Smart-AVI HDCIR Handleiding

Smart-AVI AV extender HDCIR

Lees hieronder de 📖 handleiding in het Nederlandse voor Smart-AVI HDCIR (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Notice

The information contained in this document is

subject to change without notice. Smart-AVI makes

no warranty of any kind with regard to this material,

including but not limited to, implied warranties of

merchantability and fitness for any particular

purpose.

Smart-AVI will not be liable for errors contained herein

or for incidental or consequential damages in

connection with the furnishing, performance or use

of this material.

No part of this document may be photocopied,

reproduced or translated into another language with

out prior written consent from Smart-AVI.

For the complete manual, visit www.smartavi.com.

Use a single CAT5 to broadcast

IR up to 1000ft away(333m)

HDC-IR

www.smartavi.com

User Manual

2840 N. Naomi Ave.

Burbank, California 91504

Phone: (818) 565-0011

Facsimile: (818) 565-0020

Technical Specifications

METI

IR Eye input

IR Frequency Range 30 KHz to 80KHz

Capture Distance Up to 25ft

Cable Connector

IR Signal Indicator Green LED

Power Requirements 5VDC 30mA

Signal Type

TTL

IR Emitter output

IR Frequency Range

30KHz to 80KHz

Emitter Distance

Up to 10’

Cable Connector 3.5mm mono jack

IR Signal Indicator

Box

Power Requirments 12VDC 1A single power up to 250’

Cable Link CAT5 568A or 568B

Dimension

Weight

.25lb (0.9 Kg.)

HDC-IR SPECIFICATIONS

3.5mm stero jack

Red LED

2.5”x2.5”x1.0”

Introduction

The HDC-IR range of products allow the extension

of Infra Red control signals using single CAT5 UTP

(category 5, unshielded twisted pair) cable. The

HDC-IR is the first product for this application.

Features

Uses easy to install, inexpensive CAT5.

Output reaches up to 1000 feet (300 m).

Sends IR and Power signals over CAT5

Bi-directional IR.

High ground loop immunity.

Built-in lightning, power surge and transient

protection.

Remote Units come with Buffered Outputs.

Compact Enclosure.

Optional power supply for remote unit.

Fully compliant with standard modulated IR

and the latest IRDA.

Fully transparent path for all protocols and

data transfers.

What’s in the box?

HDC-IR

Please check the contents of the package before

beginning installation.

Installation Diagram

ytQ metI noitpircseD

DEL-MS

EYE-MS

Installation Instructions

Operating Instructions

Once installation is completed, verify that the power is

present at all devices in the system. The peripheral

devices should be ready for use.

sdradnatSgniriW5TAC

#ni AP 865AIT/AI BE 865AIT/AIE

e1 pirtsneerghtiwetih eW pirtsegnarohtiwetihW

n2 eergdilosroepirtsetihwhtiwneerG egnarodilosroepirtsetihwhtiwegnarO

3 epirtsegnarohtiwetihW epirtsneerghtiwetihW

e4 ulbdilosroepirtsetihwhtiweulB eulbdilosroepirtsetihwhtiweulB

e5 pirtseulbhtiwetih eW pirtseulbhtiwetihW

6 egnarodilosroepirtsetihwhtiwegnarO dilosroepirtsetihwhtiwneerG

n7 worbdilosroepirtsnworbhtiwetihW nworbdilosropirtsnworbhtiwetihW

n8 worbdilosroepirtsetihwhtiwnworB nworbdilosroepirtsetihwhtiwnworB

Connecting the IR

Use the Diagram for the IR connection.

Connecting the Transmitter

1. Connect the IR LED to the IR window on the source

device.

2. Connect power supply to the unit. Observe LED

lighting up indicating power present.

Connecting the Receiver

Connect IR LED to the IR window on the souce device.

2. Connect the IR Eye to the Receiver.

3. Observe LED lighting indicating power present.

Connect the Transmitter to the Receiver

Connect the transmitter to the receiver using

Category 5 UTP cable (Purchased separately). The

CAT 5 UTP cable, if purchased in

bulk, will be wired using 568A or

568B wiring standard. Once

connected, check that the power

LEDs on both the receiver and the

transmitter are on, IR status LED is on and RX LED is

flashing when Remote control is used indicating that

communication is in progress.

HDC-IR-TX

HDC-IR-RX

PS12VD1A

IR Transmitter

IR Receiver

IR Emitter

IR Eye “Optional”

Power supply12VDC1A

Supports any IR Remote Control.

HDC-IR can be used 2 ways,

1. enabling the remote side to control the DVD,

or any other source device. (the IR eye would

be connected at the remote).

2. enabling the source side to turn off or on the

remote TV/Monitor (the IR eye would be

connected at the source.

Product specificaties

Merk:	Smart-AVI
Categorie:	AV extender
Model:	HDCIR
Kleur van het product:	Zwart
Gewicht:	900 g
Soort:	AV-zender
Maximum resolutie:	- Pixels
Aansluiting voor netstroomadapter:	Ja
Afmetingen (B x D x H):	85 x 85 x 35 mm