connections.

recommended cable

DC12 V: AC24 V:

CABLE(AWG) #26 #24 #22 #26 #24 #22

Max. length(m) 4 10 18 27 43 73

Connecting the I/O Cable

Connect the wires of the I/O cable as follows:

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside

3.3 V

47 K

Sensor input +

GND

Mechanical switch

Open collector

output device

Outside

GND

30 K

10 K

Ω(GND)

Sensor input −

Wiring diagram for alarm output

Camera inside

Alarm Output +

Magnet relay –

24 V AC

24 V DC

1 A or less

Alarm Output –

Outside

5 V

Circuit example

GND

Specifications

Compression

Video compression format JPEG/MPEG4/H.264

Maximum frame rate SNC-DH120/DH120T/ZM550/ZM551

H.264: 30 fps (1280 × 720)

SNC-DH220/DH220T

H.264: 30 fps (1920 × 1080)

SNC-EM520/EM521

H.264: 30 fps (800 × 600)

Camera

Signal system NTSC color system/PAL color system (switchable)

Image device

SNC-DH120/DH120T/EM520/EM521/ZM550/ZM551

1/3type CMOS (Exmor)

Effective picture elements:

Approx. 1,390,000

SNC-DH220/DH220T

1/2.8type CMOS (Exmor)

Effective picture elements:

Approx. 3,270,000

Synchronization Internal synchronization

Minimum illumination

SNC-DH120/DH120T/EM520/EM521/ZM550/ZM551

F1.2/AGC 42 dB/50 IRE (IP)

Color 0.50 lx, Black & White 0.30 lx

SNC-DH220/DH220T

F1.2/AGC 42 dB/50 IRE (IP)

Color 0.70 lx, Black & White 0.45 lx

Lens

Focal length 3.1 mm to 8.9 mm

Maximum relative aperture F1.2 to F2.1

View angle

SNC-DH120/DH120T/ZM550/ZM551: 1280 × 1024

Vertical: 67.4° to 25.0° Horizontal: 85.4° to 31.2°

SNC-DH220/DH220T: 1920 × 1440

Vertical: 65.2° to 24.2° Horizontal: 88.5° to 32.3°

SNC-EM520/EM521: 800 × 600

Vertical: 67.4° to 25.0° Horizontal: 85.4° to 31.2°

Minimum object distance 300 mm

Interface

LAN (PoE)* 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

* The PoE power supply feature is not

available on SNC-ZM550/ZM551.

I/O port (SNC-DH120T/DH220T/EM521/ZM551 only)

Sensor input: × 1, make contact, break contact

Alarm output: × 1, 24 V AC/DC, 1 A

(mechanical relay outputs electrically isolated

from the camera)

BNC (SLOC port) (SNC-ZM550/ZM551 only)

1.0 Vp-p, 75 ohms, unbalanced, sync negative

(during video output)

Others

Power SNC-DH120/DH120T/DH220/DH220T/EM520/

EM521: IEEE802.3af compliant (PoE system)

SNC-ZM550/ZM551: DC 12V/AC 24V

Power consumption SNC-DH120/DH120T/DH220/DH220T/EM520/

EM521: 6.0 W max.

SNC-ZM550/ZM551: 7.0 W max.

Operating temperature Start temperature: 0°C to 50°C (32°F to 122°F)

Working temperature: −10°C to +50°C (14°F to 122°F)

Storage temperature –20°C to +60°C (–4°F to +140°F)

Operating humidity 20% to 80%

Storage humidity 20% to 95%

Dimensions (diameter/height) 

SNC-DH120/DH220/EM520/ZM550:

140 mm × 118 mm (5 5/

8 inches × 4 3/4 inches)

SNC-DH120T/DH220T/EM521/ZM551:

140 mm × 119 mm (5 5/

8 inches × 4 3/4 inches)

Mass SNC-DH120/DH220/EM520/ZM550:

Approx. 715 g (1 lb 9.2 oz), not including the

cables and bracket

SNC-DH120T/DH220T/EM521:

Approx. 945 g (2 lb 1.3 oz), not including the

cables and bracket

SNC-ZM551:

Approx. 965 g (2 lb 2.0 oz), not including the

cable and bracket

Supplied accessories CD-ROM (User’s Guides, and supplied

programs) (1), Bracket (1), Template (1),

Wire rope (1), Camera unit mounting screws (2),

Shoulder screw M4 (1), Wrench (SNC-DH120T/

DH220T/EM521/ZM551) (1), I/O cable (SNC-

DH120T/DH220T/EM521/ZM551) (1), LAN

cable (1) (SNC-DH120/DH120T/DH220/DH220T/

EM520/EM521), BNC cable (SNC-ZM550/ZM551),

Power input cable (SNC-ZM550/ZM551),

Installation Manual (this document) (1 set)

Optional accessory

In-ceiling bracket YT-ICB45*, YT-ICB140*

* Using the fixture position on the bracket.

Design and specifications are subject to change without notice.

Recommendation of Periodic Inspections

In case using this device over an extended period of time, please have it

inspected periodically for safe use.

It may appear flawless, but the components may have deteriorated over time,

which may cause a malfunction or accident.

For details, please consult the store of purchase or an authorized Sony dealer.

Adobe and Acrobat Reader are trademarks of Adobe Systems

Incorporated in the United States and/or other countries.

sloc™ is a trademark owned by the Intersil Corporation family of

companies.



indoor wiring cover

* mark indicates the

approximate zoom position.

The number indicates

the zoom position.

* mark indicates the

approximate focus position.

The number indicates

the focus position.

Unit: mm (inches)

85.7 (3 3/8)

83.5 (3 9/32)

Hole for connecting

cables ø50

Horizontal mark

Hole for installing

the bracket

Vertical mark

85.7 (3 3/8)

cable cover

Rating label

SNC-DH120/DH220/EM520/

ZM550

SNC-DH120T/DH220T/EM521/

ZM551

Unit: mm (inches)

Ø140 (5 5/8)

118 (4 3/4)

Ø140 (5 5/8)

119 (4 3/4)

Ceiling

Network cable

(straight, not

supplied)

10BASE-T/

100BASE-TX

PoE supported

device (such as

a hub)

LAN cable

SNC-DH120/DH120T/DH220/DH220T/EM520/EM521

SNC-DH120/DH220/EM520/

ZM550

SNC-DH120T/DH220T/EM521/

ZM551

Network cable

(straight, not

supplied)

10BASE-T/

100BASE-TX

Hub

Power input cable

Ceiling

Video monitor (etc.) Network device

LAN port (RJ-45)

Network cable

10BASE-T/100BASE-TX

Video output

terminal

Coaxial cable maximum length:

RG-59 300 meters

Coaxial cable

SLOC-compatible

device

SLOC

connector

SNC-ZM550/ZM551

+ −

Network

Product specificaties

Merk:	Sony
Categorie:	Bewakingscamera
Model:	SNC-ZM550
Kleur van het product:	Black, White
Gewicht:	715 g
Breedte:	140 mm
Diepte:	140 mm
Hoogte:	118 mm
Soort:	IP-beveiligingscamera
Ondersteunde videoformaten:	H.264, MPEG4
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond
Ondersteunde video-modi:	720p
Maximum resolutie:	1280 x 1024 Pixels
Totaal aantal megapixels:	1.3 MP
Diameter:	140 mm
Minimale belichting:	0.3 Lux
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
Video bewegings-detectie:	Ja
Zoomcapaciteit:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Brandpuntbereik:	3.1 - 8.9 mm
Certificering:	FCC, VCCI
Formaat analoog signaal:	NTSC, PAL
Omvang optische sensor:	1/3 "
Aansluiting voor netstroomadapter:	Ja
Type beeldsensor:	CMOS
Optische zoom:	2.9 x
Camera sluitertijd:	1/1 - 1/10000 s
Interface:	RJ-45
Witbalans:	Fluorescent L, Lamp, Manual
Type camerasluiter:	Elektronisch
Ondersteunde grafische resoluties:	320 x 192,320 x 240,384 x 288,640 x 368,704 x 576,720 x 480,720 x 576,768 x 576,1280 x 800,1280 x 960,1024 x 576 (WSVGA),1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),640 x 480 (VGA),800 x 480 (WVGA),800 x 600 (SVGA)
Voldoet aan industriestandaarden:	IEEE802.1x
Bekabelingstechnologie:	10/100Base-T(X)
Temperatuur bij opslag:	-20 - 60 °C
Maximaal 30 frames per seconde:	30 fps
Ondersteunde netwerkprotocollen:	IPv4, IPv6, TCP, UDP, ARP, ICMP, IGMP, HTTP, HTTPS, FTP (client only), SMTP, DHCP, DNS, NTP, RTP/RTCP, RTSP, SNMP (MIB-2)
Luchtvochtigheid bij opslag:	20 - 95 procent
Scherpstellen:	1.2 - 2.1
PTZ control:	Ja
Minimale processor:	Intel Core 2 Duo (2 GHz)
Draaihoek:	180 °
Pan bereik:	0 - 180 °
Dag/nacht modus:	Ja
Ondersteunde browser:	IE 6.0, Firefox v3.5, Safari v4.0, Google Chrome v4.0
Minimale RAM:	1024 MB
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
AC-ingangsspanning:	24 V
Stroomverbruik (typisch):	7 W
Bedrijfstemperatuur (T-T):	-10 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Bereik kantelhoek:	0 - 70 °